Maytag HN41240X, HN51240X Troubleshooting, Start Up Conditions, Smoke/Odor, Thermal Expansion

Page 25

Troubleshooting

Start Up Conditions

CONDENSATION

Whenever the water heater is filled with cold water, a certain amount of condensation will form while the burner is on. A water heater may appear to be leaking when in Fact the water is condensation. This usually happens when:

"When a new water heater is filled with cold water for the first time.

•When gas burns and water vapor is produced in water heaters, particularly high efficiency models where flue

temperatures are lower.

•When you use large amounts of hot water in a short time and the refill water is very cold.

Moisture from the products of combustion condense on the cooler tank surfaces and form drops of water which may fall onto the burner or other hot surfaces to produce a "sizzling" or

"frying" noise.

Excessive condensation can cause pilot outage due to water

running down the flue tube onto the main burner and putting out the pilot,

Because of the suddenness and amount of water, condensation water may be diagnosed as a "tank leak". After the water in the tank warms up (about 1-2 hours), the condition should disap-

pear.

Do not assume the water heater is leaking until there has been enough time for the water in the tank to warm up.

An undersized water heater will cause more condensation. The water heater must be sized properly to meet the family's

demands for hot water including dishwashers, washing machines and shower heads.

Excessive condensation may be noticed during the winter and

early spring months when incoming water temperatures are at their lowest.

Good venting is essential for a gas fired water heater to oper- ate properly as well as to carry away products of combustion and water vapor.

SMOKE/ODOR

It is not uncommon to experience a small amount of smoke and odor during the initial start-up. This is due to burning off ofoil from metal parts, and will disappear in a short while.

THERMAL EXPANSION

Water supply systems may, because of high line pressure, fre- quent cut-offs,the effects of water hammer and others, have installed devices such as pressure reducing valves, check valves, back flow preventers, etc. to control these types of problems. When these devices are not equipped with an inter- nal by-pass,and no other measures are taken, the devices cause the water system to be closed. As water is heated, it

expands (thermal expansion) and closed systems do not allow for the expansion of heated water.

The water within the water heater tank expands as it is heated

and increases the pressure of the water system. If the relieving

point of the water heater's temperature-pressure relief valve is reached, the valve wiI1 relieve the excess pressure. The tem-

perature-pressure relief valve is not intended for the con- stant relief of thermal expansion. This is an unacceptable condition and must be corrected.

It is recommended that any devices installed which cotdd create a closed system have a by-pass and/or the system have an expansion tank to refieve the pressure built by thermal expan- sion in the water system. Expansion tanks are available for ordering through Maytag Customer Service (1-800-788-8899). Contact the local plumbing inspector, water supplier, and/or call Maytag Customer Service at 1-800-788-8899 for an authorized servicer for assistance in controlling these situations.

STRANGE SOUNDS

Possible noises due to expansion and contraction of some metal parts during periods of heat-up and cool-down do not represent harmful or dangerous conditions.

Condensation causes sizzling and popping with the burner area during heating and cooling periods and should be consid- ered normal. See "Condensation" section.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents 1VIAYIAG Awarning Safety Instructions3Safety Instructions on Safety InstructionsPremises Acaution Safety InstructionsTable of Contents Customer Information Product SpecificationsAccessories Accessoriesand Tools Needed1hewater passingout may Instructions for InstallationThan normalandthisresidue,if spilledout,couldcausestaining Watertemper Outletd Mixingvalve Instructions for Installation contdReliefvalve Locating the New Water Heater Instructions for Installation contdTopview Withoutdoor OfclosetCombustion Air and Ventilation Locating NewHeater Contd For Appliances Located Unconfined Spaces For /ppllances Located Confined =pacesIFigure3I Instructions for Installation contdHotter TemperatureThreadedto SweatcouplingShutoff Temperature-Pressure Relief ValveOLD PressureDrafthood Filling the Water HeaterVenttooutdoorsor Drafted ChimneyPerlinearfoot Vent PipeinstallationChemical vapor corrosion of re flue and vent sys Tested before placing the appliance in operationGAS Piping with Flexible ConnectorGassupplypiping ManualInstallation Checklist Lighting Instructions for OperationSTOPReadthesafetyinformationaboveonthislabel Servicete chnicianForceorattemptedrepairThepilotislit , Releaseknobanditwillpopbackup Immediatelycallyourservicetechnicianor gasInstructions for Operation contd Temperature RegulationTurn OFF the manualgascontrolvalve to the appliance OUS Bodily Injury or Property Damage Service and MaintenanceBe sure Vent Erly Connected to Prevent Gasses which Could cause deadly AsphyxiationGasControl Valve & Burner Assembly Replacement Information Service and Maintenance contdBurner Cleaning Handlassemblyand CAP Washer Temperature-Pressure Relief Drain Valve WasherHousekeeping DischargepipeStart Up Conditions TroubleshootingSMOKE/ODOR Thermal ExpansionAIR in HOT Water Faucets Awarning Troubleshooting contdOperational Conditions contd KCAUTION Leakage CheckpointsETC Repair Parts ListETC5× Model Numbers Repair Parts List contdOdel Numbers KEY Repair Parts List contdHN41240X HN51240X HP41240X HP51240X HN41250X HN51250X Part Descripti on Part NumbersRepair Parts List contd Part Description Part Numbers Model Numbers KEY16 //i MOD EL Numbers KEY 660 0 110 Warranty0002 9164

HN41240X, HN51240X specifications

The Maytag HN51240X and HN41240X are two reliable and efficient washers, offering exceptional performance for those seeking durability and functionality in their laundry routines. These models are designed with a blend of innovative technologies and user-friendly features, making them standout options in the semi-professional segment.

The HN51240X comes equipped with a powerful motor that provides impressive wash action without compromising on efficiency. Its high-capacity drum allows users to tackle large loads easily, perfect for families or individuals with significant laundry needs. Meanwhile, the HN41240X, although slightly smaller, still boasts an impressive capacity that ensures thorough cleaning and better water usage.

Both models feature Maytag’s exclusive PowerWash cycle, which is engineered to tackle tough stains by combining extra agitation, water, and heat. This results in clothes coming out cleaner, even when dealing with heavy soil and grime. Additionally, they utilize the Advanced Moisture Sensing technology that detects moisture levels and adjusts drying time accordingly, preventing over-drying and preserving fabric quality.

The construction of the HN51240X and HN41240X emphasizes durability. Their robust design includes a stainless steel wash basket and a solid, heavy-duty frame, which not only helps reduce vibrations during operation but also ensures long-lasting performance. The machines are designed to withstand the rigors of daily use while maintaining their efficiency and effectiveness.

Another notable characteristic of these models is their energy efficiency. They are ENERGY STAR certified, meaning they meet strict energy efficiency guidelines set by the Environmental Protection Agency. This leads to lower energy bills while still delivering the performance and cleaning power users expect from a Maytag appliance.

For added convenience, both washers feature a variety of wash cycles and options, allowing users to customize their laundry experience. From delicate fabrics to bulky bedding, there is a setting suitable for every type of load. Their intuitive controls make operation straightforward, perfect for users of all experience levels.

In summary, the Maytag HN51240X and HN41240X stand out as quality washing machines that combine innovative technology with user-centric design features. They are perfect for those who value efficiency, durability, and powerful cleaning capabilities in their laundry appliances.
Top Page Image Contents