Heatiator I80 owner manual Typical Fireplace System

Page 7

C. Typical Fireplace System

The Heatilator fireplace system consists of the following:

•Fireplace/integral grate/refractory/outside air system

•Refractory

•Chimney termination cap

•Chimney system (SL1100 series pipe is NOT approved for Canada)

•Hearth extension

Optional components include:

•Glass doors

•Chimney air kit (required in Canada)

•SLA10 - 11-10 in./279-254mm adaptor (required in Canada)

Additional lateral support for chimney above roof (or enclosed in chase) if needed

Non-combustible

roof flashing maintains minimum clearance around chimney

Support straps on rafter supports chimney (not shown)

Ceiling firestop on floor of attic

Chimney system

Combustible framing/header on top of V-shaped standoffs (spacers)

Outside combustion air

Protective metal hearth strip(s)

Termination cap

Storm Collar

Chimney penetrates roof preferably without affecting roof rafters

Offset/Return (with hanger straps)

Attic insulation shield (not shown) must be used here to keep insulation away from chimney if attic is insulated

Framing headed off in ceiling joists

Enclosed space above and around fireplace

Mantel and surround

Decorative facing and trim

Hearth extension

Factory-built fireplace

Figure 2.2 Typical Fireplace System

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Fire Risk Hot glass will cause burnsGrate Listing Label Information/LocationNumber Table of Contents Appliance Certification Listing and Code ApprovalsNot intended for use as a primary heat source Asphyxiation Risk Design and Installation ConsiderationsGetting Started Negative PressureMarginal Location Typical Fireplace System Typical Fireplace SystemInspect Fireplace and Components Tools and Supplies NeededFire Risk Explosion Risk Selecting Fireplace Location Framing and ClearancesClearances to Combustible Materials ClearancesFrame the Fireplace Sidewalls/SurroundsChimney Requirements Construct the ChaseRisk of Smoke Spillage Installation of Fireplace¨ A. Install the Outside Air Kit Fire Risk Sharp Edges Asphyxiation RiskAttic insulation shield Must be used to keep Secure the Fireplace Install the RefractoryPosition the Fireplace Grate Brackets Grate Bracket Level the Fireplace Place the Protective Metal Hearth StripsChimney Assembly Height of Chimney Components Chimney Offset/Return Using Offsets/ReturnsAssemble the Chimney Sections Install the Ceiling FirestopsPrepare Attic Insulation Shield Install the Attic Insulation ShieldSecure the Chimney Double-check the Chimney AssemblyChimney Termination Complete the EnclosureChimney Termination Requirements See Figure Cut Out the Hole in the Roof Install the Roof FlashingInstall the Chimney Air Kit required in Canada Mark the Exit Point of the RoofChase Top Install the Termination CapInstalling an ST1175 or ST475 Square Termination Cap Gas Log/Lighter Provisions AccessoriesGas Code, Ansi Z223.1 Hearth Extension FinishingCAT. # Combustible Material Finishing MaterialNon-Combustible Material Glass Doors MantelNFPA211 General Information Operating InstructionsFirescreen Outside AirClear Space Near the Fireplace Flue DamperMoisture GrateWood Fuel FirewoodStarting a Fire Understanding Vent Problems TroubleshootingCan’t get a good fire going. What am I doing wrong? Diagnostics and Problem SolvingDiagnostic Questions Solutionsfireplace burns the wood too fast. What can I do? Firebox Refractory Maintenance and Servicing the FireplaceChimney Inspection/Cleaning Disposal of AshesChimney Fire Maintenance Task ListWhen cleaning glass door CleanReference Materials Fireplace DimensionsCatalog # Description Fireplace ComponentsCatalog # Chimney Components15-1/4 387 mm Catalog # European Copper Caps Available in US only Woodburning Termination Cap Heatilator I80 CAN-US 4013-203 Rev F 04/08 ¨ D. Service PartsI80H Description of Part Serial # CutoffThis page intentionally left blank This page intentionally left blank This page intentionally left blank Limited Warranty Contact Information

I80 specifications

The Heatiator I80 is a cutting-edge fireplace insert designed to provide efficient heating while enhancing the aesthetics of any living space. Combining modern technology with elegant design, the I80 is perfect for homeowners looking to experience the warmth and ambiance of a fire without sacrificing efficiency.

One of the standout features of the Heatiator I80 is its advanced heating technology. With a high-efficiency rating, this insert maximizes heat output while minimizing fuel consumption. The I80 is designed to utilize either wood or gas, offering versatility for users based on their preference and availability. The dual-fuel capability allows for easy adaptation to different conditions, providing comfort and warmth throughout the year.

The I80 incorporates a patented airflow system that improves heat circulation within the home. This innovative system distributes warm air efficiently, ensuring that every corner of the room feels cozy. Additionally, the insert comes with an adjustable fan that can be tailored to suit user preferences, allowing for customized heating levels based on the desired atmosphere.

Another impressive characteristic of the Heatiator I80 is its sleek design. The fireplace insert features a large viewing window, crafted from high-temperature tempered glass, which not only showcases the mesmerizing flames but also complements contemporary interior decor. The minimalist design is available in various finishes, enabling homeowners to choose an option that best fits their style.

Safety is a paramount concern, and the I80 comes equipped with several safety features. It includes a built-in safety shut-off mechanism that engages if the temperature rises beyond safe levels, ensuring peace of mind for users. Moreover, the unit is designed with an outer casing that remains cool to the touch, making it suitable for homes with children and pets.

Installation of the Heatiator I80 is straightforward, thanks to its flexible venting options. Whether retrofitting an existing fireplace or installing a new insert, the adaptability of the I80 accommodates various configurations, allowing for hassle-free integration into any home.

In conclusion, the Heatiator I80 stands out due to its combination of high efficiency, aesthetic appeal, and advanced safety features. With its ability to deliver warmth, ambiance, and design compatibility, it represents an exceptional option for those seeking to enhance their living space while enjoying the comfort of a modern fireplace insert.
Top Page Image Contents