SkyLink SC-100 manual Testing Your System, Walk Test, To set control panel to Chime Mode

Page 7

INSTALLATION

WALK TEST

After mounting the sensor at the desired location, it is important to perform a walk test in order to determine if the sensor is detecting the things you want to detect.

In order to control how far the sensor can “see”, this can be done by adjusting the angle of the sensor. To reduce the detection range, simply move the sensor downward. To increase the range, move the sensor up to around 12

degrees. This will give the maximum range. However, this may not be desired ifthe sensorisplacedoutdoors,sincea false trigger may occur if the sensor is

set to detect motion in a distance.

You should walk in the area that you would like the sensor to monitor. Entry the CHIME mode by pressing 000A# on the SC-001. The receiver will beep if the sensor detects your movement. If the sensor does not respond, adjust the mounting angle accordingly. Perform the walk test again after 30 seconds. Repeat this procedure until your motion is detected. There should be no movement in the detected area during the 30 seconds.

Perform walk test in the undesired area to ensure movement cannot be detected.

Tips: The sensor should not face towards direct sunlight, placing near heat or cold producing devices (i.e. A/C or furnance vents, fans, ovens, heaters etc.) that may cause false triggers.

12º

Move the sensor downward to

Move the sensor up to around

reduce the range.

12 º to give maximum range.

TESTING YOUR SYSTEM

Before you learn how to use your security system, test to make sure that the door/ window sensors and the motion sensor are communicating with the Control Panel.

Set the Control Panel to CHIME MODE which will emit a subtly two tone chime when any of the sensors are activated.

To set control panel to CHIME MODE

1.Enter your MPIN [0, 0, 0] on the Control Panel (MPIN is factory set at [0, 0, 0]. To change MPIN see MASTER PERSONAL IDENTIFICATION NUMBER (MPIN) on page 16.

2. Press [ A ].

1

2

3

4

CHIME

DELAY

AC PWR LO BATT. ARM

 

 

 

 

INSTANT

3. Press [ # ].

The red arm light and all 4 green lights above the numbers and beside the word chime will go on. The system will now emit a chime sound when any sensor is activated. The lights and sounds of the Control Panel are explained in the next section (see Lights and Sounds).

The door/window sensors are factory set to communicate with zone 1 and the motion sensor to communicate with zone 2. If you would like to have the sensors communicate with a different zone, see PROGRAM SENSORS TO DIFFERENT ZONES on page 18.

To test the Door/Window Sensor

Open the door/window and break the contact between the magnetic switch and the magnet. A signal will then be sent to the Control Panel which will chime telling you that the signal has been received. One of the four green lights on the Control Panel will flash once as the chime sounds. If you open the front door, the green light above the #1 (zone 1) will flash.

To test the Motion Sensor

Power up the motion sensor. Walk in the monitored area in front of the motion sensor. Once movement is detected, a signal will be sent to the Control Panel. The Control Panel will then emit a two tone chime and the green light above the #2 (zone 2) will flash once. The motion sensor has been programmed to send its signal to zone 2 in the Control Panel. It will take about 20 seconds for the motion sensor to reset itself before it can send another signal.

If you have pets, have them walk in the monitored area to see if they activate the motion sensor. If so, turn the motion sensor off if these pets have access to the monitored area.

