Raypak 0133-4001 manual Inspection Procedures

Page 34

INSPECTION PROCEDURES

Inspect on the first and third month after initial start- up and then on an annual basis. If problems are found, refer to the Troubleshooting sections of this manual for additional directions.

1.Remove top of heater and inspect heat exchanger for soot and examine venting system.

2.Remove rear header and inspect for scale depos- its.

*3. Inspect pilot and main burner flame and firing rate.

*4. Inspect and operate all controls and gas valve.

*5. Visually inspect system for water leaks.

*6. a. Oil pump motor and bearing assembly, if oil cups are provided.

b.Disconnect pump from header and check condition of pump impeller. Check condition of bearing by attempting to move impeller from side to side. Replace any parts showing wear.

c.Check pump coupler for wear and vibration.

7.Check flow switch paddle.

8.Clean room air intake openings to assure adequate flow of combustion and ventilation air.

CAUTION: Combustion air must not be contaminated by corrosive chemical fumes which can damage the heater and void the warranty.

9.Keep heater area clear and free from combustible materials, gasoline, and other flammable vapors and liquids.

*Should be checked monthly. (Takes approximately 15 minutes).

Fig# 9336

PILOT BURNER FLAME-IID

(atmospheric units)

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Installation Operating Instructions For Your SafetyTable of Contents Model Identification General SpecificationsReceiving Equipment ALL Models Approved HOT Water Supply HeatersGeneral Safety Precautions Installation Instructions Installation CodesClearances Specifications and Dimensions ModelModels Models Outdoor Water Heaters High Wind Conditions Outdoor Units OnlyOutdoor Installations VentingIndoor Installations Before After Installation DrafthoodVent TERMINAL/INDOOR Stack Installation Vent Piping Fig. #7043.1Vent Damper Installation Models 133 Through 180 Where Required LocationVent Damper General PlumbingGAS Supply Connections GAS Pressure Regulator Venting of Diaphragm GAS ComponentsFlow Rates General Specifications UNI-TEMP 80 HOT Water Supply Systems Piping Domestic HOT Water Supply HeatersPiping Diagrams Type WH Unitemp 80 System Type NH Instantaneous Minimum Input Adjustment Type NH Dual ModelsElectronic Ignition Controls GeneralRelief Valve Economaster ControlHigh and LOW GAS Pressure Switches Optional Flow Switch100% Pilot Safety Limit Controls High LimitComponent Identification SINGLE-STAGE Tankstat Electrical ConnectionsON/OFF Units 400 WH1, WH2, WH3 LOW NOx WH1 Location of ControlsFig. #9334 Location of Controls START-UP Procedures Before START-UP Initial START-UP Pump and MotorTIME/TEMPERATURE Relationships in Scalds ScaldingTo Turn OFF GAS to Appliance For Your Safety Read Before OperatingOperating Instructions For Models with Manual GAS ValvesControls Inspection Procedures BurnersAfter START-UP For Models with Automatic GAS ValvesInspection Procedures START-UP Procedures Burner AdjustmentHigh GAS Pressure Switch Visual InspectionGAS Valve Removal Burner Tray RemovalPilot Removal Main Burner and Orifice RemovalTroubleshooting Electrical Honeywell S8600Wiring Diagrams Wiring Diagram WH2 182/260 Wiring Diagram WH2 330/400 Wiring Diagram WH2 514/624 Wiring Diagram WH2 Wiring Diagram WH2 Wiring Diagram WH2 Wiring Diagram WH2 Wiring Diagram WH1 181/261 LOW NOx Wiring Diagram WH1 331/401 LOW NOx Troubleshooting Mechanical Problem Possible Cause Corrective ActionService and Maintenance Procedures Troubleshooting PumpsTube Cleaning Heat Exchanger Removal Pilot Removal and CleaningHigh Limit or Tankstat Removal Typical Burner Tray IllustratedControl Well Replacement Heat Exchanger RE-ASSEMBLYTube Replacement Replacement Parts Cleaning Flue GAS PassagewaysCatalog Model Number Warranty Scope

0133-4001 specifications

Raypak 0133-4001 is a high-performance pool and spa heater designed for efficient and reliable heating. As part of Raypak's commitment to quality and innovation, this model combines advanced technologies and features to ensure optimal heating and energy efficiency.

One of the primary features of the Raypak 0133-4001 is its durable construction. Crafted from corrosion-resistant materials, this heater is built to withstand harsh weather conditions, ensuring longevity and minimal maintenance. This durability is particularly beneficial for outdoor installations, where exposure to the elements is a concern.

The Raypak 0133-4001 is equipped with a powerful heating capacity, making it suitable for both residential and commercial applications. With its robust output, it can quickly raise the temperature of a pool or spa, allowing for extended use even during cooler months. This rapid heating capability is complemented by its adjustable temperature settings, enabling users to customize their experience based on individual preferences.

Another significant characteristic of the Raypak 0133-4001 is its advanced digital control system. The intuitive interface allows for easy operation and precise temperature adjustments. Users can monitor settings and make adjustments with just a few button presses, ensuring convenience and usability. Additionally, this model often features built-in diagnostics, providing users with real-time feedback on the heater's performance and any necessary maintenance alerts.

Energy efficiency is a hallmark of the Raypak 0133-4001. This model is designed to minimize energy consumption while delivering maximum heating output. With its innovative heat exchanger technology, it optimizes the transfer of heat, reducing operational costs over time. This focus on energy efficiency not only benefits users financially but also promotes environmentally sustainable practices.

The Raypak 0133-4001 heater is compatible with a variety of pool and spa systems, making it a versatile choice for different setups. Its ease of installation and compatibility with standard plumbing connections simplify the integration process, whether for new installations or upgrades to existing systems.

In conclusion, the Raypak 0133-4001 is an excellent choice for those seeking a reliable, efficient, and user-friendly pool and spa heater. With its robust construction, powerful heating capabilities, advanced digital controls, and emphasis on energy efficiency, it stands out as a premier option in the market. Whether for residential or commercial use, the Raypak 0133-4001 is engineered to enhance the enjoyment and comfort of your swimming experience.
Top Page Image Contents