Maytag HN51240X, HN41240X manual Leakage Checkpoints, Kcaution

Page 28

Troubleshooting (cont'd)

Leakage Checkpoints

Use this guide to check a "Leaking" water heater. Many sus-

pected"Leakers" arenot leaking tanks. Often the sourceof the water can be found and corrected,

If you are not thoroughly familiar with your local gas codes your water heater, and safety practices, contact your local gas

utifity or call Maytag Customer Service at 1-800-788-8899 for an authorized servicer to check the water heater.

_i CAUTION

]

Read this manual first. Then before checkingthe water heater make sure the gas supply hasbeen ] turned HOFF", and never turn the gas HOW'before

the tank s completely full of water.

_kCAUTION

Never use this water heater unless it is completely [

filled with water. Toprevent damage to the tank, I the tank must be filledwith water. Water must flow from the hot water faucet before turning "ON" gas

to the water heater.

I

densed out of the combustion products. This is caused by

a problem in the vent. Call Maytag Customer Service at 1-800-788-8899 for an authorized servicer.

O*Condensation may be seen on pipes in humid weather or pipe connections may be leaking.

O'The

primary anode rod fitting

may be leaking.

_

Water

at the draft hood is water

vapor which has con-

OSmafi amounts of water from temperature-pressurerelief valve may be due to thermal expansion or high water

pressure in your area.

O* The temperature-pressure relief valve may be leaking at the tank fitting.

OWater from a drain valve may be due to the valve opened slightly.

O'The drain valve may be leaking at the tank fitting.

Combustion products contain water vapor which can condense on the cooler surfaces of the tank. Droplets

form and drip into the fire or run on the floor. This is common at the time ofstartup after installation and

when incoming water is cold.

OWater in the water heater bottom or on the floor may be from condensation, loose connections, or the relief valve.

DO NOT replace the water heater until a full inspection of all possible water sources is made and necessary cor- rective steps taken. Leakage from other appliances, water lines, or ground seepage should also be checked.

O

*NOTE:To check where threaded portion enters tank,

 

insert cotton swab between jacket opening and fitting. If

 

cotton is wet, follow "Draining" instructions in the

 

"Service and Maintenance" section and then remove fit-

 

ring. Put pipe

dope or teflon tape on the threads

and

 

replace. Then

follow "Filling the Water Heater"

instruc-

 

tions in the "Instructions for Installation" section.

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents 1VIAYIAG Safety Instructions Awarning3Safety Instructions on Safety InstructionsPremises Safety Instructions AcautionTable of Contents Product Specifications Customer InformationAccessoriesand Tools Needed Accessories1hewater passingout may Instructions for InstallationThan normalandthisresidue,if spilledout,couldcausestaining Watertemper Outletd Mixingvalve Instructions for Installation contdReliefvalve Instructions for Installation contd Locating the New Water HeaterTopview Withoutdoor OfclosetLocating New Combustion Air and VentilationHeater Contd For Appliances Located Unconfined Spaces For /ppllances Located Confined =pacesInstructions for Installation contd IFigure3ITemperature HotterThreadedto SweatcouplingTemperature-Pressure Relief Valve ShutoffOLD PressureFilling the Water Heater DrafthoodVenttooutdoorsor Drafted ChimneyVent Pipeinstallation PerlinearfootChemical vapor corrosion of re flue and vent sys Tested before placing the appliance in operationFlexible Connector GAS Piping withGassupplypiping ManualInstallation Checklist Instructions for Operation LightingServicete chnicianForceorattemptedrepair STOPReadthesafetyinformationaboveonthislabelThepilotislit , Releaseknobanditwillpopbackup Immediatelycallyourservicetechnicianor gasInstructions for Operation contd Temperature RegulationTurn OFF the manualgascontrolvalve to the appliance Service and Maintenance OUS Bodily Injury or Property DamageBe sure Vent Erly Connected to Prevent Gasses which Could cause deadly AsphyxiationGasControl Valve & Burner Assembly Replacement Information Service and Maintenance contdBurner Cleaning Temperature-Pressure Relief Drain Valve Washer Handlassemblyand CAP WasherHousekeeping DischargepipeTroubleshooting Start Up ConditionsSMOKE/ODOR Thermal ExpansionTroubleshooting contd AIR in HOT Water Faucets AwarningOperational Conditions contd Leakage Checkpoints KCAUTIONETC Repair Parts ListETC5× Repair Parts List contd Model NumbersRepair Parts List contd Odel Numbers KEYHN41240X HN51240X HP41240X HP51240X HN41250X HN51250X Part Descripti on Part NumbersRepair Parts List contd Model Numbers KEY Part Description Part Numbers16 //i MOD EL Numbers KEY 660 0 110 Warranty0002 9164

HN41240X, HN51240X specifications

The Maytag HN51240X and HN41240X are two reliable and efficient washers, offering exceptional performance for those seeking durability and functionality in their laundry routines. These models are designed with a blend of innovative technologies and user-friendly features, making them standout options in the semi-professional segment.

The HN51240X comes equipped with a powerful motor that provides impressive wash action without compromising on efficiency. Its high-capacity drum allows users to tackle large loads easily, perfect for families or individuals with significant laundry needs. Meanwhile, the HN41240X, although slightly smaller, still boasts an impressive capacity that ensures thorough cleaning and better water usage.

Both models feature Maytag’s exclusive PowerWash cycle, which is engineered to tackle tough stains by combining extra agitation, water, and heat. This results in clothes coming out cleaner, even when dealing with heavy soil and grime. Additionally, they utilize the Advanced Moisture Sensing technology that detects moisture levels and adjusts drying time accordingly, preventing over-drying and preserving fabric quality.

The construction of the HN51240X and HN41240X emphasizes durability. Their robust design includes a stainless steel wash basket and a solid, heavy-duty frame, which not only helps reduce vibrations during operation but also ensures long-lasting performance. The machines are designed to withstand the rigors of daily use while maintaining their efficiency and effectiveness.

Another notable characteristic of these models is their energy efficiency. They are ENERGY STAR certified, meaning they meet strict energy efficiency guidelines set by the Environmental Protection Agency. This leads to lower energy bills while still delivering the performance and cleaning power users expect from a Maytag appliance.

For added convenience, both washers feature a variety of wash cycles and options, allowing users to customize their laundry experience. From delicate fabrics to bulky bedding, there is a setting suitable for every type of load. Their intuitive controls make operation straightforward, perfect for users of all experience levels.

In summary, the Maytag HN51240X and HN41240X stand out as quality washing machines that combine innovative technology with user-centric design features. They are perfect for those who value efficiency, durability, and powerful cleaning capabilities in their laundry appliances.
Top Page Image Contents