Appendix C Ping IP Address | Rosewill RXS-4324, RXS-3323 manual

Page 65

Internet Camera RXS-3323/RXS-4324		User Manual

Appendix C: Ping IP Address

The PING (stands for Packet Internet Groper) command is used to detect whether a specific IP address is accessible by sending a packet to the specific address and waiting for a reply. It’s also a very useful tool to confirm the device installed or if the IP address conflicts with any other devices over the network.

If you want to make sure the IP address of the device, utilize the PING command as follows:

zStart a DOS window.

zType ping x.x.x.x, where x.x.x.x is the IP address of the device.

The replies, as illustrated below, will provide an explanation to the problem.

If you want to detect any other devices conflicts with the IP address of Network Camera, also can utilize the PING command but you must disconnect the device from the network first.

Contents User Manual Wired Internet Camera RXS-3323 Wireless Internet Camera RXS-4324FCC RF Radiation Exposure Statement FCC STATEMENTCE Mark Warning National RestrictionsChapter 2. Installation Table of ContentChapter 3. Connecting to the Camera Chapter 1. Product OverviewAppendix A Restore Factory Default Settings 3. Quick Installation Guide Package Contents5. RJ 45 Cable 6. 12V/1A Power Adapter 7. Camera Mount Kit Chapter 1. Product OverviewSystem Requirements Product Featuresz H2.64, MPEG4, and MJPEG Tri-Codec supported z 2-Way Audio CapabilityHighlights z Remote Control Supportedz Optimal Viewing z Supports Multiple Profileseasily Front View Introduction of HardwarePower and Wireless IR LEDsPower Jack Rear ViewAntenna Connector Factory Default ResetCamera LAN and Power Installation Hardware InstallationChapter 2. Installation Ceiling MountWall Mount Software InstallationIPWizard II Installation 4.Click on “Run” to continue 3.Please click on “IPWizard” under “Software & Tools” to continue6.Click on “Next” to continue 7.Click on “Finish” to finish the installationChapter 3. Connecting to the Camera Using IPWizardmanagement page in your default Web Browser Double Click on the above information bar will open up the Camera14. WiFi 9. WirelessOne click to view the video from theWireless Page You should see the confirmation Status Window popup as below. Please select “OK” to confirm these settings User Manual Three ways to access the Camera for the first time Access the device using IE for the first timeManaging the Camera Opening up UPnP in Win XPz Open Control Panel z Click on Network and Internet Opening up Network Discovery in Win7z Click on View Network Computers and devices Entering into Camera’s Management page via IE z Upon selecting the “Install This Add-on for All User on This Computer”, you will see an Security Warning Window asking your permission to install the Rosewill Media Control. Please click “Install” to continute Settings Management PageStreaming LanguageSnapshot 10. VolumeRecord 11. StatisticsNetwork SettingChapter 4. Managing the Device Network8. Secondary DNS 9. HTTP Port 1. MAC address 2. Obtain IP address automatically DHCP 3. IP address4. Subnet mask 5. Gateway 6. Obtain DNS from DHCP 7. Primary DNS 4. Interface Select 5. Type Wireless1. Setting Easy Installation 2. Site survey 3. MAC address 7. BSSID 6. SSID8. Channel 9. Security mode1. DDNS 2. Server name 3. DDNSHost 4. User name 5. Password DDNSStreaming PPPoE1. PPPoE 2. User name 3. Password 4. IP address, Subnet mask, and Gateway read only 5. Status1. RTSP Port 2. RTP Port UPnPIP Filter Bonjour1. UPnP 2. Friendly Name 3. UPnP NAT Traversal 4. Port Range 5. External IP address1. SMTP Notification e-mail 2. Send To 3. Subject IP NotificationPicture Camera8. HTTP Notification 9. URL 10. HTTP Login Name 11. HTTP Login Password 12. Proxy Address 13. Proxy Port6. Sharpness 7. Contrast 8. Night Mode 9. White-Light LED 2. White Balance 3. Exposure Control 4. Color Level 5. BrightnessLED ON Threshold 0~10000 LED OFF Threshold 0~1000010. De-Noise Preset SettingTour Setting System System1. Tour Name 2. Running 3. Preset 4. Wait Time 1. DIPS Dynamic IP Service 2. Device ID for DIPS6. Power LED Wireless LED 7. Log 8. Reload Date & Time3. Adjust 3. Device Title 4. Software Version 5. Network LED1. Hard Factory Default Include the network setting Maintenance2. Factory Default Except the network setting 3. Backup Setting 4. Restore Setting6. System Restart 5. Firmware Upgrade procedureCommon VideoVideo Profile 1. Text Overlay Setting 2. Video Profile4. GOP Control ROI 1 The area size of ROI 1 is H.264 / QVGA, 320 x ROI 0 The area size of ROI 0 is H.264 / VGA, 640 x1. Audio 2. Audio Mode 3. Input Gain 4. Output Gain AudioUser 1. SMTP Server 2. Test 3. SMTP Port 4. SMTP E-Mail3. Add, update, and remove of Users account Authentication 5. Authentication User name 6. Authentication Password Object Detection7. E-mail To 8. E-mail From 9. E-mail Subject 1. Add and Del 2. Included or Excluded Window 3. Name 4. Object SizeFTP Server Event ServerTCP Server 1. Name 2. FTP Server 3. Test 4. FTP Login name 5. FTP Login Password1. Name HTTP Server1. Name 2. TCP Server 3. TCP Port 2. URL 3. Test 4. HTTP Login name 5. HTTP Login Password SAMBA Server6. Proxy Address 7. Proxy Login name 8. Proxy Login Password 1. Name 2. SAMBA Server 3. Test 4. SAMBA Login name 5. SAMBA LoginEvent Schedule SettingPassword 6. SAMBA Path 1. Name 2. Enable 3. Type 4. Enable Time 5. Trigger by 6. Action1. Record File Type 2. Record File Prefix 3. JPEG Picture Numbers Record2. PTZ Adding Preset pointAdvance PTZ 2. Please right click on it and select “Temporarily Allow Scripted Windows” Selecting Tour Digital ZoomSnapshot Record VolumeRestore the device Appendix A Restore Factory Default SettingsFeatures Appendix B Troubleshooting & FAQInstall the Device QuestionUPnP Connection Access the DeviceNetwork Camera’s private IP address Video Quality of the Device Miscellaneous Appendix C Ping IP Address Image Resolution Appendix D Bandwidth EstimationAverage range of data sizes Average bit rate forAppendix E Specifications 0 ~ 355 180/ second MAX 1 Assign a local/fixed IP address to your device Appendix F Configure Port Forwarding Manually2 Access the Router with Your Web browser Your WAN IP will be listed here 3 Open/set Virtual Server Ports to enable remote image viewingPort section, click Apply Process of set up your own Domain Name Appendix G DDNS Configuration1 Environment of Fixed Valid IP Network 2 Environment of Dynamic IP Network3. After the columns show up at the left side, click “Create Account” c. Password and confirmation4. Fill the application agreement and necessary information a. Username b. E-mail address and confirmationUser Manual 9. Click the “ Dynamic DNS ” 8. Click the “Services”10. Click the “Get Started” iPhone Appendix H 3GPP and iPhone