SkyLink 91561-01, 91558-01A, 91562-01 service manual Yellow Andwhite Lead Connections to Headlamp

is06731

1

1. Headlamp connector [38]

Figure 23. Wire Splice Locations (2005 and Later V-Rod)

YELLOW ANDWHITE LEAD CONNECTIONS TO HEADLAMP

Dyna Models

1.See Figure 24. Use cable straps from the kit to fasten the remaining transmitter wires (yellow and white) and conduit to the motorcycle wires leading to the headlamp. Lift the fuel tank as needed to feed the wires under the tank and toward the headlamp.

is06726

Figure 24. Transmitter Wire Routing to Headlamp (Dyna)

2.Route the wires into the headlamp housing through the grommet on the lower rear of the housing.

NOTE

To route the transmitter wires through the grommet, push a hooked piece of wire through the grommet from the inside of the headlamp housing.

A light coat of liquid soap, window cleaner or all-purpose lub- ricant may be needed to pull the wires back through the grommet with the hooked wire.

In some applications the transmitter wires may not fit through the headlight housing grommet. In that case, the wires must be spliced outside the headlamp housing.

3.Cut the yellow and white wires in the headlamp housing several inches from the headlamp connector. Cut excess length from the yellow and white transmitter wires if necessary. Cut to allow enough wire to easily strip and splice the wires.

4.See Figure 15, the 1 into 1 splice configuration. Use a blue sealed splice connector (Figure 27, Item 5) from the

kit to splice the white transmitter wire to the white head- lamp wires. Use the remaining blue sealed splice con- nector to splice the yellow transmitter wire to the yellow headlamp wires.

5.Proceed to the Receiver and Transmitter Programming section to program the garage door opener controls.

Softail Models

1.Use cable straps from the kit to fasten the remaining transmitter wires (yellow and white) and conduit to the motorcycle wires leading to the headlamp. Lift the fuel tank as needed to feed the wires under the tank and toward the headlamp.

NOTE

For 2011 and later Softail models, the headlamp circuit wires in the vehicle harness are blue with a white or yellow tracer, rather than solid white and solid yellow as described in the following steps.

2.Cut the yellow and white wires in the main vehicle harness headlamp circuit at an accessible point. Cut excess length from the yellow and white transmitter wires if necessary. Trim back the transmitter wire harness casing as needed to assist splicing. Cut to allow enough wire to easily strip and splice the wires.

3.Slide the woven wire conduit (9) from the kit over the yellow and white transmitter wires.

4.See Figure 15, the 1 into 1 splice configuration. Use a blue sealed splice connector (Figure 27, Item 5) from the kit to splice the white transmitter wire to the white head- lamp wires. Use the remaining blue sealed splice con- nector to splice the yellow transmitter wire to the yellow headlamp wires.

5.Slide the woven wire conduit over the yellow and white wire connections after splicing.

6.Proceed to the Receiver and Transmitter Programming section to program the garage door opener controls.

Sportster Models

1.Route the remaining transmitter wires (yellow and white) and conduit through the top of the frame under the fuel tank and up to the headlamp. Use cable straps from the kit to fasten the wires to the harness.

2.Route the wires into the headlamp housing through the grommet on the lower rear of the housing.

NOTE

To route the transmitter wires through the grommet, push a hooked piece of wire through the grommet from the inside of the headlamp housing.

A light coat of liquid soap, window cleaner or all-purpose lub- ricant may be needed to pull the wires back through the grommet with the hooked wire.

In some applications the transmitter wires may not fit through the headlight housing grommet. In that case, the wires must be spliced outside the headlamp housing. See Figure 25.

-J02028 12 of 16