Heatiator I80 owner manual 15-1/4 387 mm

Page 46

Inside Diameter

SL1100 - 11 in. (279mm)

SL400 - 10 in. (254mm)

21 in.

(533 mm) Outside Diameter

13 in. (330 mm)

SL1130/SL430 Offset/Return

Assembled

Diameter: 17 in./432 mm

Height: 24 in./610 mm

AS10 Straight Attic Insulation Shield

13 in.

2 in.

(330 mm)

(51 mm)

JB577 Chimney Joint Band

13 in. (330 mm)

CB576 Chimney Joint Band

A

B17 in. (432 mm)

Ceiling Firestop

Catalog #

A

 

B

FS538

0-deg.

17 in.

 

432 mm

FS540

30-deg.

26 in.

 

660 mm

15-1/4 in.

(387 mm)

29 in.

25-1/4 in.

(737 mm)

(641 mm)

RF570 Roof Flashing

15-1/4in.

(387 mm)

39-7/8 in.

28 in.

(711 mm)

(1013 mm)

 

RF571 Roof Flashing

 

46

Heatilator • I80 CAN-US4013-203 Rev F • 04/08

Image 46
Contents Hot glass will cause burns Fire RiskGrate Listing Label Information/LocationNumber Table of Contents Appliance Certification Listing and Code ApprovalsNot intended for use as a primary heat source Negative Pressure Design and Installation ConsiderationsGetting Started Asphyxiation RiskMarginal Location Typical Fireplace System Typical Fireplace SystemInspect Fireplace and Components Tools and Supplies NeededFire Risk Explosion Risk Framing and Clearances Selecting Fireplace LocationClearances Clearances to Combustible MaterialsSidewalls/Surrounds Frame the FireplaceConstruct the Chase Chimney RequirementsFire Risk Sharp Edges Asphyxiation Risk Installation of Fireplace¨ A. Install the Outside Air Kit Risk of Smoke SpillageAttic insulation shield Must be used to keep Secure the Fireplace Install the RefractoryPosition the Fireplace Grate Brackets Grate Bracket Place the Protective Metal Hearth Strips Level the FireplaceChimney Assembly Height of Chimney Components Using Offsets/Returns Chimney Offset/ReturnInstall the Ceiling Firestops Assemble the Chimney SectionsInstall the Attic Insulation Shield Prepare Attic Insulation ShieldDouble-check the Chimney Assembly Secure the ChimneyChimney Termination Complete the EnclosureChimney Termination Requirements See Figure Mark the Exit Point of the Roof Install the Roof FlashingInstall the Chimney Air Kit required in Canada Cut Out the Hole in the RoofInstall the Termination Cap Chase TopInstalling an ST1175 or ST475 Square Termination Cap Gas Log/Lighter Provisions AccessoriesGas Code, Ansi Z223.1 Finishing Hearth ExtensionCAT. # Combustible Material Finishing MaterialNon-Combustible Material Glass Doors MantelNFPA211 Operating Instructions General InformationFlue Damper Outside AirClear Space Near the Fireplace FirescreenFirewood GrateWood Fuel MoistureStarting a Fire Troubleshooting Understanding Vent ProblemsSolutions Diagnostics and Problem SolvingDiagnostic Questions Can’t get a good fire going. What am I doing wrong?fireplace burns the wood too fast. What can I do? Disposal of Ashes Maintenance and Servicing the FireplaceChimney Inspection/Cleaning Firebox RefractoryClean Maintenance Task ListWhen cleaning glass door Chimney FireFireplace Dimensions Reference MaterialsFireplace Components Catalog # DescriptionChimney Components Catalog #15-1/4 387 mm Catalog # European Copper Caps Available in US only Woodburning Termination Cap ¨ D. Service Parts Heatilator I80 CAN-US 4013-203 Rev F 04/08Description of Part Serial # Cutoff I80HThis page intentionally left blank This page intentionally left blank This page intentionally left blank Limited Warranty Contact Information

I80 specifications

The Heatiator I80 is a cutting-edge fireplace insert designed to provide efficient heating while enhancing the aesthetics of any living space. Combining modern technology with elegant design, the I80 is perfect for homeowners looking to experience the warmth and ambiance of a fire without sacrificing efficiency.

One of the standout features of the Heatiator I80 is its advanced heating technology. With a high-efficiency rating, this insert maximizes heat output while minimizing fuel consumption. The I80 is designed to utilize either wood or gas, offering versatility for users based on their preference and availability. The dual-fuel capability allows for easy adaptation to different conditions, providing comfort and warmth throughout the year.

The I80 incorporates a patented airflow system that improves heat circulation within the home. This innovative system distributes warm air efficiently, ensuring that every corner of the room feels cozy. Additionally, the insert comes with an adjustable fan that can be tailored to suit user preferences, allowing for customized heating levels based on the desired atmosphere.

Another impressive characteristic of the Heatiator I80 is its sleek design. The fireplace insert features a large viewing window, crafted from high-temperature tempered glass, which not only showcases the mesmerizing flames but also complements contemporary interior decor. The minimalist design is available in various finishes, enabling homeowners to choose an option that best fits their style.

Safety is a paramount concern, and the I80 comes equipped with several safety features. It includes a built-in safety shut-off mechanism that engages if the temperature rises beyond safe levels, ensuring peace of mind for users. Moreover, the unit is designed with an outer casing that remains cool to the touch, making it suitable for homes with children and pets.

Installation of the Heatiator I80 is straightforward, thanks to its flexible venting options. Whether retrofitting an existing fireplace or installing a new insert, the adaptability of the I80 accommodates various configurations, allowing for hassle-free integration into any home.

In conclusion, the Heatiator I80 stands out due to its combination of high efficiency, aesthetic appeal, and advanced safety features. With its ability to deliver warmth, ambiance, and design compatibility, it represents an exceptional option for those seeking to enhance their living space while enjoying the comfort of a modern fireplace insert.