Samsung SCC-C6407P Auto SET, AUX OUT Control, Alarm Priority SET, Alarm in SET, Alarm OUT SET

Page 28

6. ALARM SET

It consists of 8 ALARM INPUTs and 3 ALARM OUTs.It can sense an ALARM input from exterior SENSORs and it performs with PRESET or PATTERN function and outputs the ALARM OUT signals.

The Alarm will be recognized only when its input lasts more than 150ms and the alarm operation time depends on the Preset Dwell time corresponding to the alarm and whether AUTO is involved.

AUTO SET

This menu designates what to do at the time of ALARM input. Once an alarm is given, the camera will shortly move to the PRESET position corresponding to the respective alarm as follows.

PRESET1 to ALARM1~8 PRESET9 to MOTION

After DWELL TIME at a PRESET position, PATTERN or SCAN will be in action according to the AUTO SET setup.

Setup of OFF/1/2/3/HALF1/HALF2/FULL/SCAN1~4 is available.

OFF dues not perform PATTERN or SCAN after moved to PRESET and each menu has its own function as follows.

E

* * MAIN MENU * *

CAMERA SET...

VIDEO SET...

PRESET...

ZONE SET...

AUTO SET...

ALARM SET...

OTHER SET...

SYSTEM INFO...

Press [Enter]

( ALARM SET)

ALARM PRIORITY SET ...

ALARM IN SET.. ALARM OUT SET.. AUTO SET..

AUX OUT CONTROL..

RET

PATTERN 1~3 : Preset PATTERN action,

HALF1 : Continuous operation of PATTERN1 + PATTERN2

HALF2 : Continuous operation of PATTERN2 + PATTERN3

FULL : Continuous operation of all the aboves

SCAN 1~4 : Scanning as set

AUX OUT CONTROL

This sets the ALARM OUT motion to continue or act only when the ALARM is working.

ALARM PRIORITY SET

This sets the priority of the 8 ALARM inputs so ALARM can work corresponding to the priority.

The priority of the DEFAULT is ALARM1, ALARM2, ALARM3, ALARM4, ALARM5, ALARM6, ALARM7, ALARM8.

If the ALARM is working at the same time and the priority is the same, it will operate according to the DEFAULT priority. While the ALARM is working, it cannot detect MOTION.

ALARM IN SET

This sets the input TYPE to "NO" (Normal Open), "NC" (Normal Close), or "OFF" depending on the features of the SENSOR connected.

ALARM OUT SET

Each ALARM input corresponds to one of the 3 ALARM OUT.

If it is set to OFF the ALARM OUT motion will operate only when the ALARM is working.

(Active "Low"), and if it's set to ON, the ALARM OUT will always operate regardless of the ALARM.

7. OTHER SET

PROPORTIONAL P/T

This function controls the PAN/TILT speed to the ZOOM magnification ratio during the manual operation of PAN/TILT. If you set PROPORTIONAL P/T to ON, the PAN/TILT speed will increase in the ZOOM WIDE mode and decrease in the ZOON TELE mode even in the same manual operation.

