Heath Zenith 598-1306-02 manual Floodlight, Lamp Modes, Features and Ratings, Gasket Mounting Bolt

Page 8

Floodlight

Features and Ratings:

• Up to 150 Watt maximum incandescent load or 240 Watt maximum halogen load (up to 75 Watt maximum incandescent,

or 120 Watt maximum halogen, per lampholder).

•Minimal wiring required.

•Install fixture in accordance with local codes.

Lamp Modes

There are three lamp modes (light turn-on effects) available when motion is detected:

•NORMAL or - Light instantly comes on.

•SOFT - Light starts dim and gradually increases to full brightness. Light gradually dims to half-bright, pauses, and then continues dimming to off when motion is no longer detected and after selected ON-TIME.

•FLASH - Light flashes on then off twice before turning on full brightness.

WARNING: Turn power off at the fuse or circuit breaker.

1.Remove the existing light fixture.

2.Install the mounting strap as shown using two screws that fit your junction box.

Note: The plastic hanger can be used to hold the fixture while wiring. Thread the small end of the plastic hanger through the hole in the center of the cover plate. Insert the small end into one of the slots on the mounting strap.

3.Set the LAMP MODE switch to the desired light turn-on effect (Normal, Soft, Flash).

4.Route the wires from the light receiver through the large gasket holes.

5.Twist the junction box wires and fixture wires together as shown.

Secure with UL approved wire connectors.

6.Align the cover plate and cover plate gasket. Secure with mounting bolt.

7.Push the rubber plug firmly into place.

8.Not intended for waterproof junction boxes. Fixture should be surface mount only. Caulk the wall plate mounting surface with silicone weather sealant.

9.Adjust the lamp holders by loosening the lock nuts. Note: Do not rotate the lamp holders more than 180° from the factory setting.

Caution: To avoid water damage and electrical shock, keep lamp holders 30° below horizontal.

10.Screw incandescent bulb up to rated wattage into module. When screwing in the lamps, do not overtighten.

Caution: Do not exceed the maximum load limits listed above.

11.Check operation. Activate transmitter being used with receiver (see transmitter instructions).Asignal will be sent to the receiver to turn the receiver ON or OFF.

WARNING: Risk of fire. Do not aim the lamps at a combustible surface within 3 ft. (1 m).

Mounting

White to

 

Black to

Rubber

Strap

 

White

 

Black

 

 

Plug

 

 

 

 

 

 

 

 

Gasket Mounting

Bolt

Junction box ground wire to green

ground screw on fixture.

Wiring Floodlight

598-1306-02

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Features Code SettingsExample 1 Code Settings, System Example 2 Code Settings, SystemCode Switch Locations Code SwitchesWall Switch Receiver Floodlight Motion SensorSelect Night or 24 Hour Mode Installing BatteriesInstalling Motion Sensor 240 Motion SensorsMotion Sensor Controls Check Operation and AdjustmentDualBrite Dimmer Control 240 180 Motion SensorMotion Sensor Coverage Area Wall Switch Receiver InstallationInstalling Wall Switch Receiver Receiver InformationBulb Replacement OperationFeatures and Ratings Wiring FloodlightFloodlight Lamp ModesTroubleshooting Guide Technical ServiceNo Service Parts Available for this Product Regulatory InformationTWO Year Limited Warranty Calibración de fábrica Calibraciones DEL CódigoEjemplo 1 Calibraciones del código, sistema Ubicaciones DE LOS Interruptores DE Circuito Impreso Interruptores De circuito ImpresoDetector de movimiento de Interruptores de Fase DE LámparaDetectores DE Movimiento DE 180 Y Seleccione modo nocturno o modo de 24 horasInstalación de las baterías Instalación del Detector de MovimientoControles del Detector de Movimiento de Revisión de la operación y de la regulaciónControl DualBrite de reducción de intensidad 180 Área de Cobertura del Detector de Movimiento deMovimientoMovimiento Sensibilidad del Detector de MovimientoInstalación Información DEL ReceptorReceptor DE Pared CON Interruptor Instalación del receptor de pared con interruptor Reemplazo de la bombillaOperación Cableado del reflector ReflectorFases De Lámpara Guía de Análisis de Averías Servicio TécnicoInformación Regulatoria No hay piezas de servicio disponibles para este productoGarantía Limitada a 2 Años Caractéristiques Réglage DES CodesDu guide de référence Exemple 2 Réglage des codes, systèmeEmplacement DES MICRO-INTERRUPTEURS Détecteur de mouvement surInterrupteur récepteur mural ProjecteurInstallation Du Détecteur De Mouvement Sélection du mode de nuit ou du mode 24 heuresInstallation des piles Détecteurs DE Mouvement SUR 180 ETCommande Commandes du détecteur de mouvement surVérification du fonctionnement et du réglage Gradateur DualBriteMDZone de couverture du détecteur de mouvement sur MouvementMouvement DétecteurDétecteurSensibilité du détecteur de mouvement Réglage de la couverture du détecteur de mouvementInterrupteur Récepteur Mural Installation de l’interrupteur transmetteur muralInformations SUR LE Récepteur Remplacement de l’ampoule FonctionnementCâblage du projecteur ProjecteurModes D’Éclairage Service Technique Guide DE DépannageRenseignements de règlements Aucune pièce de rechange n’est disponible pour ce produitGarantie Limitée DE 2 ANS Is nça fra 598-1306-02

598-1306-02 specifications

Heath Zenith 598-1306-02 is a versatile and feature-rich motion-activated outdoor light that enhances home security while providing convenience and energy efficiency. This device is designed to detect motion within a specified range and illuminate outdoor areas, making it an excellent choice for homeowners looking to improve safety around their properties.

One of the hallmark features of the Heath Zenith 598-1306-02 is its advanced motion detection technology. The light is equipped with a passive infrared (PIR) sensor that can detect movement from people or animals in its vicinity. The sensor typically has an adjustable detection range, allowing users to customize how far away motion must occur for the light to activate. This feature is particularly beneficial for ensuring that high-traffic areas such as driveways, porches, and walkways are adequately lit when someone approaches.

In addition to its efficient motion detection capabilities, the Heath Zenith 598-1306-02 offers adjustable brightness settings. This allows users to set the light to a specific brightness level, accommodating various lighting needs. From a subtle glow to brightly illuminating a pathway, users can select the appropriate setting based on their preferences and the surrounding environment.

Another significant characteristic of this outdoor light is its weather-resistant construction. Designed for durability, the Heath Zenith 598-1306-02 can withstand various outdoor conditions, including rain, snow, and extreme temperatures. This ensures that the light remains functional and reliable year-round, enhancing its long-term value.

Moreover, the Heath Zenith 598-1306-02 is built with energy efficiency in mind, utilizing LED technology. LED lights consume significantly less energy compared to traditional incandescent bulbs, resulting in lower electricity bills and a smaller carbon footprint. This eco-friendly approach not only helps save money but also supports sustainability.

Installation is straightforward, thanks to the user's manual guiding users through the process. Whether mounted on walls, ceilings, or eaves, the compact design of the Heath Zenith 598-1306-02 allows it to blend seamlessly with a variety of architectural styles.

Overall, the Heath Zenith 598-1306-02 is an excellent choice for homeowners seeking a reliable and energy-efficient outdoor lighting solution. With its motion detection technology, adjustable brightness settings, durable construction, and energy-saving features, this light delivers on all fronts, making it a smart addition to enhance home safety.
Top Page Image Contents