ASRock K10N78hSLI-GLAN manual Boot Screen, Boot Settings Configuration, Boot From Onboard LAN

Page 57

3 . 5 Boot Screen

In this section, it will display the available devices on your system for you to config- ure the boot settings and the boot priority.

BIOS SETUP UTILITY

Main

Advanced

H/W Monitor

Boot

Security Exit

Boot Settings

Boot Settings Configuration

1st Boot Device

[1st Floppy Device]

2nd Boot Device

[HDD: PM-MAXTOR 6L08]

3rd Boot Device

[CD/DVD: SM-CD-ROM]

4th Boot Device

[USB]

Hard Disk Drives

 

Removable Drives

 

CD/DVD Drives

 

Configure Settings during System Boot.

 

Select Screen

 

Select Item

Enter

Go to Sub Screen

F1

General Help

F9

Load Defaults

F10

Save and Exit

ESC

Exit

v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.

3.5.1 Boot Settings Configuration

BIOS SETUP UTILITY

Boot

Boot Settings Configuration

Boot From Onboard LAN

[Disabled]

Bootup Num-Lock

[On]

To enable or disable the boot from network feature.

 

Select Screen

 

Select Item

+ -

Change Option

F1

General Help

F9

Load Defaults

F10

Save and Exit

ESC

Exit

v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.

Boot From Onboard LAN

Use this item to enable or disable the Boot From Onboard LAN feature.

Boot Up Num-Lock

If this item is set to [On], it will automatically activate the Numeric Lock function after boot-up.

57

Image 57
Contents K10N78hSLI-GLAN Disclaimer Copyright NoticeContents Software Support Bios Setup UtilityIntroduction Package ContentsSpecifications Unique Feature Bios FeatureSupport CD HardwarePage Page CPU DDR2 Motherboard LayoutTable for Audio Output Connection ASRock eSATAIISPDIF I/OPre-installation Precautions InstallationInstallation of CPU Fan and Heatsink CPU InstallationDual Channel Memory Configurations Installation of Memory Modules DimmNotch break Installing a DimmExpansion Slots PCI and PCI Express Slots Installing an expansion cardMinimum System Configuration for Hybrid Slitm Hybrid Slitm Operation GuideSupported PCI Express Card for Hybrid Slitm Enjoy the benefit of Nvidia Hybrid Slitm PS2USBPW1 Jumpers SetupIDE1 Onboard Headers and ConnectorsSerial ATA Sata Power Cable Header CPU Fan Connector White end 2-pin Hdmispdif Header Connection Guide ESATAII Interface Introduction What is eSATAII?How to install eSATAII? Comparison between eSATAII and other devices Western Digital Sataii Hard Disk Setup GuidePage What is Hot Swap Function? What is Hot Plug Function?Points of attention, before you process the Hot Plug Sata / Sataii HDD Hot Plug Feature and Operation GuideHow to Hot Unplug a Sata / Sataii HDD How to Hot Plug a Sata / Sataii HDDDriver Installation Guide Installing Windows XP / XP 64-bit Without RAID FunctionsMake a Sata / Sataii driver diskette Install Windows VistaTM / VistaTM 64-bit OS on your system Install Windows XP / XP 64-bit OS on your systemUse RAID Installation Guide to set RAID configuration Installing Windows XP / XP 64-bit With RAID Functions\ RAID Installation Guide \ I386 \ AHCIVista For Windows VistaTM OSSet the Sata Operation Mode option to RAID Untied Overclocking Technology Introduction Bios Menu BarMain Screen Navigation KeysTo jump to the Exit Screen or exit the current screen System Time HourMinuteSecondCPU Configuration Monitor Boot Security ExitAdvanced Screen MainBoot Failure Guard Overclock ModeAM2 Boost CPU Frequency MHzEnhanced Halt State Secure Virtual MachineProcessor Maximum Frequency North Bridge Maximum FrequencyProcessor Target Frequency Processor VoltageNorth Bridge Target Frequency CPU Frequency MultiplierMemory Controller Mode Flexibility OptionCAS Latency CL CS/ODT Fine Delay Addr/Cmd Fine DelayMA Timing Bank InterleavingHybrid SLI Front PanelShare Memory Primary Graphics AdapterCPU NB Link Width CPU NB Link SpeedDram Voltage Chipset Core VoltageAcpi Configuration IDE Device Configuration Sata Operation ModeAcpi Hpet Table OnBoard IDE ControllerPIO Mode LBA/Large ModeDMA Mode Block Multi-Sector TransferPCI Latency Timer PCIPnP ConfigurationA.R.T 32Bit Data TransferSuper IO Configuration Floppy ConfigurationOnBoard Floppy Controller Serial Port AddressUSB Controller Enabled USB ConfigurationUSB Controller USB 2.0 SupportHardware Health Event Monitoring Screen Target CPU TemperatureCPU Quiet Fan Target Fan SpeedBoot Settings Configuration Boot ScreenBoot From Onboard LAN Boot Up Num-LockMain Advanced Monitor Boot Change Supervisor PasswordSecurity Screen Exit Screen Load Optimal DefaultsSave Changes and Exit Discard Changes and ExitSupport CD Information Install Operating SystemRunning The Support CD Drivers Menu