Samsung AR09FSFTKWQNET Connecting the assembly cable, Cable specification, Connecting the cable

Page 32

Fixing the installation plate

2. Fix the indoor unit.

If you fix the indoor unit on a wall

(1) Fix the installation plate to the wall giving attention to the weight of the indoor unit.

• If you mount the plate to a concrete wall using plastic anchors, make sure that gaps between the wall and the plate, created by projected anchor, is less than 20mm.

Plastic

Anchor

<20mm

Wall

If you fix the indoor unit on a window frame

(1)Determine the positions of the wooden uprights to be attached to the window frame.

(2)Attach the wooden uprights to the window frame giving attention to the weight of the indoor unit.

(3)Attach the installation plate to the wooden upright using tapping screws.

If you fix the indoor unit on a gypsum board

(1)Use stud finder to find out locations of the studs.

(2)Fix the plate hanger on two studs.

• Search for other spots if there are less than two studs, or the distance between the studs are different from the plate hanger.

•Fix the installation plate without inclining to one side.

•Make sure that a wall can withstand the weight of the product. If you install the product in a place where it is not

strong enough to withstand the product weight, the unit could fall and cause injury.

Connecting the assembly cable

Cable specification

Model

Power cable

Interconnection cable

Type GL

 

 

 

 

 

 

 

 

 

 

09/12

3G2.5mm² H07RN-F

3G1.5mm² H07RN-F

20A

 

 

 

 

18/24

2x0.75mm² H05RN-F

25A

 

 

 

 

 

 

 

• Connect the power cable to the auxiliary circuit breaker. If every pole fails to connect to the

power supply, it must be incorporated in a wire with a contact opening of ≥3mm.

•Power supply cords of parts of appliances for outdoor use shall not be lighter than polychloroprene sheathed flexible cord. (Code designation IEC: 60245 IEC 66/CENELEC: H07RN-F, IEC: 60245 IEC 57/CENELEC: H05RN-F)

Connecting the cable

Electrical work

(1)For electrical and earth works, comply with the‘technical standards of electrical installations’and the the wiring regulations’of the Electricity Enterprises Act.

(2)Tighten the terminal block screw to 1.2 ~1.8 N•m (12 ~18 kgf•cm).

(3)Precautions when connecting terminal blocks of the indoor unit

Before connecting, make sure the connecting part of the terminal socket is facing upwards.

 

The terminal

There is no ring

Upside down

 

socketis damaged.

terminalto cover the wire.

There must be no space between the terminal and the screw when connected.

- Any remaining space may become a fire hazard due to overheating of the electrical contact.

 

 

Either the screw is not fitted

The terminal socket

properly or there is a space between

is upside down.

the screw and the ring terminal.

