Pelco IV SE manual Reverse, Clear Window

Page 55

PELCO SPECTRA IV SE HORIZON

LANGUAGE

<SYSTEM INFORMATION> <DISPLAY SETUP>

<DOME SETTINGS>

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EXIT

DOME SETTINGS

<CAMERA>

<MOTION> <POWER UP> <LINE SYNC> <PRESETS> <PATTERNS> <ZONES>

<WINDOW BLANKING> <ALARMS>

<AUX>

<TITLE TEXT> <CLEAR> <PASSWORD> <CLOCK> <EVENT>

BACK

EXIT

WINDOW BLANKING

STYLE

BLANK ALL ABOVE

BLANK ALL BELOW

<SET WINDOWS>

BACK

EXIT

SET WINDOWS

WINDOW NUMBER

<EDIT WINDOW LOCATION> <EDIT WINDOW ZOOM> <EDIT SCHEDULE>

ENABLE WINDOW

REVERSE

CLEAR WINDOW

BACK

EXIT

6.The blanked area can be programmed to turn on or off at a specified zoom point. To set the zoom point:

a.Use the joystick to position the cursor beside EDIT WINDOW ZOOM, and then press Iris Open.

b.Zoom in to the point where you want window blanking to turn on. Press Iris Open to set the zoom point.

NOTES:

•Since the area is already blanked out, it may be difficult to determine when you want window blanking to turn on. Reverse the window before setting the zoom point. When finished reverse the window again to blank out the area.

•Increase the size of the window if any part of the blanked area is revealed during pan, tilt, and zoom operations.

Window Blanking Disabled

Window Blanking Enabled

EDIT SCHEDULE

The Edit Schedule menu is a duplicate of the Edit Event menu in the Event section with the following exceptions. In the Edit Schedule menu, the event type cannot be changed. Also, the Holiday feature cannot be accessed from the Edit Schedule menu.

For instructions on changing the features in the Edit Schedule menu, refer to the Edit Event section on page 69.

REVERSE

A blanked out area can be reversed to make it visible and the areas on both sides of it not visible. The areas above and below the blanking area remain visible. Reversing the window a second time will return it to its original condition.

CLEAR WINDOW

All areas that have been set for window blanking are cleared.

C3434M-A (9/07)

55

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Spectra IV SE Horizon Series Dome Drive Page Contents Shutter Speed Scheduled Events Welcome Switch Settings InstallationSW1 Receiver Address Baud SW2 Switches 1-3 Special System SettingsSW2 Switches 4-5 Serial Port Settings SW2 Switches 6-8 Baud SettingsDome Drive Installation Dome Drive InstallationTable A. Switch Settings for SW1 P-Type Control Spectra Switch Setting Address Table B. Switch Settings for SW1 D-Type ControlTable B. Switch Settings for SW1 D-Type Control 100 106 141 176 211 246 Getting Started Configure DoneHow to Operate Your Dome System Quick Programming Guide Accessing Main Menu PresetPress the Spot Monitor key CM9500VCD5000 Endura WorkstationSpectra IV SE Horizon Menu Tree Dome Settings Camera Language Back Exit Additional System InformationDisplay Setup Label Positions Auto Focus Dome SettingsCamera Type of LightingHigh Zoom LimitZoom Speed LOW Light LimitYES IR CUT FilterDark Numeric Value Advanced Camera SettingsShutter Speed AGC LimitDetermined by the auto iris level setting Auto iris is disabled, and control is always manualAuto Iris Gain Level. Sharpness level settings range fromAuto Sharpness Auto White BalanceBacklight Compensation BLC There are two backlight compensation settingsNormal Video LevelWide Dynamic Range Set the video output to one of the followingEnhanced DefaultElectronic Image Stabilization Image EnhancementProportional PAN Motion SettingsThere are two auto flip modes On default Auto FlipFrame Scan PresetPark Time Auto ScanImage is never frozen Preset Freeze FrameThere are three preset freeze frame settings Scan SpeedStop is reached Limit StopsManual ScanAzimuth Zero Power UP Action Power UPNone Line Sync Settings range from zero to 359 degreesDome synchronizes to the internal clock Following presets are predefined for specific functions PresetsBecomes Pelco Spectra IV SE Horizon Language Edit Detection Areas Enable Motion DetectionFollowing are the settings for motion detection OFF default Medium default Average sensitivityMotion Detection Areas Edit Schedule Activate AUX CommandTriggers a command to AUX AUX TimePatterns Zones To set a window blanking area Window BlankingClear Window ReverseBlank ALL ABOVE/BLANK ALL below Sequence AlarmsReset Delay ResumeMEDIUM/LOW Normally open Latching AUXMomentary Edit Title Text Title TextClear Password Clock Power LineFixed Date Repeat steps b-d for the ending date and time Follow the instructions in for Fixed DATE, adding Week Event Type EventEvent Label Edit Event Label Edit Event LabelDate is in the list of holidays Edit EventHolidays have no effect on the event List Event Clear EventHoliday Holiday occurs on the same date each year Edit HolidayApril List Holidays Clear HolidayUse this page to record scheduled events Scheduled EventsReboot System Reset, Cycle Power, RebootReset Camera Cycle Camera PowerSoftware/Language File Upload Suggested Preventative Maintenance Ntsc SpecificationsInterlace Inch CCD PAL Product Warranty and Return Information ISO9001
Related manuals
Manual 96 pages 46.76 Kb

IV SE specifications

The Pelco IV SE is a leading-edge camera system designed specifically for surveillance applications that demand high-quality imaging, flexibility, and robustness. With its sleek design and advanced features, the Pelco IV SE is an essential tool for security professionals aiming to enhance situational awareness and improve monitoring capabilities.

One of the key features of the Pelco IV SE is its impressive image quality. The camera is equipped with advanced image sensors that provide high resolution and clarity, ensuring that critical details are captured even in challenging lighting conditions. Its enhanced low-light performance enables efficient operation in darkness, making it suitable for both day and night surveillance tasks.

In terms of technology, the Pelco IV SE incorporates advanced video compression algorithms, such as H.264 and H.265. These technologies allow for efficient bandwidth utilization while maintaining video quality, enabling long-term storage of data without sacrificing clarity. The camera also supports Power over Ethernet (PoE), simplifying installation by allowing power and data to be transmitted over a single cable, reducing clutter and setup complexity.

Another standout characteristic is its flexibility. The Pelco IV SE is designed for various mounting options, including wall, ceiling, and pole mounts, making it adaptable for different environments and surveillance needs. The camera features a varifocal lens, allowing users to adjust the field of view to capture images from different distances, thus optimizing surveillance coverage.

Additionally, the Pelco IV SE integrates seamlessly with existing security systems, providing compatibility with various video management software platforms. This interoperability ensures that users can incorporate the camera into their broader security infrastructure without significant disruption.

The device also comes with intelligent video analytics capabilities, such as motion detection and facial recognition, enhancing its functionality. These features allow for proactive monitoring, where alerts can be set up for suspicious activities, ensuring timely responses to potential threats.

With its robust construction, the Pelco IV SE is built to withstand harsh environmental conditions. It adheres to specific IP ratings, indicating its resistance to dust and water, making it an ideal choice for both indoor and outdoor surveillance applications. In summary, the Pelco IV SE is a versatile, high-performance camera that combines advanced imaging capabilities, reliable technology, and extensive adaptability to meet the evolving demands of modern security surveillance.
Top Page Image Contents