SkyLink SC-100 Standard Arming Sequences, Additional Arming Sequences, To Customize a Sequence

ADVANCED PROGRAMMING

STANDARD ARMING SEQUENCES

Each zone can be programmed to react 5 different ways when it receives a signal from a remote sensor.

1. Chime Mode - represented by the green lights

When only the green light is on and the Control Panel receives a signal from a remote sensor, the Control Panel emits a subtly two tone chime.

2. Instant Mode - represented by the red lights

When only the red light is on and the Control Panel receives a signal from the remote sensor, the Control Panel will activate the siren instantly.

3. Delay Entry Mode - represented by the green and red lights

When both the green and red lights are on and the Control Panel receives a signal from a remote sensor, the lights will flash and the Control Panel will beep for 30 seconds before the alarm sounds. These 30 seconds give you time to enter the premises and deactivate the alarm before the siren sounds.

4.Delay Exit Mode - represented by the flashing of both the green and red lights for 45 seconds

When both green and red lights are flashing, the control panel will not recognize any remote sensors communicating to that zone. These 45 seconds allow you time to exit the premises before that zone is activated. When the lights stop flashing, both green and red lights will remain on, which is now in DELAY ENTRY MODE.

(See above for information on DELAY ENTRY MODE).

5. Off - neither the green nor the red lights are on.

The Control Panel will not recognize any signals from a remote sensor.

We have preprogrammed different combinations of the above modes to meet different situations, (see STANDARD PROGRAMMING).

ADDITIONAL ARMING SEQUENCES

Below are three additional programming options you may want to use.

Option 1: Advanced Home 1 - use to secure the premises while staying in the building. Delays the alarm to allow someone to enter the building and deactivate the alarm.

1.Enter the current MPIN.

2.Press [ A ].

3.Press [ A ].

You will hear a long beep. The arm light, the red and green lights in zones 1 and the red lights in zones 3 and 4 go on. Zone 1 has the entry delay to allow some- one to enter through the front door and deactivate the system before the siren sounds. This option does not have the exit delay so you are not able to leave the

ADVANCED PROGRAMMING

premises without activating the alarm. Zone 2 (the motion sensor), is off allowing movement in the premises and zones 3 & 4 are instant.

Option 2: Advanced Home 2 - use to secure the premises while staying in the building. Delays the alarm to allow someone to enter the building and/or walk in the monitored area of the motion sensor to deactivate the alarm.

1.Enter the current MPIN.

2.Press [ A ].

3.Press [ C ].

You will hear a long beep. The arm light, the red and green lights in zones 1 and 2 as well as the red lights in zones 3 and 4 go on. Zone 1 & 2 has the entry delay to allow someone to enter through the front door and walk in the area monitored by the motion sensor and deactivate the system before the siren sounds. This option does not have the exit delay so you are not able to leave the premises without activating the system. Zones 3 & 4 are instant.

Option 3: Chime Sequence - this sequence is used for testing the system but it can also be used to subtly alert you when a zone has been activated. Example, if a young child opens the front door, the Control Panel will emit a two tone chime advising you that the front door has been opened. (See page 10 for programming information for the CHIME SEQUENCE.)

The three arm sequences above ; Advanced Home 1, Advanced Home 2 and Chime Sequence along with the three sequences described in the STANDARD PROGRAMMING; Away Sequence, Home Sequence and Night Sequence, make up the six preprogrammed arm sequences.

However, if any of these six sequences do not satisfy your needs, you may want to change the modes in certain zones. For example, your zone 2, (motion sensor) is currently in delay mode. If your motion sensor is located in the basement and you would like to change it to the instant mode, see below.

TO CUSTOMIZE A SEQUENCE:

Program the system to the sequence you want to alter.

1.Enter the current MPIN.

2.Press [ B ].

3.Press a number key to select the zone you would like to change, [ 1, 2, 3 or 4 ]. The zone lights in the chosen zone will flash for eight seconds.

4.While the lights flash, press [ A ].

5.Select the new mode you want to use:

[ 0 ] = Disarm, [ 1 ] = Chime Mode, [ 2 ] = Delay Entry/Exit Mode, [ 3 ] = Instant Mode

6. Press [ * ].

A long beep signals a successful change.

–21– –22–