–9–

–10–

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Fax / Télécopieur 800 Customer ServiceEmail / Courrier électronique support@skylinkhome.com Total Protection Alarm System Table of Contents Total Protection Alarm SystemOverview Package ContentsPlanning Your Home Security Needs InstallationHow to use the templates Installing the Control Panel SC-001Sensor Sensitivity Installing the DOOR/WINDOW Sensor WT-433Installing the Motion Sensor PS-434A Transmitter Magnetic SwitchTo test the Door/Window Sensor Testing Your SystemTo set control panel to Chime Mode Walk TestStandard Programming Lights and SoundsTo ARM System Using the Keychain Transmitter To Disarm the System Using the Keypad on the Control PanelKeychain Transmitter 4B-434 Panic Button on the Keychain Transmitter PasswordsMaster Personal Identification Number Mpin Deleting a Spin Advanced ProgrammingSecondary Personal Identification Number Spin Adding a SpinEnter the current Mpin Press B To Clear a ZoneTo Program a Sensor to a Zone To Delete a Keychain Transmitter from ZoneAdditional Arming Sequences Standard Arming SequencesTo Customize a Sequence Summary of Arming Sequences Battery MaintenanceControl Panel Battery To replace the Control Panel backup batteryDOOR/WINDOW Sensor Battery Motion Sensor BatteryKeychain Transmitter Battery Additional Accessories Keychain Transmitter 4B-433A Alarm Sensor SS-433Temperature Sensor TS-433 Audio Sensor AS-433Système de Sécurité Sans fil Table DES Matières VUE Densemble Contenu DE LemballageComment utiliser les gabarits Installation DU Panneau DE Commande SC-001Pour monter le panneau de commande Planification SUR VOS Besoins DE Sécurité a DomicileInstallation DE Capteurs PORTE/FENÊTRE WT-433 Installation DU Détecteur DE Mouvements PS-434ASensibilité DU Détecteur Pour tester les capteurs de porte/fenêtre Pour régler le panneau de commande au Mode CarillonTester Votre Système Test DE MarcheSons Lumières ET SonsLumières Lumières DE ZoneSéquences d’armement Programmation DE BaseLE Bouton Panique SUR LE Transmetteur PORTE-CLEFS Transmetteur PORTE-CLEFS À Distance 4B-434Lorsque le système est armé Lorsque la sirène se fait entendreNuméro D’IDENTIFICATION Personnel Principal Nipp Mots DE PasseNuméro D’IDENTIFICATION Personnel Secondaire Nips Programmer UN Capteur À UNE Zone Programmation AvancéeProgrammer DES Capteurs À Différentes Zones Libérer UNE ZoneSéquences D’ARMEMENT DE Base Pour Libérer LE Transmetteur PORTE-CLEFS DE LA ZoneSéquences Darmement Additionnelles Personnaliser UNE Séquence Entretien DE LA Pile Pile DU Panneau DE CommandePour remplacer la pile de secours du panneau de commande Sommaire DES Séquences D’ARMEMENTPile DU Capteur DE PORTE/FENÊTRE Pile DU Détecteur DE MouvementsPile DU Transmetteur PORTE-CLEFS Accessoires Additionnels Transmetteur Porte-clefs 4B-433A Détecteur de temperature TS-433Détecteur de fumée SS-433 Detecteur son AS-433Sistema de Alarma con Protección Total Índice Descripción Contenido DEL ConjuntoPara Instalar EL Panel DE Control SC-001 Cómo Planear LA Seguridad DE SU Hogar / NegocioInstalación Como utilizar los modelosTransmisor Interruptor magnetico Imán Instalando EL Sensor DE Movimiento PS-434AInstalando EL Sensor PUERTA/FENESTRA WT-433 Sensibilidad DEL SensorPara probar el sensor puerta / fenestra Prueba DE SU SistemaPrueba Walk Test Para fijar el Panel de Control al modo del CarillonEntry MODE. Acción Retardada Luces Y SonidosPresione el Mpin actuál 0 0 Presione a Presione B Programacion EstandardSecuencias para alejarse Por ejemplo durante la noche cuando todos estan durmiendoHay dos diversas opciones para armar que usted puede elegir Transmisór a Llavero 4B-434Armar EL Sistema Usando EL Transmisór Llavero Incorpore el Mpin actuál 0 0 Presione B BEL Botón DE Pánico EN EL Transmisór Llavero Palabras DE PasoNúmero Principal DE Identificación Personal Mpin Suprimiendo una Spin Programación AvanzadaNúmero Secundariode Identificacion Personal Spin Adición de una SpinPara Borrar UNA Zona Para Cancelar UN Transmisor Llavero DE LA ZonaPara Programar UN Sensor a UNA Zona Secuencias Adicionales DEL Armar Sequencias Estandárd Para ArmarParamodificar UNA Secuenciapararequisitos Particulares Sumario DE LAS Secuencias Para ArmarAbajo es un sumario de todas las secuencias preprogramadas Batería DEL Sensor DE Movimiento Mantenimiento DE LAS BateriasAcumulador DEL Panel DE Control Para Remplazarlabateríadereservadelpanel DE ControlBateria DEL Transmisor Llavero Accesorios AdicionalesBatería DEL Sensor DE LA Puerta / Fenestra Para substituir la bateríaTransmisor con el Botón de Panico, Agua Resistiente PT-434 El Audio Alarmar AA-433Alarma Silencioso SW-433 Sensor de Vibración VS-433

SC-100 specifications

The SkyLink SC-100 is an advanced drone designed for a variety of aerial applications, catering to both professionals and enthusiasts. This versatile drone integrates cutting-edge technology, making it stand out in a competitive market.

One of the key features of the SkyLink SC-100 is its high-resolution camera, capable of capturing stunning 4K videos and high-quality images. The camera is equipped with a gimbal stabilization system that eliminates vibrations, ensuring smooth footage even in challenging conditions. This is particularly beneficial for photography, videography, and surveillance tasks, allowing users to capture detailed imagery from a bird's-eye view.

The drone boasts an impressive flight time of up to 30 minutes on a single charge, thanks to its efficient battery design. This extended duration allows users to conduct longer missions without the need for frequent recharges. The SC-100 also features an intelligent battery management system that monitors the battery's health and performance, providing users with data to ensure optimal operation.

Speed and agility are hallmarks of the SkyLink SC-100, which can reach speeds of up to 50 km/h. Its powerful motors and aerodynamic design enable it to perform complex maneuvers with ease, making it suitable for dynamic applications such as racing or search and rescue missions. Additionally, the drone is equipped with a range of smart flight modes, including follow-me, waypoint navigation, and orbit mode, enhancing its adaptability for various scenarios.

Another noteworthy feature is its robust obstacle avoidance system. The SC-100 incorporates multiple sensors, including ultrasonic and visual sensors, allowing it to perceive its surroundings and navigate safely without collisions. This technology is particularly useful for beginners and professionals alike, providing an added layer of safety during flight.

Furthermore, the SkyLink SC-100 supports a user-friendly mobile app that enables real-time control and monitoring. The app provides access to advanced features such as live streaming of footage, customizable flight paths, and detailed telemetry data. Users can easily share their captured content through integrated social media options, enhancing engagement with their audience.

In summary, the SkyLink SC-100 stands out with its high-quality camera, impressive flight time, speed, obstacle avoidance technology, and user-friendly controls. These features make it an exceptional choice for drone enthusiasts and industry professionals looking to leverage aerial technology for various applications. Whether for recreational use, aerial photography, or commercial projects, the SC-100 promises reliability and performance.
Top Page Image Contents