Samsung AQV09EWEN, AQV12EWEN, AQV09EWEX Mode, When the air conditioner is on and in cool/heat mode

Page 13

mode

For a comfortable sleep, the air conditioner will operate it Fall asleep Sound sleep Wake up from mode.

When the air conditioner is on and in cool/heat mode

1. Press the button on the remote controller.

indicator appears and Off timer indicator starts blinking on the remote controller display.

2. Press the button to set the time.

You can set the time in half hourly unit from 30 minutes ~ 3 hours and hour unit from 3 hours ~ 12 hours.

Operating hour can be set from minimum 30 minutes to maximum 12 hours. Default operation hour is set to 8 hours.

3. Press the Set/Cancel button to active it on.

Off timer indicator stops blinking and reserved time will be displayed for 3 seconds. Then the air conditioner operates in good’sleep(Cool) mode.

If you don’t press Set/Cancel button within 10 seconds after pressing the , the air conditioner will return to previous status.

ENGLISH

Cancel Press the Set/Cancel button once again.

You can set the desired temperature by 1˚C in the range of 16˚C~30˚C.

Fan speed will be adjusted automatically according to the mode.

However, I f you select mode while heating operation is on, you can adjust fan speed.

Air flow direction will be adjusted automatically according to the mode.

However, if you select mode while heating operation is on, you can adjust air flow direction.

Temperature and fan speed changes in mode

Fall asleep: Eases you into sleep by dropping the temperature.

Sound sleep: Relaxes your body and raises your temperature slightly.

Wake up from mode: Allows you to wake up from comfortable intermittent air and it makes you feel refreshed.

• Set Off timer in

mode over 5 hours. You fell disturbed sleep if the

is set too short or long

because the default is set to 8-hour-operation.

 

If the mode is set less than 4 hours, the operation will stop at the same time.

If the mode is set over 5 hours, it will run as Wake up stage from the last one hour before it stops.

Recommended set temperature is between 25˚C~27˚C for cooling and 21˚C~23˚C for heating.

13

Vivaldi Cystal EUR_AQV09E@@ IB&IM_32449A_E.indd 13

2011-3-7 15:44:58

Image 13
Contents Vivaldi Cystal EURAQV09E@@ IB&IM32449AE.indd 2011-3-7 Contents Important safety symbols and precautions Safety precautionsFollow directions Wall socketFor Using For Cleaning Operation ranges Checking before useChecking the name of the parts PowerMain parts DisplayRemote controller buttons Checking the remote controllerBattery changing time Remote controller displayStoring the remote controller Inserting the batteriesBasic function Press Button to adjust the temperatureUsing the Turbo function Adjusting the air flow directionPress the Air swing button on the remote controller Vertical air flowPress the button on the remote controller When the air conditioner is on and in cool/heat modePress the Set/Cancel button to active it on ModePress the On Timer/Off Timer button Setting the On/Off timerPress the On Timer/Off Timer button to set the time Using the Smart Saver function Using the SPi functionUsing the Auto Clean function Using the Quiet functionWhen the air conditioner is turned on You can reduce the noise generated from an indoor unitCleaning the indoor unit Cleaning the air conditionerCleaning the outdoor unit heat exchanger Opening the panelRemoving the Air filter Cleaning the air filterOpen the panel and put the Air filter out Dry the Air filter in a ventilated areaPeriodical checks Maintaining the air conditionerTroubleshooting Flow movement changes. It is normal Outdoor unit Heat exchanger during Heat mode in winterConnection Included Models Remark General informationAQV09E, AQV12E, AQV18E, AQV24E Installing the unit Choosing the installation locationPower supply line, fuse or circuit breaker  a place where the air filter can be replaced easilyOutdoor Unit Where sulfide gas existsWhen the air outlet is towards the wall When installing more than 1 outdoor unit Figure Description Top view Side viewAccessories in the indoor unit case AccessoriesAccessories in the outdoor unit case Optional accessories Fixing the installation plateTools required for installation General Tools Tools for test operationsCable specification Connecting the assembly cableConnecting the cable Each wire is labeled with the corresponding terminal number Cut off the remaining foam insulation Smooth the cut edgesCutting or extending the pipe Purging the indoor unitUnscrew the caps at the end of each pipe Put a flare nut slightly into the pipe and modify the flareCorrect Inclined Pipe 50 Pa. The joint must be accessible and serviceableCracked Outer DiameterDrain hose installation Connect a drain hose to the drain plug Purging the connected pipesEnsure that condensation draining is adequate Adding Refrigerant  the factory refrigerant charge of the product Please fill in with indelible ink1975 To check for gas leaks on the outdoor unit Performing the gas leak testsTo check for gas leaks on the indoor unit Leak test with nitrogen before opening valvesThen place the indoor unit on the installation plate Outdoor unit installed on the wall by rackFixing the indoor unit in place Fixing the outdoor unit in placeFinal Check and Trial Operation Apply heat to the contraction tube to contract it How to connect your extended power cablesAfter tube contraction work is completed, wrap it with Insulation tape to finishEnglish 7267864, € 0.07/min 42 2770 70 19 +381Air Conditioner
Related manuals
Manual 23 pages 41.95 Kb Manual 23 pages 55.9 Kb Manual 25 pages 14.93 Kb Manual 39 pages 27.14 Kb