Heatiator I80 owner manual Secure the Fireplace, Install the Refractory, Position the Fireplace

Page 15

B. Secure the Fireplace

•Position the Fireplace

This fireplace may be placed on either a combustible or noncombustible continuous flat surface. Follow the in- structions for framing in Section 3.D. Slide the fireplace into position. Be sure to provide the minimum air clear- ance at the sides and back of the fireplace assembly. See Section 3.B.

WARNING

Fire Risk!

•Prevent contact with sagging, loose insulation.

•Do NOT install against vapor barriers or exposed insulation.

•Remove smoke shield by removing five screws. See Figure 4.7. Smoke shield is located at top of fireplace front.

•Remove screens by removing screw from the end of each screen rod. See Figure 4.8.

 

Smoke Shield

Front Face

 

Skip

Skip

Remove these screws.

Figure 4.7 Removing Smoke Shield

C. Install the Refractory

We recommend two installers for hearth stone and refrac- tory installation!

•Remove back refractory from outside of fireplace by bending tabs up and lifting refractory out of brackets. See Figure 4.5. Bend tabs back down out of the way. See Figure 4.6. Do not remove screws or brackets from fireplace. If brackets are removed, fill holes in outer shell with screws. Repeat this process to remove side refractories.

•

Figure 4.5 Unpacking Back Refractory

Figure 4.8 Removing the Screen Rods

Remove hearth stone by removing three corrugated shipping spacers (Figure 4.9). Lift hearth stone out of fireplace. See Figure 4.10.

Figure 4.9 Shipping Spacers

Figure 4.6 Bending Refractory Shipping Tabs Back Down

Figure 4.10 Lifting Out the Hearth Stone

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Fire Risk Hot glass will cause burnsListing Label Information/Location GrateNumber Table of Contents Listing and Code Approvals Appliance CertificationNot intended for use as a primary heat source Asphyxiation Risk Design and Installation ConsiderationsGetting Started Negative PressureMarginal Location Typical Fireplace System Typical Fireplace SystemTools and Supplies Needed Inspect Fireplace and ComponentsFire Risk Explosion Risk Selecting Fireplace Location Framing and ClearancesClearances to Combustible Materials ClearancesFrame the Fireplace Sidewalls/SurroundsChimney Requirements Construct the ChaseRisk of Smoke Spillage Installation of Fireplace¨ A. Install the Outside Air Kit Fire Risk Sharp Edges Asphyxiation RiskAttic insulation shield Must be used to keep Install the Refractory Secure the FireplacePosition the Fireplace Grate Brackets Grate Bracket Level the Fireplace Place the Protective Metal Hearth StripsChimney Assembly Height of Chimney Components Chimney Offset/Return Using Offsets/ReturnsAssemble the Chimney Sections Install the Ceiling FirestopsPrepare Attic Insulation Shield Install the Attic Insulation ShieldSecure the Chimney Double-check the Chimney AssemblyComplete the Enclosure Chimney TerminationChimney Termination Requirements See Figure Cut Out the Hole in the Roof Install the Roof FlashingInstall the Chimney Air Kit required in Canada Mark the Exit Point of the RoofChase Top Install the Termination CapInstalling an ST1175 or ST475 Square Termination Cap Accessories Gas Log/Lighter ProvisionsGas Code, Ansi Z223.1 Hearth Extension FinishingCAT. # Finishing Material Combustible MaterialNon-Combustible Material Mantel Glass DoorsNFPA211 General Information Operating InstructionsFirescreen Outside AirClear Space Near the Fireplace Flue DamperMoisture GrateWood Fuel FirewoodStarting a Fire Understanding Vent Problems TroubleshootingCan’t get a good fire going. What am I doing wrong? Diagnostics and Problem SolvingDiagnostic Questions Solutionsfireplace burns the wood too fast. What can I do? Firebox Refractory Maintenance and Servicing the FireplaceChimney Inspection/Cleaning Disposal of AshesChimney Fire Maintenance Task ListWhen cleaning glass door CleanReference Materials Fireplace DimensionsCatalog # Description Fireplace ComponentsCatalog # Chimney Components15-1/4 387 mm Catalog # European Copper Caps Available in US only Woodburning Termination Cap Heatilator I80 CAN-US 4013-203 Rev F 04/08 ¨ D. Service PartsI80H Description of Part Serial # CutoffThis page intentionally left blank This page intentionally left blank This page intentionally left blank Limited Warranty Contact Information

I80 specifications

The Heatiator I80 is a cutting-edge fireplace insert designed to provide efficient heating while enhancing the aesthetics of any living space. Combining modern technology with elegant design, the I80 is perfect for homeowners looking to experience the warmth and ambiance of a fire without sacrificing efficiency.

One of the standout features of the Heatiator I80 is its advanced heating technology. With a high-efficiency rating, this insert maximizes heat output while minimizing fuel consumption. The I80 is designed to utilize either wood or gas, offering versatility for users based on their preference and availability. The dual-fuel capability allows for easy adaptation to different conditions, providing comfort and warmth throughout the year.

The I80 incorporates a patented airflow system that improves heat circulation within the home. This innovative system distributes warm air efficiently, ensuring that every corner of the room feels cozy. Additionally, the insert comes with an adjustable fan that can be tailored to suit user preferences, allowing for customized heating levels based on the desired atmosphere.

Another impressive characteristic of the Heatiator I80 is its sleek design. The fireplace insert features a large viewing window, crafted from high-temperature tempered glass, which not only showcases the mesmerizing flames but also complements contemporary interior decor. The minimalist design is available in various finishes, enabling homeowners to choose an option that best fits their style.

Safety is a paramount concern, and the I80 comes equipped with several safety features. It includes a built-in safety shut-off mechanism that engages if the temperature rises beyond safe levels, ensuring peace of mind for users. Moreover, the unit is designed with an outer casing that remains cool to the touch, making it suitable for homes with children and pets.

Installation of the Heatiator I80 is straightforward, thanks to its flexible venting options. Whether retrofitting an existing fireplace or installing a new insert, the adaptability of the I80 accommodates various configurations, allowing for hassle-free integration into any home.

In conclusion, the Heatiator I80 stands out due to its combination of high efficiency, aesthetic appeal, and advanced safety features. With its ability to deliver warmth, ambiance, and design compatibility, it represents an exceptional option for those seeking to enhance their living space while enjoying the comfort of a modern fireplace insert.
Top Page Image Contents