Maytag HXN4975S Troubleshooting, Drain Valve Washer Replacement, Service, Start Up Conditions

Page 24

OPEN a nearby hot water faucet and leave open to allow for draining.

Connect a hose to the drain valve and terminate to an adequate drain.

OPEN the water heater drain valve to allow for tank draining.

NOTE: If the water heater is going to be shut down and drained for an extended period, the drain valve should be left open with hose connected allowing water to terminate to an adequate drain.

CLOSE the drain valve.

Follow instructions in the Filling The Water heater section.

Follow the lighting instructions in the Lighting section to restart the water heater.

Drain Valve Washer Replacement

(for selected models with plastic drain valves) (See Figure 26)

NOTE: For ordering replacement washers, refer to the “Repair Parts List” section of this manual.

Turn “OFF” gas supply to water heater.

Follow “Draining” instructions.

Turning counter clockwise ( ), remove the hex cap below the screw handle.

Remove the washer and put the new one in place.

Screw the handle and cap assembly back into the drain valve and retighten using a wrench. DO NOT OVER TIGHTEN.

Follow instructions in the Filling The Water Heater section.

Check for leaks.

Follow the lighting instructions in the Lighting section to restart the water heater.

FIGURE 26.

Service

Before calling for repair service, read the Start Up Conditions and Operational Conditions found in the Troubleshooting Guide of this manual.

If a condition persists or you are uncertain about the operation of the water heater, let the Maytag Customer Service Center check it out.

Call the Maytag Customer Service at 1-800-788-8899 for an authorized servicer.

TROUBLESHOOTING

Start Up Conditions

Draft Hood Operation

Check draft hood operation by performing a worst case depressurization of the building. With all doors and windows closed, and with all air handling equipment and exhaust fans operating, such as furnaces, clothes dryers, range hoods and bathroom fans, a match flame should still be drawn into the draft hood of the water heater with its burner firing. If the flame is not drawn toward the draft hood, shut off the water heater and make necessary air supply changes to correct.

Condensation

Whenever the water heater is filled with cold water, some condensate will form while the burner is on. A water heater may appear to be leaking when in fact the water is condensation. This usually happens when:

A new water heater is filled with cold water for the first time.

Burning gas produces water vapor in water heaters, particularly high efficiency models where flue temperatures are lower.

Large amounts of hot water are used in a short time and the refill water in the tank is very cold.

Moisture from the products of combustion condense on the cooler tank surfaces and form drops of water which may fall onto the burner or other hot surfaces to produce a “sizzling” or “frying” noise.

Excessive condensation can cause pilot outage due to water running down the flue tube onto the main burner and putting out the pilot.

Because of the suddenness and amount of water, condensation water may be diagnosed as a “tank leak”. After the water in the tank warms up (about 1-2 hours), the condition should disappear.

Do not assume the water heater is leaking until there has been enough time for the water in the tank to warm up.

An undersized water heater will cause more condensation. The water heater must be sized properly to meet the family’s demands for hot water including dishwashers, washing machines and shower heads.

Excessive condensation may be noticed during the winter and early spring months when incoming water temperatures are at their lowest.

