Oreck XL2700RH, XL2700HH How to Replace a Worn Belt, Stuffing or Blockage, Fan Housing Ring

Page 6

E N G L I S H

How to Replace a Worn Belt

WARNING: Unplug cord from electrical outlet before servicing.

Remove the replacement belt from the storage channel.

Stuffing or Blockage

Under certain conditions it is possible to stuff or block the intake tube and the lower tube assembly. If your vacuum cleaner does not pick up properly, or makes unusual noise and the outer bag does not fluff up or balloon open, follow the following steps:

WARNING: Unplug cord from electrical outlet before servicing.

NEW PHOTO

NEW PHOTO

Remove the door by removing the hold down screw located on side of power head.

Slide the door forward by prying open with a screwdriver or coin.

Remove the belt from the brush roll pulley and the motor drive shaft.

Loop the new belt over the motor drive shaft. Place the opposite end of the belt on the top of the brush pulley and roll the belt around the pulley.

Rotate the brush roll three

(3)complete revolutions to ensure the belt is properly seated behind the belt retainer.

Replace the door by sliding it into the groove at the bottom of the housing. Replace the hold down screw.

A

Intake Opening

B

Intake Opening

 

 

 

Retainer

 

Spring

C

Fan

Housing

O-ring

D

E

1.Check for blockage at the mouth of the intake opening. See illustration A. If there is blockage, remove it with long-nose pliers, a screwdriver or coat hanger. If you can not reach the blockage, remove baseplate. See illustration B.

2.If the blockage is not at the base, remove lower tube. See illustration C. Unhook retainer spring, releasing bottom of bag. Twist lower collar counterclockwise to slide up. Pull tube out of base. Check for blockage. If blockage is in the tube, remove with a coat hanger.

3.If tube is not blocked, look into fan housing. See illus- tration D. Remove debris with long-nose pliers, a screwdriver or coat hanger.

4.To reassemble, check O-ring on tube, and replace if damaged. Vacuum will not operate properly without the tube O-ring. Slide O-ring to approximately 2" from base of tube. Replace tube by first lining up slot at base of tube with inner tab inside fan housing. Then reinsert tube and push down until the tube is seated. Make sure O-ring is in place against fan housing opening. Replace and tighten collar until collar locking tabs are locked in place. See illustration E. Make sure collar is not cross threaded on housing.

6

Image 6 Contents
XL2600HH XL2610HH XL2700HH XL2700RH Important Safety Instructions Warranty Troubleshooting GuideAssembly Operating Instructions Door To Replace Filter Dust BagBag often Slide the cardboard collar completely onto bag dockFan Housing Ring How to Replace a Worn BeltRemove the replacement belt from the storage channel Stuffing or BlockageBulb Replacement To Adjust or Replace BrushUsing a Fresh Air Tab Connector Deflector OpeningEntretien et service La clientèle AccessoiresTable des matières Garantie Avis de fiche polariséeFiche polarisée Cordon d’alimentation Ressort de retenue Guide de dépannage AssemblageTube inférieur Tête motorisée Sac extérieur Fermeture à glissière Interrupteur principalMode d’emploi Remplacement du sac à poussières filtrant Remplacement d’une Courroie uséeRemplacement de l’ampoule électrique Blocage ou bourrageUtilisation d’une Tablette Oreck Fresh Air Réglage ou remplacement Du balai ¡GUARDE Este FolletoàAccesorios IndiceMantenimiento y servicio Clientes Aviso de la clavija polarizadaGuía para identificación De problemas GarantíaGancho de plástico/abrazadera para el cable Ensamblaje Para reemplazar la Bolsa para polvo de filtroEnsamblaje de la conexión Bastidor del ventilador Deslice el collarín de cartón en la puerta de carga de laInstrucciones de operación Cómo reemplazar una Correa desgastada Para ajustar o reemplazar El cepilloReemplazo de la bombilla Relleno o bloqueoUso de una tableta Anillo tórico