Crimestopper Security Products CS-2014DP-TW2-FM Tach Mode & Tach Finder Feature, Tach Programming

Page 17

TACH MODE & TACH FINDER FEATURE

Tach Reference Mode provides reliable remote starting performance though engine speed sensing. When using Tach Reference Mode, the WHITE/RED wire is used for Tach signal [Engine RPM] input. Most modern engines include various points where the Engine Speed [Tach] or A/C signal may be obtained. Tach Signal examples: Negative (-) side of ignition coil, at the Distributor or Ignition Control Module, Coil Pack, Engine Computer, or Crankshaft Sensor. Sometimes Fuel injection solenoids and Alternator stator pins can be used. These Tach Signal locations mentioned are provided as a guide, your vehicle may differ. Some locations will NOT be a good location for Tach source due to RF noise or Computer Data. Use the TACH FINDER feature if needed.

TACH FINDER FEATURE:

The Tach Finder mode can assist you in locating or verifying a Tach source for your installation. Follow the Tach Finder steps below to locate signal. The unit will begin to flash the parking lights if you have the White/Red wire connected to a valid tach source. If lights do not flash, then try another wire until you locate a tach signal that will cause the Parking lights to flash. NOTE: On vehicles equipped with daytime running lights, it may be difficult to see any flashing parking lights. In this case your only notification will be the slight “ticking” sound coming out of the module from the on-board flashing light relay.

TACH FINDER:

1.Open hood (Ground the Blue Hood Pin wire if no hood pin is installed)

2.Start Engine with the key. (Pink ignition wire must be connected)

3.Press the Program button for 2 seconds

4.Lights will begin flashing if the White/Red wire is connected to a valid tach

5.Once Tach is located then turn off engine and close hood to abort.

6.See Tach Reference programming below.

TACH PROGRAMMING:

1.Open hood (Ground Blue wire if no hood pin installed.)

2.Connect WHITE/RED wire to a valid Tach source.

3.Start engine with key. (Pink ignition wire must be connected)

4.Press program button 5 times, then wait for 5 light flashes.

5.Wait at least one second then push program button again (1) time, you should get a light flash with the button press. This unit is now at option #1 for Tach Learning.

6.Press the #1 Lock Button on remote transmitter to program Tach. NOTE: Pressing the Brake Pedal also programs Tach. One Light Flash = Tach Mode. Two Light Flashes = Tachless Mode.

7.If lights do not flash for confirmation, then try another tach source or try the tach finder feature above.

17

Image 17
Contents Disclaimer IntroductionPR PRE-INSTALLATION Considerations Table of ContentsComponent Mounting Green Mode a Start Activation Input Wiring 9-PIN ConnectorGreen Mode B Optional Turbo Timer Input Brown + Siren OutputNegative Auxilary Output +12V Constant Starter Disable Orange Negative Starter Disable/Anti-Grind OutputWiring 6-PIN High Current Connector Wiring 3-PIN ConnectorIGN Violet + Door Pin Switch Input Wiring 5-PIN ConnectorGreen Door Pin Switch Input Blue Hood/Trunk Pin Switch InputWhite +12V Brake Reset Wiring 2-PIN LED / 2-PIN Program-Valet Button 22 gauge wiresSensor Adjustment Wiring 4-PIN Shock Sensor 22 Gauge wiresYELLOW/BLACK OEM Rearm Output Wire 4 PIN Output ConnectorBLUE/ORANGE Starter #3 BLUE/ORANGE Starter VIOLET/WHITE AUXRED +12V Coil Power for external relays Power Door Locks Wiring & System TypesDoor Lock Wiring Negative Trigger Door Locks Separate DRIVER’S Door Unlock WiringImportant Notes Tachless ModeTachless Adjustment Tach Finder Feature Tach Mode & Tach Finder FeatureTach Finder Tach ProgrammingHOW to USE this Feature Timed Crank ModeTo Engage Option Programming Diesel Glow Plug DelayProgrammable Options Option Programming Table Programmable Option Descriptions Second +1 SecondEngine Monitoring AUTOLOCK/UNLOCK W/IGNITIONPassive Locks Programmable OptionsParking Lights on with Disarm Siren Chirps with Remote Start ActivationDouble Unlock Pulse Door LOCK/UNLOCK Pulse TimeLock DURING/AFTER Remote Start No Option / not UsedFactory Horn Chirps / Pulses Diesel Glow Plug DelayULTRA-SMART Tachless Voltage Adjustment Aux #4 Time control 1 sec. to 255 sec. Default = 12 seconds Programmable Option ResetOption Reset Restore to Default Programming Transceivers & TransmittersRemote Programming Diagram Vehicle #2 Control Vehicle OperationRemote Start Diagnostics Alarm Trigger DiagnosticsSecuring Jumpers Jumper PIN DiagramAntenna Diagram Select Wiring DiagramData Port Diagram
Related manuals
Manual 32 pages 22.27 Kb