Heatiator I80 owner manual Starting a Fire

Page 37

I. Starting a Fire

Check the flue damper to be certain it is in the full open po- sition. Place crumpled or twisted paper under the fireplace grate. Loosely arrange kindling or small pieces of wood to form a layer above the paper.

The fires must be built on the fireplace grate, without danger of the burning fuel falling out of the fireplace opening.

Light the paper and add small pieces of wood until a hot bed of embers has been established.

After establishing the fire bed, and the small firewood is burn- ing briskly, add a minimum of three average sized pieces of split firewood, place the wood in such a manner to allow combustion air and flames between them.

Note: When first lighting your fireplace, it may be neces- sary to pre-warm the flue to establish a draft. This is done by holding a rolled up piece of burning newspaper under the flue damper for a few moments. This will help reduce smoke spillage during start-up.

Note: The first three or four fires should be of moderate size to allow the oils and binders to be burned from the fireplace and the refractory and paint to cure. You may notice an industrial odor the first few fires. This is consid- ered normal.

CAUTION

Odors and vapors released during initial operation.

•Curing of high temperature paint.

•Open windows for air circulation.

Odors may be irritating to sensitive individuals.

WARNING

Fire Risk

Keep combustible materials, gasoline and other flammable vapors and liquids clear of fireplace.

•Do NOT store flammable materials close to the fireplace.

•Do NOT use gasoline, lantern fuel, kerosene, charcoal lighter fluid or similar liquids to start or “freshen up” a fire in this fireplace.

•Keep all such liquids well away from the fireplace while it is in use.

Combustible materials may ignite.

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Fire Risk Hot glass will cause burnsGrate Listing Label Information/LocationNumber Table of Contents Appliance Certification Listing and Code ApprovalsNot intended for use as a primary heat source Getting Started Design and Installation ConsiderationsNegative Pressure Asphyxiation RiskMarginal Location Typical Fireplace System Typical Fireplace SystemInspect Fireplace and Components Tools and Supplies NeededFire Risk Explosion Risk Selecting Fireplace Location Framing and ClearancesClearances to Combustible Materials ClearancesFrame the Fireplace Sidewalls/SurroundsChimney Requirements Construct the Chase¨ A. Install the Outside Air Kit Installation of FireplaceFire Risk Sharp Edges Asphyxiation Risk Risk of Smoke SpillageAttic insulation shield Must be used to keep Secure the Fireplace Install the RefractoryPosition the Fireplace Grate Brackets Grate Bracket Level the Fireplace Place the Protective Metal Hearth StripsChimney Assembly Height of Chimney Components Chimney Offset/Return Using Offsets/ReturnsAssemble the Chimney Sections Install the Ceiling FirestopsPrepare Attic Insulation Shield Install the Attic Insulation ShieldSecure the Chimney Double-check the Chimney AssemblyChimney Termination Complete the EnclosureChimney Termination Requirements See Figure Install the Chimney Air Kit required in Canada Install the Roof FlashingMark the Exit Point of the Roof Cut Out the Hole in the RoofChase Top Install the Termination CapInstalling an ST1175 or ST475 Square Termination Cap Gas Log/Lighter Provisions AccessoriesGas Code, Ansi Z223.1 Hearth Extension FinishingCAT. # Combustible Material Finishing MaterialNon-Combustible Material Glass Doors MantelNFPA211 General Information Operating InstructionsClear Space Near the Fireplace Outside AirFlue Damper FirescreenWood Fuel GrateFirewood MoistureStarting a Fire Understanding Vent Problems TroubleshootingDiagnostic Questions Diagnostics and Problem SolvingSolutions Can’t get a good fire going. What am I doing wrong?fireplace burns the wood too fast. What can I do? Chimney Inspection/Cleaning Maintenance and Servicing the FireplaceDisposal of Ashes Firebox RefractoryWhen cleaning glass door Maintenance Task ListClean Chimney FireReference Materials Fireplace DimensionsCatalog # Description Fireplace ComponentsCatalog # Chimney Components15-1/4 387 mm Catalog # European Copper Caps Available in US only Woodburning Termination Cap Heatilator I80 CAN-US 4013-203 Rev F 04/08 ¨ D. Service PartsI80H Description of Part Serial # CutoffThis page intentionally left blank This page intentionally left blank This page intentionally left blank Limited Warranty Contact Information

I80 specifications

The Heatiator I80 is a cutting-edge fireplace insert designed to provide efficient heating while enhancing the aesthetics of any living space. Combining modern technology with elegant design, the I80 is perfect for homeowners looking to experience the warmth and ambiance of a fire without sacrificing efficiency.

One of the standout features of the Heatiator I80 is its advanced heating technology. With a high-efficiency rating, this insert maximizes heat output while minimizing fuel consumption. The I80 is designed to utilize either wood or gas, offering versatility for users based on their preference and availability. The dual-fuel capability allows for easy adaptation to different conditions, providing comfort and warmth throughout the year.

The I80 incorporates a patented airflow system that improves heat circulation within the home. This innovative system distributes warm air efficiently, ensuring that every corner of the room feels cozy. Additionally, the insert comes with an adjustable fan that can be tailored to suit user preferences, allowing for customized heating levels based on the desired atmosphere.

Another impressive characteristic of the Heatiator I80 is its sleek design. The fireplace insert features a large viewing window, crafted from high-temperature tempered glass, which not only showcases the mesmerizing flames but also complements contemporary interior decor. The minimalist design is available in various finishes, enabling homeowners to choose an option that best fits their style.

Safety is a paramount concern, and the I80 comes equipped with several safety features. It includes a built-in safety shut-off mechanism that engages if the temperature rises beyond safe levels, ensuring peace of mind for users. Moreover, the unit is designed with an outer casing that remains cool to the touch, making it suitable for homes with children and pets.

Installation of the Heatiator I80 is straightforward, thanks to its flexible venting options. Whether retrofitting an existing fireplace or installing a new insert, the adaptability of the I80 accommodates various configurations, allowing for hassle-free integration into any home.

In conclusion, the Heatiator I80 stands out due to its combination of high efficiency, aesthetic appeal, and advanced safety features. With its ability to deliver warmth, ambiance, and design compatibility, it represents an exceptional option for those seeking to enhance their living space while enjoying the comfort of a modern fireplace insert.
Top Page Image Contents