ASRock K10N78hSLI-GLAN manual White end 2-pin

Page 25

Though this motherboard provides 24-pin ATX power connector, 12 it can still work if you adopt a traditional 20-pin ATX power supply. To use the 20-pin ATX power supply, please plug your power supply along with Pin 1 and Pin 13.

20-Pin ATX Power Supply Installation

1

24

13

ATX 12V Power Connector

(4-pin ATX12V1)

(see p.11, No. 2)

Please note that it is necessary to connect a power supply with ATX 12V plug to this connector. Failing to do so will cause power up failure.

Serial port Header

(9-pin COM1)

(see p.11 No.34)

1

RRXD1

DDTR#1

DDSR#1

CCTS#1

RRI#1

RRTS#1

GND

TTXD1

DDCD#1

This COM1 header

supports a serial port module.

HDMI_SPDIF Header

(3-pin HDMI_SPDIF1)

1

 

 

 

 

 

 

 

 

 

 

GND

(see p.11, No. 29)

 

+5V

 

 

 

SPDIFOUT

HDMI_SPDIF header, providing SPDIF audio output to HDMI VGA card, allows the system to connect HDMI Digital TV/ projector/LCD devices. Please connect the HDMI_SPDIF connector of HDMI VGA card to this header.

HDMI_SPDIF Cable

(Optional)

io

A. black end

+5V

 

 

 

 

SPDIFOUT

 

 

 

blue

 

 

 

GND

 

 

 

black

 

 

 

 

 

 

 

 

 

Please connect the black end (A)

C

of HDMI_SPDIF cable to the

BHDMI_SPDIF header on the

Amotherboard. Then connect the white end (B or C) of HDMI_SPDIF cable to the HDMI_SPDIF connector of HDMI VGA card.

B. white end (2-pin)

C. white end (3-pin)

SPDIFOUT

 

 

 

blue

SPDIFOUT

 

blue

GND

 

 

 

black

GND

 

black

 

 

 

 

 

 

25

Image 25
Contents K10N78hSLI-GLAN Disclaimer Copyright NoticeContents Software Support Bios Setup UtilityIntroduction Package ContentsSpecifications Unique Feature Bios FeatureSupport CD HardwarePage Page CPU DDR2 Motherboard LayoutTable for Audio Output Connection ASRock eSATAIISPDIF I/OPre-installation Precautions InstallationInstallation of CPU Fan and Heatsink CPU InstallationDual Channel Memory Configurations Installation of Memory Modules DimmNotch break Installing a DimmExpansion Slots PCI and PCI Express Slots Installing an expansion cardHybrid Slitm Operation Guide Minimum System Configuration for Hybrid SlitmSupported PCI Express Card for Hybrid Slitm Enjoy the benefit of Nvidia Hybrid Slitm PS2USBPW1 Jumpers SetupIDE1 Onboard Headers and ConnectorsSerial ATA Sata Power Cable Header CPU Fan Connector White end 2-pin Hdmispdif Header Connection Guide ESATAII Interface Introduction What is eSATAII?How to install eSATAII? Comparison between eSATAII and other devices Western Digital Sataii Hard Disk Setup GuidePage What is Hot Swap Function? What is Hot Plug Function?Points of attention, before you process the Hot Plug Sata / Sataii HDD Hot Plug Feature and Operation GuideHow to Hot Unplug a Sata / Sataii HDD How to Hot Plug a Sata / Sataii HDDInstalling Windows XP / XP 64-bit Without RAID Functions Driver Installation GuideMake a Sata / Sataii driver diskette Install Windows VistaTM / VistaTM 64-bit OS on your system Install Windows XP / XP 64-bit OS on your systemUse RAID Installation Guide to set RAID configuration Installing Windows XP / XP 64-bit With RAID Functions\ RAID Installation Guide \ I386 \ AHCIVista For Windows VistaTM OSSet the Sata Operation Mode option to RAID Untied Overclocking Technology Introduction Bios Menu BarMain Screen Navigation KeysTo jump to the Exit Screen or exit the current screen System Time HourMinuteSecondCPU Configuration Monitor Boot Security ExitAdvanced Screen MainBoot Failure Guard Overclock ModeAM2 Boost CPU Frequency MHzEnhanced Halt State Secure Virtual MachineProcessor Maximum Frequency North Bridge Maximum FrequencyProcessor Target Frequency Processor VoltageNorth Bridge Target Frequency CPU Frequency MultiplierFlexibility Option Memory Controller ModeCAS Latency CL CS/ODT Fine Delay Addr/Cmd Fine DelayMA Timing Bank InterleavingHybrid SLI Front PanelShare Memory Primary Graphics AdapterCPU NB Link Width CPU NB Link SpeedDram Voltage Chipset Core VoltageAcpi Configuration IDE Device Configuration Sata Operation ModeAcpi Hpet Table OnBoard IDE ControllerPIO Mode LBA/Large ModeDMA Mode Block Multi-Sector TransferPCI Latency Timer PCIPnP ConfigurationA.R.T 32Bit Data TransferSuper IO Configuration Floppy ConfigurationOnBoard Floppy Controller Serial Port AddressUSB Controller Enabled USB ConfigurationUSB Controller USB 2.0 SupportHardware Health Event Monitoring Screen Target CPU TemperatureCPU Quiet Fan Target Fan SpeedBoot Settings Configuration Boot ScreenBoot From Onboard LAN Boot Up Num-LockChange Supervisor Password Main Advanced Monitor BootSecurity Screen Exit Screen Load Optimal DefaultsSave Changes and Exit Discard Changes and ExitSupport CD Information Install Operating SystemRunning The Support CD Drivers Menu