Maytag HXN4975S manual Gas Piping

Page 17

1/2 pound per square inch (3.5kPa), the damage to the gas control valve could result in a fire or explosion from leaking gas.

FIGURE19.

All vent gases must be completely vented to the outdoors of the structure (dwelling). Install only the draft hood provided with the new water heater and no other draft hood.

Vent pipes must be secured at each joint with sheet metal screws.

There must be a minimum of 6 inches (153 mm) clearance between single wall vent pipe and any combustible material. Fill and seal any clearance between single wall vent pipe and combustible material with mortar mix, cement, or other noncombustible substance. For other than single wall, follow vent pipe manufacturer’s clearance specifications. To insure a tight fit of the vent pipe in a brick chimney, seal around the vent pipe with mortar mix cement.

Failure to have required clearances between vent piping and combustible material will result in a fire hazard.

Be sure vent pipe is properly connected to prevent escape of dangerous flue gases which could cause deadly asphyxiation.

Chemical vapor corrosion of the flue and vent system may occur if air for combustion contains certain chemical vapors. Spray can propellants, cleaning solvents, refrigerator and air conditioner refrigerants, swimming pool chemicals, calcium and sodium chloride, waxes, bleach and process chemicals are typical compounds which are potentially corrosive.

Gas Piping

Make sure the gas supplied is the same type listed on the model rating plate. The inlet gas pressure must not exceed 14 inch water column (2.6kPa) for natural and propane (L.P.) gas. If the gas control valve is subjected to pressures exceeding

If the main gas line Shut-off serving all gas appliances is used, also turn “OFF” the gas at each appliance. Leave all gas appliances shut “OFF” until the water heater installation is complete.

A gas line of sufficient size must be run to the water heater. Consult the current edition of the CAN/CSA-B149.1, Installation Code and/or your gas supplier concerning pipe size.

There must be:

A readily accessible manual shut off valve in the gas supply line serving the water heater, and

A drip leg (sediment trap) ahead of the gas control valve to help prevent dirt and foreign materials from entering the gas control valve.

A flexible gas connector or a ground joint union between the shut off valve and control valve to permit servicing of the unit.

Be sure to check all the gas piping for leaks before lighting the water heater. Use a soapy water solution, not a match or open flame. Rinse off soapy solution and wipe dry.

The minimum inlet gas pressure shown on the rating plate is that which will permit firing at the rated input.

17

Image 17
Contents Series Nine Important Definitions Safe INSTALLATION, USE and ServiceSafety Precautions Table of Contents Customer Responsibilities Product SpecificationsAccessories Accessories and Tools NeededAdditional Tools Needed When Sweat Soldering ToolsRemoving the Old Water Heater Preparations for InstallationGET to Know Your Water Heater GAS Models Typical InstallationMixing Valve Usage Facts to Consider About the Location Locating and Installing the NEW Water HeaterInsulation Blankets ALL AIR from Inside Buildings See Figures 10 Water Piping Temperature-Pressure Relief Valve Filling the Water Heater Venting Gas Piping Sediment Traps GAS Piping with Flexible ConnectorOperating Instructions For Your Safety Read Before Lighting Temperature Time to Produce 2nd & 3rd Temperature RegulationTank Sediment Cleaning Service and MaintenanceBurner Cleaning Vent System InspectionHousekeeping Temperature-Pressure Relief Valve OperationAnode Rod Inspection DrainingDrain Valve Washer Replacement TroubleshootingService Start Up ConditionsSmoke / Odor Operational ConditionsLeakage Checkpoints Problem Cause Solution Troubleshooting GuideMaytag GAS Water Heaters Repair Parts ListPage Page Page Warranty Series Nine Avertissement INSTALLATION, Utilisation ET Entretien SécuritairesMesures DE Sécurité Table DES Matières Choix DE L’EMPLACEMENT DU CHAUFFE-EAU ET InstallationSpécifications Techniques DU Produit Responsabilité DU ClientAccessoires Accessoires ET Outils NécessairesOutils Outils supplémentaires requis pour la soudure à l’étainEnlèvement de l’ancien chauffe-eau Préparation À L’INSTALLATIONDescription DU CHAUFFE-EAU AU GAZ Installation TypeUtilisation D’UN Robinet Mélangeur Points à considérer dans le choix de l’emplacement Choix DE L’EMPLACEMENT DU CHAUFFE-EAU ET InstallationRevêtements isolants Air de combustion et air de ventilation en espace clos Air de combustion et air de ventilation en espace ouvertTuyauterie d’eau Soupape de décharge à sécurité thermique Remplissage du chauffe-eau Ventilation Tuyauterie de gaz Tuyauterie DE Gazavec Raccord Flexible Collecteur d’impuretésPage Pour Votre Sécurité Lisez Avant D’ALLUMER Réglage de la température Nettoyage du réservoir dépôts Entretien ET RéparationInspection du système de ventilation Inspection du brûleurVidange Entretien courantInspection de la tige d’anode Guide DE Dépannage Remplacement de la rondelle du robinet de vidangeSituations pouvant se produire à la mise en service Fumée et odeur Conditions de fonctionnementPoints de vérification des fuites Problème Cause Solution CHAUFFE-EAU AU GAZ Maytag Liste DES Pièces DE RechangePage Page Page Garantie

HXN4975S specifications

The Maytag HXN4975S is a state-of-the-art refrigerator that perfectly balances innovation, style, and functionality. Designed for modern kitchens, this model stands out with its stainless steel finish, which not only adds a sleek aesthetic but also ensures durability and resistance to fingerprints and smudges.

One of the standout features of the HXN4975S is its generous storage capacity. With multiple shelves and adjustable compartments, it provides ample space for groceries of all sizes. The fridge section includes spill-proof glass shelves that are easy to clean and prevent spills from cascading down to lower shelves, maintaining cleanliness effortlessly. Enhanced storage options like gallon door bins and humidity-controlled crisper drawers make it easy to store and organize a variety of items.

The HXN4975S is equipped with advanced cooling technologies. Its dual cooling system ensures optimal temperature and humidity levels, keeping your food fresh longer. This technology separates the airflow between the refrigerator and freezer, preventing the transfer of odors and maintaining the quality of stored food. Additionally, the refrigerator incorporates a powerful compressor that efficiently maintains the desired temperatures while reducing energy consumption.

Another key feature of the Maytag HXN4975S is its smart connectivity. With built-in Wi-Fi, users can control their refrigerator remotely through a compatible smartphone app. This feature allows for adjustments to be made on-the-go, enabling users to monitor temperatures, receive alerts, and even diagnose issues without the need for a technician.

Energy efficiency is also a priority for the HXN4975S, as it is ENERGY STAR rated. This ensures that the refrigerator not only saves on energy bills but also contributes to a greener environment. The LED lighting inside the unit provides bright illumination while consuming minimal energy, allowing for excellent visibility regardless of the time of day.

The Maytag HXN4975S also focuses on user-friendly features, such as its intuitive temperature control and ice and water dispenser located conveniently on the front door. The sleek design incorporates a filtered water system, providing clean and safe drinking water instantly.

Overall, the Maytag HXN4975S embodies a commitment to quality and efficiency, catering to the needs of busy families while enhancing the kitchen's functionality and style. This refrigerator truly stands out as a reliable appliance designed with both performance and user experience in mind.