32

Boracay ET_AR09FSFT@_IBIM_DB68-03377A_EN-7.indd 32

2014/12/11 17:23:08

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Boracay ETAR09FSFT@IBIMDB68-03377AEN-7.indd 2014/12/11 Contents Safety precautions Important safety symbols and precautionsPersonal injury or death Personal injury or property damageFor Installation Caution For Using Do not touch the circuit breaker with wet hands Do not place objects or devices under the indoor unit Do not touch the pipes connected with the product Do not operate the appliance with wet handsDo not drink the water from the air conditioner For Cleaning Do not clean the inside of the air conditioner by yourselfChecking before use Operation rangesPower button Checking the name of the partsMain parts DisplayChecking the remote controller Remote controller buttonsRemote controller display Battery changing timeStoring the remote controller Inserting the batteriesBasic function Button to adjust the temperature PressAdjusting the air flow direction Using the Turbo functionPress the Air swing button on the remote controller Vertical air flowWhen the air conditioner is on and in cool/heat mode Press the button on the remote controllerMode Press the Time Up or Time Down button to set the timeSetting the On/Off timer Press the On Timer/Off Timer buttonCancel Press the Cancel button Additional options available in On timer modeUsing the Smart Saver function From the moment you have set the timerIf the air conditioner is on If the air conditioner is off Turn off automaticallyUsing the Quiet function Using the Auto Clean functionWhen the air conditioner is turned on You can reduce the noise generated from an indoor unitCleaning the air conditioner Make sure the power is turned off and unplugged fromCleaning the indoor unit Cleaning the outdoor unit heat exchangerCleaning the air filter Removing the Air filterOpen the panel and put the Air filter out Dry the Air filter in a ventilated areaClean the condensate drain pan Maintaining the air conditionerTroubleshooting Working Cannot adjust the temperature Fan speed Timer functionIndicator Air flow Check if you have selected Auto/Dry Mode.General information Included Models RemarkChoosing the installation location Installing the unitPower supply line, fuse or circuit breaker  a place where the air filter can be replaced easilyWhere sulfide gas exists Outdoor UnitWhen installing more than 1 outdoor unit When the air outlet is towards the wall Figure Description Top view Side viewAccessories in the outdoor unit case AccessoriesAccessories in the indoor unit case Fixing the installation plate Optional accessoriesTools required for installation General Tools Tools for test operationsConnecting the cable Connecting the assembly cableCable specification Extend the assembly cable if necessary Each wire is labeled with the corresponding terminal numberSmooth the cut edges Cut off the remaining foam insulationPurging the indoor unit Cutting or extending the pipeUnscrew the caps at the end of each pipe Put a flare nut slightly into the pipe and modify the flarePipe 50 Pa. The joint must be accessible and serviceable Correct InclinedCracked Outer DiameterDrain hose installation Changing direction of the drain hoseEnsure that condensation draining is adequate Purging the connected pipesConnect a drain hose to the drain plug Adding Refrigerant If you use a pipe longer than 5mIf you use a pipe shorter than 5m Model2088 Please fill in with indelible ink the factory refrigerant charge of the product Performing the gas leak tests To check for gas leaks on the outdoor unitTo check for gas leaks on the indoor unit Leak test with nitrogen before opening valvesOutdoor unit installed on the wall by rack Then place the indoor unit on the installation plateFixing the indoor unit in place Fixing the outdoor unit in placeFinal Check and Trial Operation How to connect your extended power cables Apply heat to the contraction tube to contract itAfter tube contraction work is completed, wrap it with Insulation tape to finishEnglish Questions or COMMENTS? Air Conditioner
Related manuals
Manual 45 pages 3.43 Kb Manual 47 pages 32.01 Kb Manual 45 pages 23.12 Kb Manual 1 pages 28.11 Kb Manual 45 pages 45.25 Kb Manual 1 pages 30.65 Kb Manual 45 pages 732 b Manual 43 pages 53.57 Kb Manual 45 pages 260 b Manual 1 pages 28.15 Kb Manual 1 pages 28.19 Kb Manual 1 pages 28.11 Kb Manual 1 pages 28.18 Kb

AR12FSFTKWQNZE, AR09FSFTKWQNET, AR12FSFTKWQNET, AR12HSFTKWQNET, AR12FSFTJWQNET specifications

The Samsung AR09HSFTKWQNET and AR09HSFTKWQXET are two standout models in Samsung’s line of air conditioning units, designed to deliver powerful cooling and energy efficiency in residential and commercial spaces. Both models incorporate advanced technologies and user-friendly features that enhance user comfort while minimizing energy consumption.

One of the main features of these units is their use of Digital Inverter Technology. This innovative system maintains the desired temperature without frequent on-off cycling, reducing energy consumption by up to 60% when compared to traditional air conditioners. The Digital Inverter allows the compressor to adjust its speed based on the cooling demand, ensuring a consistent and comfortable environment without dramatic fluctuations in temperature.

In addition to energy efficiency, the Samsung AR09HSFTKWQNET and AR09HSFTKWQXET are equipped with a powerful air filtration system. The Triple Protection Filter not only captures dust and allergens but is also easy to clean and maintain. This means that indoor air quality remains high, making these units particularly suitable for allergy sufferers and those looking for a cleaner living environment.

The design of both models blends seamlessly with any decor, featuring a sleek and modern exterior. The additional LED display allows users to monitor settings easily, further enhancing the user experience. Each model comes with a remote control, enabling the user to adjust temperature and settings from anywhere in the room.

Noise levels are another key characteristic of the Samsung AR09HSFTKWQNET and AR09HSFTKWQXET. These air conditioners operate quietly, making them ideal for bedrooms and workspaces where noise disruption is not welcome. This is further enhanced by the indoor units’ acoustic insulation, which minimizes sound transmission.

Another remarkable aspect is their quick cooling function. With the option to reach the desired temperature rapidly, users can enjoy immediate relief from heat, making these air conditioners perfect for hot climates.

To underscore their commitment to sustainability, Samsung designs these models with eco-friendly refrigerants, further contributing to lower environmental impact while still maintaining high performance.

In summary, the Samsung AR09HSFTKWQNET and AR09HSFTKWQXET embody cutting-edge technology combined with user-centric features. Their energy-efficient operations, advanced air filtration, stylish design, and quiet functioning make them an excellent choice for anyone seeking a dependable and effective cooling solution.
Top Page Image Contents