SkyLink SC-100 Motion Sensor Battery, DOOR/WINDOW Sensor Battery, Keychain Transmitter Battery

Page 15

BATTERY MAINTENANCE

MOTION SENSOR BATTERY

The Motion Sensor operates on a 9 volt alkaline battery accessible beneath a sliding panel on the bottom of the unit. All remote sensors come with the battery. Disarm the Control Panel before replacing all batteries.

When low battery level is detected, the motion sensor will beep to alert you the battery needs to be replaced. When the low battery signal appears, it will not trans- mit any signal to the receiver even motion is detected. Therefore, you should replace the battery as soon as the low battery signal appears.

Note: Alkaline battery must be used.

To replace the Motion Sensor battery:

1.Slide to remove the sensor from the ball-head joint.

2.Undo the screw and remove the battery cover.

3.Take the old battery out of the battery compartment.

4.Disconnect the old battery from the connector wire.

5.Connect the new alkaline battery to the connector wire.

6.Put the new battery into the battery compartment.

7.Close the battery cover and re-insert the screw.

8.Slide the unit back to the ball-head joint.

BATTERY MAINTENANCE

DOOR/WINDOW SENSOR BATTERY

Each door/window sensor operates on a 12 volt alkaline battery that is inside the transmitter. The sensors come with the batteries already installed.

To replace the battery:

1.

Push on the clip at the bottom of the transmitter

 

 

case with a sharp object (such as a paper clip

 

 

or pen knife) and pull it away from the backplate.

-

2.

Pry out the old battery from one end.

3.

Push the new battery back into place. A diagram

+

 

beside the battery well indicates which end is

 

 

positive and which is negative.

 

4.Snap the transmitter back onto the backplate.

KEYCHAIN TRANSMITTER BATTERY

The Keychain Transmitter operates on a 12 volt alkaline battery which is installed at the factory.

There are two screws on the back of the transmitter that holds the case together.

To replace the Keychain Transmitter battery:

1.Undo the two screws on the back of the transmitter.

The back will then come off.

2.Using a small screwdriver or pen knife, pry out the old battery from one end.

3.Place the new battery in position.

A diagram beside the battery well

+

indicates which end is positive and

which is negative.

-

 

4.Close the battery cover and re-insert the two screws.

