ASRock K10N78hSLI-GLAN manual How to install eSATAII?

Page 28

How to install eSATAII?

SATAII_6 (PORT5)

eSATAII_TOP

1.In order to enable the eSATAII port of the I/O shield, you need to connect the orange SATAII connector (SATAII_6 (PORT5); see p.11 No.11) and the eSATAII connector (eSATAII_TOP; see p.11 No.35) with a SATA data cable first.

Connect the SATA data cable to the orange SATAII connector

(SATAII_6 (PORT5))

Connect the SATA data cable to the eSATAII connector (eSATAII_TOP)

2.Use the eSATAII device cable to connect eSATAII device and the eSATAII port of the I/O shield according to the eSATAII connector that you connect the SATA data cable.

Connect one end of the eSATAII

device cable to eSATAII device

Connect the other end of the eSATAII device cable to eSATAII port of the I/O shield

28

Image 28

Contents K10N78hSLI-GLAN Copyright Notice DisclaimerContents Bios Setup Utility Software SupportPackage Contents IntroductionSpecifications Bios Feature Unique FeatureSupport CD HardwarePage Page CPU Motherboard Layout DDR2ASRock eSATAIISPDIF I/O Table for Audio Output ConnectionInstallation Pre-installation PrecautionsCPU Installation Installation of CPU Fan and HeatsinkInstallation of Memory Modules Dimm Dual Channel Memory ConfigurationsInstalling a Dimm Notch breakInstalling an expansion card Expansion Slots PCI and PCI Express SlotsHybrid Slitm Operation Guide Minimum System Configuration for Hybrid SlitmSupported PCI Express Card for Hybrid Slitm Enjoy the benefit of Nvidia Hybrid Slitm Jumpers Setup PS2USBPW1Onboard Headers and Connectors IDE1Serial ATA Sata Power Cable Header CPU Fan Connector White end 2-pin Hdmispdif Header Connection Guide What is eSATAII? ESATAII Interface IntroductionHow to install eSATAII? Comparison between eSATAII and other devices Sataii Hard Disk Setup Guide Western DigitalPage What is Hot Plug Function? What is Hot Swap Function?Sata / Sataii HDD Hot Plug Feature and Operation Guide Points of attention, before you process the Hot PlugHow to Hot Plug a Sata / Sataii HDD How to Hot Unplug a Sata / Sataii HDDInstalling Windows XP / XP 64-bit Without RAID Functions Driver Installation GuideMake a Sata / Sataii driver diskette Install Windows XP / XP 64-bit OS on your system Install Windows VistaTM / VistaTM 64-bit OS on your systemInstalling Windows XP / XP 64-bit With RAID Functions Use RAID Installation Guide to set RAID configuration\ RAID Installation Guide \ I386 \ AHCIVista For Windows VistaTM OSSet the Sata Operation Mode option to RAID Untied Overclocking Technology Bios Menu Bar IntroductionNavigation Keys Main ScreenTo jump to the Exit Screen or exit the current screen System Time HourMinuteSecondMonitor Boot Security Exit CPU ConfigurationAdvanced Screen MainOverclock Mode Boot Failure GuardAM2 Boost CPU Frequency MHzSecure Virtual Machine Enhanced Halt StateProcessor Maximum Frequency North Bridge Maximum FrequencyProcessor Voltage Processor Target FrequencyNorth Bridge Target Frequency CPU Frequency MultiplierFlexibility Option Memory Controller ModeCAS Latency CL Addr/Cmd Fine Delay CS/ODT Fine DelayMA Timing Bank InterleavingFront Panel Hybrid SLIShare Memory Primary Graphics AdapterCPU NB Link Speed CPU NB Link WidthDram Voltage Chipset Core VoltageAcpi Configuration Sata Operation Mode IDE Device ConfigurationAcpi Hpet Table OnBoard IDE ControllerLBA/Large Mode PIO ModeDMA Mode Block Multi-Sector TransferPCIPnP Configuration PCI Latency TimerA.R.T 32Bit Data TransferFloppy Configuration Super IO ConfigurationOnBoard Floppy Controller Serial Port AddressUSB Configuration USB Controller EnabledUSB Controller USB 2.0 SupportTarget CPU Temperature Hardware Health Event Monitoring ScreenCPU Quiet Fan Target Fan SpeedBoot Screen Boot Settings ConfigurationBoot From Onboard LAN Boot Up Num-LockChange Supervisor Password Main Advanced Monitor BootSecurity Screen Load Optimal Defaults Exit ScreenSave Changes and Exit Discard Changes and ExitInstall Operating System Support CD InformationRunning The Support CD Drivers Menu