3-29

3-30

Image 28
Contents SCC C6407P Important Safety Instructions FCC Statement Before Usage Table of contents Chapter Locations of Control Adapter Connection Initial Setting Camera Address SetupBaud Rate Setting Use PIN 5 and 6 of SW704 Factory default setting is set to 9600BPSCC- C6407P Installatio n Before Installing Ceiling Mount Bracket SBR-100DCM Wall Mount Adaptor SADT-100WMIndoor Housing SHG-120 Outdoor Housing SHG-220Ceiling Mount Adaptor SADT-100CM Pole Mount Adaptor SADT-100PMInstalling the Camera Setup Menu Overview Camera ID Screen will be displayedCOLOR/BW SyncAuto LevelMotion DET Zoom SpeedDigital Zoom ExitIris ALCShutter ManuWDR AGC MotionWhite BAL AGC GainDIS Focus ModeDetail Preset ID Preset SpeedPosition SET Video SETBlank ALL Above Blank ALL belowPrivacy Zone MAP Privacy ZoneSET Zone Area SET ZoomReverse Zone DIR SET/ZONE Area SETZone Enable Zone DIR SETLocation Zone AreaAuto PAN DirectionEndless SpeedAuto Play ScanAuto Return Play NumberAlarm Priority SET Alarm in SETAlarm OUT SET Auto SETCAM Reset PasswordTurbo P/T Auto CALShort Keys Product specifications Page SCC C6407P Warnung SicherheitshinweiseAchtung Kapitel 3 Überblick über das Setup-Menü erläutert die Vor InbetriebnahmeInhaltsverzeichnis Adapteranschluss ErsteinstellungKapitel 1 Ü b erb lick über die SC C -C6407 P Einführung in die SCC-C6407PSteuerungselemente Verwenden Sie PIN 5 und 6 von SW704 AdapteranschlussDie Werkseinstellung beträgt 9600 bps Kapitel 2 I n stallation der SC C -C6407 P Einstellung der RS-422A/RS-485 AbschlüsseVor der Installation Vorbereitung der KabelInstallation der SCC-C6407P KabelanschlüsseDeckenhalterung SBR-100DCM Wandhalterung SADT-100WMDeckenhalterung SADT-100CM Masthalterung SADT-100PMInstallation der Kamera Bild 7 Stecken Sie passend aufAp itel 3 Ü ber blick über das Setup Men ü Aufbau des Setup MenüsKamera Prog Menü Kamera IDFARBE/S/W Sync…bedeutet, es gibt Untermenüs Mittel und HochAktivität Zoom GeschVideo PROG-Menü Shutter ManuWDR Motion AGCWeissabgl Spezial Fokus ModeDIS Preset Zone Prog Zone Setzen Zoom SetzenRevers Richtung SETZEN/ZONE GesetztRichtung Setzen PositionZone Gesetzt Zone ID SetzenAuto Prog Auto Modus ScanAuto Zurück FunktionsnummerAlarm Prog Weitere ProgSystem Info Alarm FAN Error Camera FAN ErrorKurztasten Technische Daten SCC-C6407Korrekte Entsorgung dieses Produkts Elektromüll Manuel d’instruction Avertissement Précautions de sécuritéMise en garde Avant l’utilisation Table des matières SCC-C6407P Introduction Chapitre 1 S C C- C6407P vue d’ense mbleConnexion d’adaptateur Utilisez les Broches 5 et 6 du SW704 Arrangement de commutateurPar défaut, lappareil est réglé sur 9 600 BPS Chapitre 2 S CC- C6407P Installat ion Arrangement de RS-422A/RS-485 d’une terminaisonAvant l’installation Préparation des câblesInstallation de la camera SCC-C6407P Connexion de câbleSupport DE Fixation AU Plafond SBR-100DCM Support DE Fixation AU MUR SADT-100WMBoîtier D’INTÉRIEUR SHG-120 Boîtier D’EXTÉRIEUR SHG-220Support DE Fixation AU Plafond SADT-100CM Bride DE Montage SUR Poteau SADT-100PMInstallation de la Camera BRKT-ancre et l’adaptateur deConnecteur et tournez-la à gauche environs 15degrés DômeChapitre3 Vue d’ensemble de menu d’installation Contenu de menu d’installationProg Camera Camera ID’écran suivant s’affichera HAUT/BAS/GAUCHE/DROITECouleur AGC COULEUR/N&BHaut Zoom Vitesse DET MouveDET Mouve Prog Video Zoom DigitalCjour SortieALC Cjour Util Niveau RET Mouve CAGBAL Blancs Mode Focus Mode FocusSpecial UtilPreset Vitesse Prog PositionProg Video VIT CycleProg Zone Masque LE HautMasque