Johnson Controls J15 warranty Field-Installedaccessories, Control Options

Page 7
CONTROL OPTIONS

349687-JTG-A-1007

 

• SMOKE DETECTORS - (supply air & return air) The

• Johnson UNT 1126 Rooftop Controller - N2 protocol

smoke detectors stop operation of the unit by interrupting

with air proving and dirty filter sensors. Hardware con-

power to the control board if smoke is detected within the

tains generic application logic; field engineering and/or

air compartment.

modification may be required.

Factory installed smoke detectors in the return air may be subjected to freezing temperatures during “off” times due to outside air infiltration. These smoke detectors have an operation limit of 32°F to 131°F. Smoke detectors installed in areas that could be outside those limitations will have to be moved to prevent having false alarms.

•COIL GUARD - Customers can purchase a coil guard kit to protect the condenser coil from damage. This is not a hail guard kit.

•STAINLESS STEEL HEAT EXCHANGER - For applica- tions in corrosive environments, this option provides a full stainless steel heat exchanger assembly.

•STAINLESS STEEL DRAIN PAN - An optional rust-proof stainless steel drain pan is available to provide years of trouble-free operation in corrosive environments.

•PHASE MONITORS - Designed to prevent unit damage. The phase monitor will shut the unit down in an out-of- phase condition.

•HIGH STATIC DRIVE - Includes a belt and blower pulley upgrade to enhance blower performance.

•DIRTY FILTER SWITCH - This kit includes a differential pressure switch that energizes the fault light on the unit thermostat, indicating that there is an abnormally high pressure drop across the filters. Factory installed option or field installed accessory.

•HINGED FILTER DOOR/”TOOL FREE” BLOWER AND ACCESS PANELS (not hinged) - This option allows for easy access and maintenance.

NOTE:Knobs are shipped separately within the unit to prevent shipping damage. These must be field installed for tool free operation.

•HINGED/"TOOL FREE" BLOWER, BLOWER MOTOR, FILTER AND ELECTRIC ACCESS PANELS - This option allows for complete hinged and tool free access to the unit's blower, blower motor, filters and electrical panel sections.

CONTROL OPTIONS

•Johnson Light Commercial System (LCCS) - Provides rooftop system integration for LCCS single zone, change-over bypass and VAV systems.

FIELD-INSTALLED ACCESSORIES

•SINGLE INPUT ELECTRONIC ENTHALPY ECONO- MIZERS - Includes a slide-in /plug-in damper assembly with fully modulating spring-return motor actuator capa- ble of introducing up to 100% outdoor air with nominal 1% leakage type dampers.

The enthalpy system contains one sensor that monitors the outdoor air and determines when the air is cool enough and dry enough to provide free cooling.

The rainhood is painted to match the basic unit and must be field-assembled before installing.

•MOTORIZED OUTDOOR AIR INTAKE DAMPER - Includes a slide-in /plug-in damper assembly with a 2- position, spring return motor actuator which opens to some pre-set position whenever the supply air blower is operating and will drive fully closed when the blower unit shuts down.

The rain hood is painted to match the basic unit and must be field assembled before installing.

•ROOF CURBS - Fourteen-inch high roof curbs provide a water-tight seal between the unit and the finished roof. These full perimeter curbs meet the requirements of the National Roofing Contractors Association (NRCA) and are shipped knocked-down for field assembly.

They're designed to fit inside the base rails of the unit and include both a wood nailing strip and duct hanger supports.

•HIGH ALTITUDE NATURAL GAS - Burner orifices and pilot orifices are provided for proper furnace operation at altitudes up to 6,000 feet.

•PROPANE - Burner orifices, pilot orifices and gas valve parts are provided to convert a natural gas furnace to propane.

•HIGH ALTITUDE PROPANE - Burner orifices and pilot orifices are provided for proper furnace operation at alti- tudes up to 6,000 feet. This accessory supplements the basic propane conversion kit.

•SIDE DUCT FLANGES - One-inch flanges replace the supply and return air panels on the rear of the unit to accommodate horizontal duct connections. These flanges can also be used individually for bottom supply/ horizontal return or horizontal supply/bottom return. They cannot be used on units with power exhaust.

