Carrier 48/50HJ004-014 specifications Type Outlet FLA, FLA LRA Hacr BKR

Table 1E — Electrical Data (COBRA™ Energy Recovery 48HJ008-014 Units with 62AQ200)

	NOMINAL	IFM	CONV	62AQ	POWER SUPPLY		DISCONNECT SIZE*
UNIT						FUSE OR
	V-PH-HZ	TYPE	OUTLET	FLA	MCA		FLA	LRA
						HACR BKR
		STD	NO	21.9	60.1	70	66	366
	208/230-3-60	STD	YES	21.9	66.1	70	71	371
		HIGH STATIC	NO	21.9	63.2	70	69	391
48HJ008		HIGH STATIC	YES	21.9	69.2	80	75	395
		STD	NO	10.2	29.4	35	32	184
	460-3-60	STD	YES	10.2	32.1	35	34	186
		HIGH STATIC	NO	10.2	30.8	35	34	197
		HIGH STATIC	YES	10.2	33.5	35	36	199
		STD	NO	21.9	62.1	70	68	400
	208/230-3-60	STD	YES	21.9	68.1	70	73	405
		HIGH STATIC	NO	21.9	65.2	70	71	425
48HJ009		HIGH STATIC	YES	21.9	65.2	70	71	425
		STD	NO	10.2	31.7	35	34	206
	460-3-60	STD	YES	10.2	34.4	40	37	208
		HIGH STATIC	NO	10.2	33.1	35	36	219
		HIGH STATIC	YES	10.2	35.8	40	38	221
		STD	NO	21.9	74.9	80	81	465
	208/230-3-60	STD	YES	21.9	80.9	90	87	469
		HIGH STATIC	NO	21.9	79.3	90	86	488
48HJ012		HIGH STATIC	YES	21.9	85.3	90	92	493
		STD	NO	10.2	35.1	40	38	234
	460-3-60	STD	YES	10.2	37.8	40	40	236
		HIGH STATIC	NO	10.2	37.7	40	41	245
		HIGH STATIC	YES	10.2	40.4	45	43	247
	208/230-3-60	STD	NO	21.9	82.5	90	89	550
		STD	YES	21.9	88.5	100	95	555
48HJ014
	460-3-60	STD	NO	10.2	39.3	45	43	270
		STD	YES	10.2	42.0	45	45	272

LEGEND

FLA — Full Load Amps

HACR — Heating, Air Conditioning and Refrigeration

IFM — Indoor (Evaporator) Fan Motor

LRA — Locked Rotor Amps

MCA — Minimum Circuit Amps

MOCP — Maximum Overcurrent Protection

NEC — National Electrical Code

UL — Underwriters’ Laboratories

*Used to determine minimum disconnect per NEC.

†Single point box CRSINGLE017A00 is part of base unit.

NOTES:

1.In compliance with NEC requirements for multimotor and combi- nation load equipment (refer to NEC Articles 430 and 440), the overcurrent protective device for the unit shall be fuse or HACR breaker. UL, Canada units may be fuse or circuit breaker.

2.Unbalanced 3-Phase Supply Voltage

Never operate a motor where a phase imbalance in supply volt- age is greater than 2%. Use the following formula to determine the percent of voltage imbalance.

= 100 x	max voltage deviation from average voltage
	average voltage

Example: Supply voltage is 460-3-60.

AB = 452 v BC = 464 v AC = 455 v

Average Voltage = 452 + 464 + 455 3

1371

=

3

= 457

Determine maximum deviation from average voltage. (AB) 457 – 452 = 5 v

(BC) 464 – 457 = 7 v (AC) 457 – 455 = 2 v

Maximum deviation is 7 v.

Determine percent of voltage imbalance.

7

% Voltage Imbalance = 100 x 457

= 1.53%

This amount of phase imbalance is satisfactory as it is below the maximum allowable 2%.

IMPORTANT: If the supply voltage phase imbalance is more than 2%, contact your local electric utility company immediately.

21