Dessous Liste Z. PrivReglage Zoom Reglage ZoneREG DIR ZONE/DEF DES Zones REG DIR Zone DEF DES ZonesREG. N DE Zone Zone EN FonctionPRO Auto Lecture Auto BalayageRET Auto Lecture Auto NProg Alarme Autre ProgInfo Systeme Raccourcis Fonction ToucheSpécification du produit SCC-C6407Mises en garde Manual del usuario Medidas de seguridad AdvertenciaPrecaución No coloque encima de la cámara objetos conductoresAntes de Instalar el equipo Indice Capí tulo 1 C a rac terísticas del SC C C64 07P Introducción del SCC-C6407PLocalización de controles Conexiones del adaptador Ajustes Iniciales Use PIN 5 y 6 del SW704Cap ítulo 2 I nstalación del SC C C640 7P Ajuste de la terminación RS-422/RS-485Antes de la instalación Preparación del cableConexión del cableado Instalación de la cámara SCC-C6407PSoporte DE Montaje Para Techo SBR-100DCM Adaptador DE Montaje EN Pared SADT-100WMCubierta Para Interiores SHG-120 Cubierta Para Exteriores SHG-220Adaptador DE Montaje EN Techo SADT-100CM Adaptador DE Montaje EN Poste SADT-100PMInstalación de la cámara Figura 2 Instale el soporte en U con 4 tornillosCapít ulo 3 Menú de ajust es Estructura del menú de ajustesProg Cámara Cámara ID…Significa que hay submenús COLOR/ByNSeg L DET Movi VEL ZoomBLC Submenú del menú ALC/MANU SalidaDiafragma Predefinida pulsando la tecla Entrar en el estado ARRIBA…Obturador Movimiento BAL BlancoFoco Modo UnoafSer necesario usar los botones de Foco del teclado Es igual que la función Salida del menú de la Cámara SETPreset ID Identificación del preset Preset VelocidadProg Posición Ciclo TiempoProg Zona Fijar Area DE Zona Fijar ZoomReverso Fijar DIR ZONA/FIJAR Area DE ZonaFijar DIR Zona PosiciónFijar Area Zona Fijar ID ZoneProg Auto DireccionSIN FIN SpeedAuto Reprodu Cción Vuelta AutoBarrido REP. NúmeroAlarma Prog Altra ProgReset CÁM Auto CALIdioma ContraseñaAlaram FAN Error Claves CortasEspecificaciones de producto ContenidosAtención Sistema DE Color Estándar PALIstruzioni per l’uso Avvertenza Norme di sicurezzaAttenzione Prima dell’uso Indice Impostazioni PreliminariCapitolo 1 D es c rizione di SCC -C640 7P Introduzione al modello SCC-C6407PCollocazione dei comandi Relay esterno Impostazioni PreliminariUtilizzare i PIN 5 e 6 di SW704 Il valore preimpostato in fabbrica è 9600BPSImpostazioni di terminazione RS-422A/RS-485 RS-422A/RS-485 in duplexPrima dell’installazione Preparazione dei caviInstallazione della telecamera SCC-C6407P Connessione del cavoStaffa PER IL Montaggio a Soffitto SBR-100DCM Adattatore PER IL Montaggio a Parete SADT-100WMAlloggiamento Interno SHG-120 Alloggiamento Esterno SHG-220Adattatore PER IL Montaggio a Soffitto SADT-100WM Adattatore PER IL Montaggio SU Palo SADT-100PMInstallazione della telecamera CupolaAp ito lo 3 Descrizione del menù di Setu p Struttura del menù di SetuID Camera Menu Prog CameraSchermo seguente sarà essere esposto Colore B/N Indica la presenza di sottomenùActivity DET Impostazione dell’area, eccMenu Prog Video Zoom DigitaleUscita EsciALC BLC Util Livello RET BIL Bianco Modo Focus SpecialeInserire input manuali AutomaticaPreset VELOCITA’ Prog PosizioneTempo DI Scan IMG HoldCANC. Parte INF Mappa PRIV.ZONE Privacy ZoneStile Privacy ZoneImposta Zona Imposta ZoomReverse Imposta DIR. ZONA/IMPOSTA ZonaImposta DIR. Zona PosizioneID Zona Attivo Zona AbilitataDirezione ContinuaVELOCITA’ PercorsoScansione AUT ScansioneRIT POS Auto Richiama FunzioneProg Allarmi CAM Reset PasswordInfo Sistema LinguaChiavi Corto Funzione ChiaveSpecifiche di prodotto RimarcaAvvertenze Contenuto Rimarca
Related manuals
Manual 94 pages 43.56 Kb