•BAROMETRIC RELIEF DAMPER - This damper acces- sory can be used to relieve internal building air pressure on units with an economizer without power exhaust. This

Johnson Controls Unitary Products

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents TECHNICAL GUIDE SERIES SINGLE PACKAGE GAS/ELECTRIC UNITSAND SINGLE PACKAGE AIR CONDITIONERS DESCRIPTIONLIST OF FIGURES TABLE OF CONTENTSLIST OF TABLES 15-25Ton Series 20 Model Number Nomenclature PRODUCT NOMENCLATUREJ15 D J N24 A 2 A AA 1 0 1 2 4 A FEATURES FIGURE 1 - UNIT CUTAWAY FACTORY-INSTALLEDOPTIONS349687-JTG-A-1007 CONTROL OPTIONS FIELD-INSTALLEDACCESSORIES349687-JTG-A-1007 TABLE 2 CAPACITY RATINGS - ARI TABLE 1 SOUND POWER RATING1TABLE 3 GAS HEAT RATIINGS TABLE 4 COOLING CAPACITIES FOR J15DJ TABLE 5 COOLING CAPACITIES FOR J18DJ TABLE 6 COOLING CAPACITIES FOR J20DJ TABLE 7 COOLING CAPACITIES FOR J25DJ TABLE 8 ALTITUDE CORRECTION FACTORS Johnson Controls Unitary Products FIGURE 2 - ALTITUDE/TEMPERATURE CONVERSION FACTORVOLT AND 208 VOLT AND STANDARD DRIVE208 VOLT AND HIGH STATIC DRIVE 230/460/575208 VOLT AND 208 VOLT ANDSTANDARD DRIVEVOLT AND 208 VOLT AND STANDARD DRIVE208 VOLT AND HIGH STATIC DRIVE 230/460/575VOLT AND 208 VOLT AND STANDARD DRIVE208 VOLT AND HIGH STATIC DRIVE 230/460/575208 VOLT AND 208 VOLT ANDSTANDARD DRIVEVOLT AND 208 VOLT AND STANDARD DRIVE208 VOLT AND HIGH STATIC DRIVE 230/460/575VOLT AND 208 VOLT AND STANDARD DRIVE208 VOLT AND HIGH STATIC DRIVE 230/460/575TABLE 16 BLOWER MOTOR AND DRIVE DATA TABLE 18 POWER EXHAUST PERFORMANCETABLE 17 STATIC RESISTANCES1 COMPRESSORS Johnson Controls Unitary Products NOTE 1 HACR Type per NECNOTE 1 HACR Type per NEC 349687-JTG-A-1007Johnson Controls Unitary Products NOTE 1 HACR Type per NECJ15DJ TABLE 21 J**DJ VOLTAGE LIMITATIONS1TABLE 22 PHYSICAL DATA MODELSFIGURE 3 - TYPICAL J**DJ FIELD WIRING DIAGRAM TABLE 23 SUPPLY FAN VFD WEIGHTS, IN LBSTABLE 24 ELECTRIC HEAT CORRECTION FACTORS USED FOR FIGURE 4 - FRONT VIEW DIMENSIONSTABLE 25 UTILITIES ENTRY DATA HOLEduct flange openings see FIGURE 5 - REAR VIEW DIMENSIONSDimensions listed are for side Field Accessories for SideTABLE 26 MINIMUM CLEARANCES SLAB ON GROUND INSTALLATION FIGURE 7 - UNIT CENTER OF GRAVITYFIGURE 8 - TYPICAL UNIT APPLICATIONS ROOF JACK INSTALLATION ROOF CURB INSTALLATION4 Point Loads lbs FIGURE 9 - FOUR AND SIX POINT LOADSTABLE 27 FOUR AND SIX POINT LOADS TotalFIGURE 11 - ROOF CURB DUCT OPENINGS DIMENSION FIGURE 10 - UNIT ROOF CURB DIMENSIONSFIGURE 12 - CUT AWAY OF ROOF CURB Page GENERAL GUIDE SPECIFICATIONSDESCRIPTION GAS HEATING SECTION J**DJN MODELS OUTDOOR CONDENSER FAN ASSEMBLYREFRIGERANT COMPONENTS UNIT CONTROLSSTANDARD LIMITED WARRANTIES UNIT OPERATING CHARACTERISTICSELECTRIC HEATING J**DJC/E MODELS ELECTRICAL REQUIREMENTSOTHER PRE-ENGINEEREDACCESSORIES AVAILABLE
Top Page Image Contents