–25–

–26–

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Customer Service Fax / Télécopieur 800Email / Courrier électronique support@skylinkhome.com Total Protection Alarm System Table of Contents Total Protection Alarm SystemOverview Package ContentsPlanning Your Home Security Needs InstallationHow to use the templates Installing the Control Panel SC-001Sensor Sensitivity Installing the DOOR/WINDOW Sensor WT-433Installing the Motion Sensor PS-434A Transmitter Magnetic SwitchTo test the Door/Window Sensor Testing Your SystemTo set control panel to Chime Mode Walk TestStandard Programming Lights and SoundsTo Disarm the System Using the Keypad on the Control Panel To ARM System Using the Keychain TransmitterKeychain Transmitter 4B-434 Passwords Panic Button on the Keychain TransmitterMaster Personal Identification Number Mpin Deleting a Spin Advanced ProgrammingSecondary Personal Identification Number Spin Adding a SpinEnter the current Mpin Press B To Clear a ZoneTo Program a Sensor to a Zone To Delete a Keychain Transmitter from ZoneStandard Arming Sequences Additional Arming SequencesTo Customize a Sequence Summary of Arming Sequences Battery MaintenanceControl Panel Battery To replace the Control Panel backup batteryMotion Sensor Battery DOOR/WINDOW Sensor BatteryKeychain Transmitter Battery Additional Accessories Keychain Transmitter 4B-433A Alarm Sensor SS-433Temperature Sensor TS-433 Audio Sensor AS-433Système de Sécurité Sans fil Table DES Matières VUE Densemble Contenu DE LemballageComment utiliser les gabarits Installation DU Panneau DE Commande SC-001Pour monter le panneau de commande Planification SUR VOS Besoins DE Sécurité a DomicileInstallation DU Détecteur DE Mouvements PS-434A Installation DE Capteurs PORTE/FENÊTRE WT-433Sensibilité DU Détecteur Pour tester les capteurs de porte/fenêtre Pour régler le panneau de commande au Mode CarillonTester Votre Système Test DE MarcheSons Lumières ET SonsLumières Lumières DE ZoneSéquences d’armement Programmation DE BaseLE Bouton Panique SUR LE Transmetteur PORTE-CLEFS Transmetteur PORTE-CLEFS À Distance 4B-434Lorsque le système est armé Lorsque la sirène se fait entendreMots DE Passe Numéro D’IDENTIFICATION Personnel Principal NippNuméro D’IDENTIFICATION Personnel Secondaire Nips Programmer UN Capteur À UNE Zone Programmation AvancéeProgrammer DES Capteurs À Différentes Zones Libérer UNE ZonePour Libérer LE Transmetteur PORTE-CLEFS DE LA Zone Séquences D’ARMEMENT DE BaseSéquences Darmement Additionnelles Personnaliser UNE Séquence Entretien DE LA Pile Pile DU Panneau DE CommandePour remplacer la pile de secours du panneau de commande Sommaire DES Séquences D’ARMEMENTPile DU Détecteur DE Mouvements Pile DU Capteur DE PORTE/FENÊTREPile DU Transmetteur PORTE-CLEFS Accessoires Additionnels Transmetteur Porte-clefs 4B-433A Détecteur de temperature TS-433Détecteur de fumée SS-433 Detecteur son AS-433Sistema de Alarma con Protección Total Índice Descripción Contenido DEL ConjuntoPara Instalar EL Panel DE Control SC-001 Cómo Planear LA Seguridad DE SU Hogar / NegocioInstalación Como utilizar los modelosTransmisor Interruptor magnetico Imán Instalando EL Sensor DE Movimiento PS-434AInstalando EL Sensor PUERTA/FENESTRA WT-433 Sensibilidad DEL SensorPara probar el sensor puerta / fenestra Prueba DE SU SistemaPrueba Walk Test Para fijar el Panel de Control al modo del CarillonEntry MODE. Acción Retardada Luces Y SonidosPresione el Mpin actuál 0 0 Presione a Presione B Programacion EstandardSecuencias para alejarse Por ejemplo durante la noche cuando todos estan durmiendoHay dos diversas opciones para armar que usted puede elegir Transmisór a Llavero 4B-434Armar EL Sistema Usando EL Transmisór Llavero Incorpore el Mpin actuál 0 0 Presione B BPalabras DE Paso EL Botón DE Pánico EN EL Transmisór LlaveroNúmero Principal DE Identificación Personal Mpin Suprimiendo una Spin Programación AvanzadaNúmero Secundariode Identificacion Personal Spin Adición de una SpinPara Cancelar UN Transmisor Llavero DE LA Zona Para Borrar UNA ZonaPara Programar UN Sensor a UNA Zona Secuencias Adicionales DEL Armar Sequencias Estandárd Para ArmarSumario DE LAS Secuencias Para Armar Paramodificar UNA Secuenciapararequisitos ParticularesAbajo es un sumario de todas las secuencias preprogramadas Batería DEL Sensor DE Movimiento Mantenimiento DE LAS BateriasAcumulador DEL Panel DE Control Para Remplazarlabateríadereservadelpanel DE ControlBateria DEL Transmisor Llavero Accesorios AdicionalesBatería DEL Sensor DE LA Puerta / Fenestra Para substituir la bateríaTransmisor con el Botón de Panico, Agua Resistiente PT-434 El Audio Alarmar AA-433Alarma Silencioso SW-433 Sensor de Vibración VS-433

SC-100 specifications

The SkyLink SC-100 is an advanced drone designed for a variety of aerial applications, catering to both professionals and enthusiasts. This versatile drone integrates cutting-edge technology, making it stand out in a competitive market.

One of the key features of the SkyLink SC-100 is its high-resolution camera, capable of capturing stunning 4K videos and high-quality images. The camera is equipped with a gimbal stabilization system that eliminates vibrations, ensuring smooth footage even in challenging conditions. This is particularly beneficial for photography, videography, and surveillance tasks, allowing users to capture detailed imagery from a bird's-eye view.

The drone boasts an impressive flight time of up to 30 minutes on a single charge, thanks to its efficient battery design. This extended duration allows users to conduct longer missions without the need for frequent recharges. The SC-100 also features an intelligent battery management system that monitors the battery's health and performance, providing users with data to ensure optimal operation.

Speed and agility are hallmarks of the SkyLink SC-100, which can reach speeds of up to 50 km/h. Its powerful motors and aerodynamic design enable it to perform complex maneuvers with ease, making it suitable for dynamic applications such as racing or search and rescue missions. Additionally, the drone is equipped with a range of smart flight modes, including follow-me, waypoint navigation, and orbit mode, enhancing its adaptability for various scenarios.

Another noteworthy feature is its robust obstacle avoidance system. The SC-100 incorporates multiple sensors, including ultrasonic and visual sensors, allowing it to perceive its surroundings and navigate safely without collisions. This technology is particularly useful for beginners and professionals alike, providing an added layer of safety during flight.

Furthermore, the SkyLink SC-100 supports a user-friendly mobile app that enables real-time control and monitoring. The app provides access to advanced features such as live streaming of footage, customizable flight paths, and detailed telemetry data. Users can easily share their captured content through integrated social media options, enhancing engagement with their audience.

In summary, the SkyLink SC-100 stands out with its high-quality camera, impressive flight time, speed, obstacle avoidance technology, and user-friendly controls. These features make it an exceptional choice for drone enthusiasts and industry professionals looking to leverage aerial technology for various applications. Whether for recreational use, aerial photography, or commercial projects, the SC-100 promises reliability and performance.
Top Page Image Contents