Heatiator I80 owner manual Height of Chimney Components

Page 20

A. Chimney Requirements

Vertical distances are measured from the base of the fire- place as shown in Figure 5.2.

 

ft

m

• Minimum overall straight height

18

5.5

• Minimum height with offset/return

18.5

5.6

• Maximum height

90

27.4

• Maximum chimney length between an offset and

20

6

return

 

 

• Maximum distance between chimney stabilizers

35

10.7

• Double offset/return minimum height

24

7.3

• Maximum unsupported chimney length between the

6

1.8

offset and return

 

 

• Maximum straight unsupported chimney height

35

10.7

above the fireplace

 

 

• Maximum unsupported chimney above roof

6

1.8

To determine the chimney components needed to complete your particular installation, follow the steps below:

•Determine the total vertical height of the fireplace installation. This dimension is measured from the base of the fireplace assembly to the point where the smoke exits the termination cap.

•Subtract the effective height of the fireplace assembly from the overall height of the fireplace installation (measured from the base of the fireplace to the bottom of the termination cap).

•Refer to Table 5.1 to determine what components must be selected to complete the fireplace installation.

•Determine the number of ceiling firestops, stabilizers, roof flashing, etc. required to complete the fireplace installation.

Note: A maximum of two pairs of offsets and returns may be used.

WARNING

Fire Risk

•Must maintain 2 in. (51 mm) air clearance to insulation and other combustible materials.

Table 5.1

HEIGHT OF CHIMNEY

 

 

 

COMPONENTS

 

in.

mm

US

 

Canada

 

 

Chimney Stabilizer

 

 

 

SL11

 

SL4

4-3/4

121

 

 

 

 

 

Ceiling Firestops

 

 

 

FS538

 

FS538

0

0

 

 

 

 

 

FS540

 

FS540

0

0

Offsets/Returns

 

 

 

SL1130

 

SL430

14-1/2

368

 

 

 

 

 

6 ft (1.8 m) max. unsupported run

20 ft (6 m) max. pipe between an offset & return

Ceiling Firestop

11-10 in./279-254mm adaptor required in Canada

55-1/2 in.

(1410 mm)

Effective Height

(bottom of fireplace

to top of starter collar)

6 ft (1.8 m) max. unsupported chimney above roof

35 ft (10.7 m) max. straight unsupported chimney height

18.5ft (5.6 m) min. height/single offset-return 24 ft. (7.3 m) min. height/double offset-return

90 ft (27.4 m) max. height

Roof Flashing

 

 

 

RF570

 

RF570

0

0

 

 

 

 

 

RF571

 

RF571

0

0

Chimney Sections*

 

 

 

SL1106

 

SL406

4-3/4

121

SL1112

 

SL412

10-3/4

273

SL1118

 

SL418

16-3/4

425

 

 

 

 

 

SL1136

 

SL436

34-3/4

883

SL1148

 

SL448

46-3/4

1187

 

 

 

 

 

n/a

 

SLA10

16-3/4

425

* Dimensions reflect effective height.

Figure 5.2 Chimney Requirements

CAUTION

•Do NOT connect this fireplace to a chimney flue servicing another appliance.

•Do NOT connect to any air distribution duct or system.