24

Image 24
Contents Series Nine Safe INSTALLATION, USE and Service Important DefinitionsSafety Precautions Table of Contents Product Specifications Customer ResponsibilitiesAccessories and Tools Needed AccessoriesAdditional Tools Needed When Sweat Soldering ToolsPreparations for Installation Removing the Old Water HeaterTypical Installation GET to Know Your Water Heater GAS ModelsMixing Valve Usage Locating and Installing the NEW Water Heater Facts to Consider About the LocationInsulation Blankets ALL AIR from Inside Buildings See Figures 10 Water Piping Temperature-Pressure Relief Valve Filling the Water Heater Venting Gas Piping GAS Piping with Flexible Connector Sediment TrapsOperating Instructions For Your Safety Read Before Lighting Temperature Regulation Temperature Time to Produce 2nd & 3rdService and Maintenance Tank Sediment CleaningBurner Cleaning Vent System InspectionTemperature-Pressure Relief Valve Operation HousekeepingAnode Rod Inspection DrainingTroubleshooting Drain Valve Washer ReplacementService Start Up ConditionsOperational Conditions Smoke / OdorLeakage Checkpoints Troubleshooting Guide Problem Cause SolutionRepair Parts List Maytag GAS Water HeatersPage Page Page Warranty Series Nine INSTALLATION, Utilisation ET Entretien Sécuritaires AvertissementMesures DE Sécurité Choix DE L’EMPLACEMENT DU CHAUFFE-EAU ET Installation Table DES MatièresResponsabilité DU Client Spécifications Techniques DU ProduitAccessoires ET Outils Nécessaires AccessoiresOutils Outils supplémentaires requis pour la soudure à l’étainPréparation À L’INSTALLATION Enlèvement de l’ancien chauffe-eauInstallation Type Description DU CHAUFFE-EAU AU GAZUtilisation D’UN Robinet Mélangeur Choix DE L’EMPLACEMENT DU CHAUFFE-EAU ET Installation Points à considérer dans le choix de l’emplacementRevêtements isolants Air de combustion et air de ventilation en espace ouvert Air de combustion et air de ventilation en espace closTuyauterie d’eau Soupape de décharge à sécurité thermique Remplissage du chauffe-eau Ventilation Tuyauterie de gaz Collecteur d’impuretés Tuyauterie DE Gazavec Raccord FlexiblePage Pour Votre Sécurité Lisez Avant D’ALLUMER Réglage de la température Entretien ET Réparation Nettoyage du réservoir dépôtsInspection du système de ventilation Inspection du brûleurEntretien courant Inspection de la tige d’anodeVidange Remplacement de la rondelle du robinet de vidange Situations pouvant se produire à la mise en serviceGuide DE Dépannage Conditions de fonctionnement Fumée et odeurPoints de vérification des fuites Problème Cause Solution Liste DES Pièces DE Rechange CHAUFFE-EAU AU GAZ MaytagPage Page Page Garantie

HXN4975S specifications

The Maytag HXN4975S is a state-of-the-art refrigerator that perfectly balances innovation, style, and functionality. Designed for modern kitchens, this model stands out with its stainless steel finish, which not only adds a sleek aesthetic but also ensures durability and resistance to fingerprints and smudges.

One of the standout features of the HXN4975S is its generous storage capacity. With multiple shelves and adjustable compartments, it provides ample space for groceries of all sizes. The fridge section includes spill-proof glass shelves that are easy to clean and prevent spills from cascading down to lower shelves, maintaining cleanliness effortlessly. Enhanced storage options like gallon door bins and humidity-controlled crisper drawers make it easy to store and organize a variety of items.

The HXN4975S is equipped with advanced cooling technologies. Its dual cooling system ensures optimal temperature and humidity levels, keeping your food fresh longer. This technology separates the airflow between the refrigerator and freezer, preventing the transfer of odors and maintaining the quality of stored food. Additionally, the refrigerator incorporates a powerful compressor that efficiently maintains the desired temperatures while reducing energy consumption.

Another key feature of the Maytag HXN4975S is its smart connectivity. With built-in Wi-Fi, users can control their refrigerator remotely through a compatible smartphone app. This feature allows for adjustments to be made on-the-go, enabling users to monitor temperatures, receive alerts, and even diagnose issues without the need for a technician.

Energy efficiency is also a priority for the HXN4975S, as it is ENERGY STAR rated. This ensures that the refrigerator not only saves on energy bills but also contributes to a greener environment. The LED lighting inside the unit provides bright illumination while consuming minimal energy, allowing for excellent visibility regardless of the time of day.

The Maytag HXN4975S also focuses on user-friendly features, such as its intuitive temperature control and ice and water dispenser located conveniently on the front door. The sleek design incorporates a filtered water system, providing clean and safe drinking water instantly.

Overall, the Maytag HXN4975S embodies a commitment to quality and efficiency, catering to the needs of busy families while enhancing the kitchen's functionality and style. This refrigerator truly stands out as a reliable appliance designed with both performance and user experience in mind.