SkyLink 91558-01A Harness Connection, General, Later Softail Models, Touring and Trike Models

Page 7

HARNESS CONNECTION

General

Splicing of wire leads is necessary in the installation of the garage door opener to the vehicle. Find the instructions for a specific model in the sections that follow, and refer to the ser- vice manual appendix for proper wire splicing procedures.

Be sure to follow manufacturer's instructions when using the UltraTorch UT-100 or any other radiant heating device. Failure to follow manufacturer's instructions can cause a fire, which could result in death or serious injury. (00335a)

•Avoid directing heat toward any fuel system component. Extreme heat can cause fuel ignition/explosion resulting in death or serious injury.

•Avoid directing heat toward any electrical system com- ponent other than the connectors on which heat shrink work is being performed.

•Always keep hands away from tool tip area and heat shrink attachment.

For 2011 and later Softail models: Proceed to the following

section.

For Touring and Trike models: Proceed to that section.

For ALL OTHER models: Proceed to Black Lead Connection for the specific model.

2011 and Later Softail Models

NOTES

Requires separate purchase of Electrical Connection Harness (H-D Part No. 72673-11).

Electrical connectors are identified in the service manual by the number and letter shown here within brackets.

1.Locate the Digital Technician connector [91A] (a gray six- way Deutsch pin connector with a rubber boot) under the seat. Place the Electrical Connection Harness at connector [91A], but DO NOT connect at this time.

2.Route the garage door opener wires over to the Electrical Connection Harness. Remove the orange/white wire from the conduit. Cut the orange/white and black wires to a suitable length to easily reach the sealed splice connectors on the Electrical Connection Harness. DO NOT cut the yellow or white wires.

3.Splice the black garage door opener wire to the black wires in the Electrical Connection Harness.

4.Splice the orange/white garage door opener wire to the red/yellow wires in the Electrical Connection Harness.

5.Use a heat gun or suitable radiant-heating device to shrink the connector to the wires.

6.Use the heat gun or heating device to seal the open end of the sealed splice connector on the red/blue wires in the Electrical Connection Harness.

7.Pull the rubber boot out from the gray Digital Technician pin connector [91A]. Cut the boot off of the wires.

8.Connect the socket housing of the Electrical Connection Harness to connector [91A].

9.Insert the rubber boot into the open pin connector of the Electrical Connection Harness.

10.Loosen or remove the four screws holding the ECM to the mounting bracket. Route the Electrical Connection Harness under the ECM connector. Tighten the four screws to 45-55 in-lbs(5.1-6.2 Nm).

11.Proceed to the Yellow and White Lead Connections section for the specific model.

Touring and Trike Models

1.Cut the yellow, white and orange/white transmitter wires to about the same length as the transmitter black ground wire. Cut to allow enough wire to easily strip and splice the wires.

is06725

1

3

 

2

 

4

1.Black (ground) wire

2.Yellow wire

3.White wire

4.Orange/white wire

Figure 14. Wires for Transmitter Connections (FLHR)

2.FLHR Touring Models: See Figure 14. Cut the yellow (2), black (1) and white (3) headlamp wires inside the nacelle, staggering the lengths a bit to avoid all three splices being together.

FLHT and FLHX Touring and Trike Models: See Figure 9. Cut the yellow (6), black (4) and white (5) headlamp wires inside the fairing, staggering the lengths a bit to avoid all three splices being together.

FLTR Touring Models: See Figure 10. Cut the yellow (6), black (4) and white (5) headlamp wires inside the fairing, staggering the lengths a bit to avoid all three splices being together.

ALL Touring/Trike Models: Slide the woven wire conduit from the kit (see Figure 27, Item 9) over all three headlamp wires.

3.See Figure 15, the 2 into 1 splice configuration. Use a red sealed splice connector (Figure 27, Item 4) from the kit to splice the black garage door opener transmitter wire to the black wires from the headlamp. Trim back the trans- mitter wire harness casing as needed to assist splicing.

-J02028

7 of 16

Page 6 Page 8
Image 7
Page 6 Page 8
Contents FCC Notices GeneralVehicle Preparation Receiver InstallationEarlier Softails Transmitter InstallationFor Dyna, Softail and Sportster models Dyna ModelsRear wheel and tire Rear fork Transmitter Later Softails, Except Deuce FxstdLater Softail Deuce Fxstd Sportster ModelsFlhr Touring Models Later Sportster ModelsFLHT, Flhx and Fltr Touring ModelsTrike Models Louvered cover Tab Screw Transmitter Fuse block wire harnessRod Models Later V-Rod ModelsTouring and Trike Models Harness ConnectionGeneral Later Softail ModelsEarlier Softail Models Black Lead Connection to GroundInto 1 splice Later Dyna Models ORANGE/WHITE Lead Connection to Switched Power SourceGround screws black wire Earlier Dyna ModelsSoftail Models Fuse Block Adapter Wire Dyna and SoftailWire Splice Locations 2002-2003 V-Rod Power Connections Sportster ModelsYellow Andwhite Lead Connections to Headlamp Wire Splice Locations 2005 and Later V-RodIs06727 Receiver and Transmitter Programming TroubleshootingReset the Receiver NO. Proceed to Reset the ReceiverService Parts Not sold separately

91562-01, 91558-01A, 91561-01 specifications

SkyLink has made a remarkable entry into the realm of wireless communication devices with its innovative models: the SkyLink 91562-01, 91558-01A, and 91561-01. Each of these devices is tailored to meet the demands of modern security systems, providing reliability and efficiency for both residential and commercial applications.

The SkyLink 91562-01 stands out for its versatility and ease of use. This wireless communication hub can connect with multiple sensors and devices, enabling a comprehensive security system. Featuring advanced encryption technology, it ensures that communications between the hub and connected devices remain secure from unauthorized access. The 91562-01 supports DIY installation, which means users can easily set up their system without needing professional assistance. Additionally, its sleek design allows it to blend seamlessly into any home decor.

Next, the SkyLink 91558-01A is engineered to provide enhanced connectivity and communication. It features long-range capabilities, allowing it to cover expansive areas without losing signal strength. This model is compatible with a variety of SkyLink sensors and accessories, enabling users to customize their security system according to their specific needs. The 91558-01A is equipped with a built-in backup battery, ensuring that the system remains operational even during power outages, a crucial feature for maintaining security integrity.

Finally, the SkyLink 91561-01 is particularly suited for users who prioritize ease of access and monitoring. With its user-friendly interface, it allows users to manage their security settings and receive real-time alerts from anywhere using a mobile app. This model supports remote access, adding a layer of convenience for those on the go. Moreover, the 91561-01 integrates with smart home devices, providing a holistic approach to home automation and security.

In summary, the SkyLink 91562-01, 91558-01A, and 91561-01 represent a convergence of technology, security, and user-friendliness. With features like long-range communication, innovative encryption, and mobile connectivity, these devices are designed to cater to the dynamic needs of users, ensuring safety and peace of mind in an increasingly connected world. Each model brings its set of strengths to the table, making them suitable for a wide range of applications and user preferences. SkyLink continues to push the envelope in wireless communication and security technology, solidifying its position as a leader in the industry.
Top Page Image Contents