20

Heatilator • I80 CAN-US • 4013-203 Rev F • 04/08

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Hot glass will cause burns Fire RiskNumber Listing Label Information/LocationGrate Table of Contents Not intended for use as a primary heat source Listing and Code ApprovalsAppliance Certification Design and Installation Considerations Getting StartedNegative Pressure Asphyxiation RiskMarginal Location Typical Fireplace System Typical Fireplace SystemFire Risk Explosion Risk Tools and Supplies NeededInspect Fireplace and Components Framing and Clearances Selecting Fireplace LocationClearances Clearances to Combustible MaterialsSidewalls/Surrounds Frame the FireplaceConstruct the Chase Chimney RequirementsInstallation of Fireplace ¨ A. Install the Outside Air KitFire Risk Sharp Edges Asphyxiation Risk Risk of Smoke SpillageAttic insulation shield Must be used to keep Position the Fireplace Install the RefractorySecure the Fireplace Grate Brackets Grate Bracket Place the Protective Metal Hearth Strips Level the FireplaceChimney Assembly Height of Chimney Components Using Offsets/Returns Chimney Offset/ReturnInstall the Ceiling Firestops Assemble the Chimney SectionsInstall the Attic Insulation Shield Prepare Attic Insulation ShieldDouble-check the Chimney Assembly Secure the ChimneyChimney Termination Requirements See Figure Complete the EnclosureChimney Termination Install the Roof Flashing Install the Chimney Air Kit required in CanadaMark the Exit Point of the Roof Cut Out the Hole in the RoofInstall the Termination Cap Chase TopInstalling an ST1175 or ST475 Square Termination Cap Gas Code, Ansi Z223.1 AccessoriesGas Log/Lighter Provisions Finishing Hearth ExtensionCAT. # Non-Combustible Material Finishing MaterialCombustible Material NFPA211 MantelGlass Doors Operating Instructions General InformationOutside Air Clear Space Near the FireplaceFlue Damper FirescreenGrate Wood FuelFirewood MoistureStarting a Fire Troubleshooting Understanding Vent ProblemsDiagnostics and Problem Solving Diagnostic QuestionsSolutions Can’t get a good fire going. What am I doing wrong?fireplace burns the wood too fast. What can I do? Maintenance and Servicing the Fireplace Chimney Inspection/CleaningDisposal of Ashes Firebox RefractoryMaintenance Task List When cleaning glass doorClean Chimney FireFireplace Dimensions Reference MaterialsFireplace Components Catalog # DescriptionChimney Components Catalog #15-1/4 387 mm Catalog # European Copper Caps Available in US only Woodburning Termination Cap ¨ D. Service Parts Heatilator I80 CAN-US 4013-203 Rev F 04/08Description of Part Serial # Cutoff I80HThis page intentionally left blank This page intentionally left blank This page intentionally left blank Limited Warranty Contact Information

I80 specifications

The Heatiator I80 is a cutting-edge fireplace insert designed to provide efficient heating while enhancing the aesthetics of any living space. Combining modern technology with elegant design, the I80 is perfect for homeowners looking to experience the warmth and ambiance of a fire without sacrificing efficiency.

One of the standout features of the Heatiator I80 is its advanced heating technology. With a high-efficiency rating, this insert maximizes heat output while minimizing fuel consumption. The I80 is designed to utilize either wood or gas, offering versatility for users based on their preference and availability. The dual-fuel capability allows for easy adaptation to different conditions, providing comfort and warmth throughout the year.

The I80 incorporates a patented airflow system that improves heat circulation within the home. This innovative system distributes warm air efficiently, ensuring that every corner of the room feels cozy. Additionally, the insert comes with an adjustable fan that can be tailored to suit user preferences, allowing for customized heating levels based on the desired atmosphere.

Another impressive characteristic of the Heatiator I80 is its sleek design. The fireplace insert features a large viewing window, crafted from high-temperature tempered glass, which not only showcases the mesmerizing flames but also complements contemporary interior decor. The minimalist design is available in various finishes, enabling homeowners to choose an option that best fits their style.

Safety is a paramount concern, and the I80 comes equipped with several safety features. It includes a built-in safety shut-off mechanism that engages if the temperature rises beyond safe levels, ensuring peace of mind for users. Moreover, the unit is designed with an outer casing that remains cool to the touch, making it suitable for homes with children and pets.

Installation of the Heatiator I80 is straightforward, thanks to its flexible venting options. Whether retrofitting an existing fireplace or installing a new insert, the adaptability of the I80 accommodates various configurations, allowing for hassle-free integration into any home.

In conclusion, the Heatiator I80 stands out due to its combination of high efficiency, aesthetic appeal, and advanced safety features. With its ability to deliver warmth, ambiance, and design compatibility, it represents an exceptional option for those seeking to enhance their living space while enjoying the comfort of a modern fireplace insert.
Top Page Image Contents