Crimestopper Security Products CS-882 OEM Wiring, WHITE/RED Negative HORN/SIREN Output

Page 3

WIRING

(2) VIOLET WIRES: ON-BOARD RELAY (10A) IMMOBILIZER CIRCUIT #1 NORMALLY OPEN

These wires come directly from the terminals of an on-board Relay to immobilize the Coil or Fuel Pump Circuit in the vehicle. Selected the circuit you want to interrupt, cut it, and connect each cut end to a VIOLET wire.

NOTE (1): This is a high-security, normally open connection. If the alarm system is unplugged or loses power, the circuit will still be immobilized!

NOTE (2): This circuit has a maximum load of 10A and should NOT be used to interrupt a high current wire such as an Ignition supply or Starter circuit from the ignition switch!

WHITE/RED: (-) NEGATIVE HORN/SIREN OUTPUT

Connect to wire that activates the factory horn. If you choose to use this output with a standard alarm (warble) siren, then it should be connected to the black (negative) wire of the siren. Connect the red wire of the siren to constant (+) 12 Volts. NOTE: This wire is preset for a factory vehicle horn. You must change the programming for siren use. See option #15.

BLACK WIRE: SYSTEM CHASSIS GROUND

THIS WIRE MUST BE CONNECTED TO CHASSIS METAL OF THE VEHICLE. Scrape away any paint or dirt from the area to ensure a good connection.

RED WIRE: +12V POWER INPUT (15 amp fuse)

Connect to +12 Volt source with supplied fuse & holder. Connect to the vehicle’s battery Positive terminal.

(2) WHITE WIRES: +12V FLASHING PARKING LIGHT OUTPUTS (15 amp fused)

Connect ONE of the white wires to the switched parking light wire at back of light switch, the kick panel or fusebox. If these locations are not possible, connect directly to one of the parking lights at the front of the vehicle.

NOTE: Many European vehicles require separate right and left circuits. Use this second white wire to connect to the 2nd light circuit on your European vehicle, otherwise do not use both white wires.

ORANGE WIRE: (-) NEGATIVE STARTER DISABLE (Armed output)

Ground output when system is armed. This output is used for disabling the starter or to activate other optional devices such as scanner LED’s, window control modules, voice modules etc. For starter kill, cut starter wire and connect between 87A and 30 on a relay. Connect orange wire to 85 and connect 86 to an Ignition source that has voltage in “ON” and “CRANKING” positions at the Ignition switch. (Starter disable relay not included)

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents CS-882 OEM Table of Contents Installation Precautions & WarningsComponent Mounting Orange Wire Negative Starter Disable Armed output WiringBlack Wire System Chassis Ground RED Wire +12V Power Input 15 amp fuseYellow Wire +12 Volts Ignition Switched Page Mode a is the default mode and is used for most vehicles Installation Mode a Most VehiclesMode B Wiring Diagram Resistors and Diodes are included Installation Mode BViolet Door Warning Delay Programmable OptionsFlashing Lights Passive Arming Panic ModeOption Reset SIREN/HORN ConfirmationOperating Instructions Factory Trunk Release Sensing Valet ModePanic Mode Programmable Option Operating Insructions

CS-882 OEM specifications

Crimestopper Security Products has long been a trusted name in vehicle security, and their CS-882 OEM model exemplifies their commitment to providing reliable, advanced safety solutions. The CS-882 is a comprehensive security system designed specifically for ease of use and peak performance, tailoring design elements to fit seamlessly into most vehicle types.

One of the standout features of the CS-882 is its two-way communication system. This allows owners to receive real-time alerts about their vehicle's security status, enhancing peace of mind whether the vehicle is parked at home or in a crowded parking lot. The system incorporates a range of advanced sensors, including a shock sensor that gauges impacts or disturbances. This helps prevent unauthorized access or tampering, protecting the vehicle and its contents effectively.

The CS-882 also boasts a remote start capability. This not only adds convenience for users, enabling them to start their vehicle from a distance, but also increases security by allowing users to heat or cool their vehicle while maintaining safety. This remote start functionality can also be integrated into modern vehicles equipped with push-start ignition systems, showcasing its versatility.

Another integral feature is the keyless entry system, which enhances user accessibility. This technology eliminates the need for traditional keys, allowing users to unlock their vehicles with a simple button press, which is especially useful in scenarios where carrying a key might be cumbersome. The system is designed for reliability and speed, ensuring that access to the vehicle is quick and efficient.

In terms of its build quality, the CS-882 OEM is constructed from durable materials to withstand the rigors of everyday use. It features a compact design that ensures easy installation without compromising the internal aesthetics of the vehicle. The system is designed for compatibility with various car makes and models, making it highly versatile.

Additionally, the CS-882 uses advanced technology to minimize false alarms, which can be a nuisance in standard alarm systems. This ensures that users receive alerts only for genuine threats, maintaining the system’s effectiveness and reliability. Overall, Crimestopper's CS-882 OEM model stands out as a robust vehicle security solution, combining advanced technology, user-friendly features, and solid construction to protect your vehicle from theft and unauthorized access.
Top Page Image Contents