Pelco Not ICS110-CW manual Regulatory Notices, Radio And Television Interference

Page 5
Regulatory Notices

Regulatory Notices

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Offi ce, Washington D.C. 20402.

Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission’s rules.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.

C3406M-D (1/07)

5

Image 5
Contents Integrated Camera System Wide Dynamic Range WDR C3406M-D 1/07ICS110-CW Series Camclosure I N S T A L L A T I O NPage Side Conduit Installation ContentsVarifocal Lens Zoom and Focus Adjustments Vertical Phase Adjustment 24 VAC Operation OnlyList of Illustrations RADIO AND TELEVISION INTERFERENCE Regulatory NoticesMODELS DescriptionFigure 1. Package Components SHOWN ACTUAL SIZEUNSHIELDED TWISTED PAIR UTP VIDEO Cover and Back Box InstallationBASIC SURFACE INSTALLATION 4S ELECTRICAL BOX INSTALLATION ADAPTER PLATE 404 PLASTER RING INSTALLATION SIDE CONDUIT INSTALLATION 8-32 X 0.375-INCH PHILLIPS PAN HEAD SCREWS WITH WASHERS SUPPLIED COVER 0.75-INCH CONDUIT CONNECTOR BACK BOX REMOVE CONDUIT PLUGMODULE REMOVAL Camera ModuleHEATER BOARD CONNECTOR SERVICECAMERA CONNECTORCONNECTOR Figure 7. Back Box ConnectorsCAMERA ORIENTATION MODULE INSTALLATIONVARIFOCAL LENS ZOOM AND FOCUS ADJUSTMENTS Camera AdjustmentsSWITCH SETTINGS ADJUSTING THE VERTICAL PHASE VERTICAL PHASE ADJUSTMENT 24 VAC OPERATION ONLYTilt Camera PositioningFigure 12. Positioning the Camera RotationInstall Dome and Trim Ring Service Connector 1 2.5 mm monaural headphone plug 1 CPM 88 miniature coaxial connector LENS SpecificationsCAMERA Electrical BACKBOXGeneral Design and product specifications subject to change without noticeC3406M-D 1/07 WARRANTY PRODUCT WARRANTY AND RETURN INFORMATIONREVISION HISTORY RETURNSUSA & Canada Tel 800/289-9100 Fax 800/289-9150 International Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USATel 1-559/292-1981 Fax 1-559/348-1120 ISO9001