Desa RLP100 owner manual Service Procedures, Motor, With heater on its side, remove base tray

Page 8

SERVICE PROCEDURES

WARNING: Never service heater while it is plugged in, connected to propane supply, operating or hot. Severe burns and electrical shock can occur.

MOTOR

1.With heater on its side, remove base tray.

2.Access ground screw through underside of heater base. Remove ground screw. Disconnect the green motor wire and the green power cord wire from underside of shell (see Figure 5).

3.Remove black and white motor wires from terminal board (see Figure 5).

4.Carefully push motor wires through hole in bottom of shell.

5.Remove screws holding motor mount to shell. Use nut-driver (see Figure 6).

6.Carefully pull motor and fan out of shell. IMPORTANT: Be careful not to damage fan. Do not set motor and fan down with the weight resting on fan. This could damage fan pitch.

7.Use hex wrench to loosen setscrew which holds fan to motor shaft.

8.Remove fan. Be careful not to damage the fan blade pitch.

9.Use nut driver to remove two nuts that attach motor to motor mount.

10.Discard old motor.

11.Attach motor to motor mount with two nuts. Tighten nuts firmly.

12.Replace fan on motor shaft. Make sure set screw contacts flat surface on motor shaft.

13.Tighten set screw firmly (40-50 inch-pounds [46.08-57.60 kilogram-centimeters]).

 

Transformer

Ground Screw

Green Lead

Motor

Power

Green

Cord

Lead

Green

 

Lead

14.Carefully route motor wires through hole in shell (see Figure 7). Place motor, motor mount and fan guard into rear of heater shell.

15.Insert screws through heater shell and into motor mount. Tighten screws firmly.

16.Turn heater on its side to access opening in bottom of base. Connect green wires from motor, transformer and power cord to heater shell using ground nut (see Figure 5).

17.Attach black and white wires to terminal board (see Wiring Diagram, page 11, for correct locations) .

18.Replace base tray.

Motor

Mount

Screw

Fan

Guard

Motor

Mount

Hole in Shell for Wires

Figure 6 - Removing Motor, Motor Mount and Fan Guard from Heater

Hole in

Shell for

Wires

Figure 7 - Replacing Motor, Motor Mount and Fan Guard into Heater

Terminal

Board

Figure 5 - Location of Ground Screw

8

www.desatech.com

111710-01B

Image 8
Contents Table of Contents General Hazard WarningSafety Information Product Identification UnpackingInstallation Amount of propane gas in tanks Temperature of tanksPropane Supply Provide propane supply system see Propane Supply aboveVentilation OperationTo Start Heater To Stop HeaterMaintenance Have heater inspected yearly by a qualified service agencyClean fan blades each season or as needed see Fan, StorageTroubleshooting Observed Fault Possible Cause RemedyWith heater on its side, remove base tray Service ProceduresMotor FAN Spark TransformerIgnitor Removing Ignitor Mounting Screw and IgnitorWiring Diagram Specifications Output Rating Btu/HrPsi 65.98 Kpa Heater 26.25 x 9 xAccessories Technical ServiceReplacement Parts Illustrated Parts Breakdown Parts List 100,000 Btu/Hr Models RM100LP and RLP100Warranty and Repair Service Keep this WarrantyLimited Warranty Warranty ServiceAdvertencia General DE Peligro ETC., Comuníquese CON EL Fabricante Tabla DE ContenidoInformación DE Seguridad Identificación DEL ProductoDesempaque Teoría DEL FuncionamientoInstalación Debe aprovisionar el usuarioDe 45 kg 100 lb que se necesitan para hacer Funcionar este calentadorVentilación Para Encender EL CalentadorCierre la válvula del suministro de propano Adicional si se utilizan más calentadores. FuncionamientoAlmacenamiento MantenimientoPara Apagar EL Calentador Desconecte el calentadorSolución DE Problemas El calentador se apaga 1. Es posible que el suministro de Propano no sea el adecuadoApague el calentador Flujo restringido del aireProcedimientos DE Servicio Vuelva a colocar la charola de la baseVentilador Transformador DE ChispaSeque completamente el ventilador Desmonte la charola de la basePruebe a ver si se produce una chispa Extraiga el ignitor de la cabeza posteriorConecte el cable del ignitor Modelo DE 100.000 BTU/H Diagrama DEL CableadoEspecificaciones Servicio Técnico Piezas DE RepuestoAccesorios Piezas CON GarantíaClasificación Ilustrada DE Piezas Modelos DE 100.000 BTU/H RM100LPLista DE Piezas 100.000 BTU/H Modelos RM100LP Y RLP100Garantía Y Servicio DE Reparación Guarde Esta GarantíaGarantía Limitada Servicio DE Garantía

RLP100 specifications

Desa RLP100 is an innovative technological marvel designed for both indoor and outdoor applications. As a compact and versatile solution, it combines cutting-edge features and reliable performance in one package. The RLP100 is designed with user convenience and efficiency in mind, making it an ideal choice for various sectors, including residential, commercial, and industrial environments.

One of the standout features of the Desa RLP100 is its energy efficiency. Utilizing advanced energy-saving technologies, this device optimally manages power consumption while maintaining high performance levels. This not only reduces operational costs for users but also contributes positively to environmental conservation.

The RLP100 is equipped with a state-of-the-art control system that allows for seamless integration with modern smart home technologies. Users can easily manage settings through a mobile application or centralized control units, providing remote access and enhancing user experience. The system supports voice commands, making it compatible with popular virtual assistants, thus catering to a growing demand for smart living solutions.

Safety is a top priority with the RLP100, which comes with an array of built-in safety features. These include automatic shut-off mechanisms, temperature regulation, and fault detection systems that alert users to potential issues. Such robust safety measures not only protect users but also enhance the longevity of the device.

The Desa RLP100 is designed for adaptability, featuring adjustable settings that can be customized to meet the specific needs of different environments. Whether it’s heating, cooling, or air purification, the RLP100 delivers results that can be tailored to user preferences. Its compact design ensures that it can fit into small or constrained spaces without compromising performance.

Moreover, the RLP100 employs innovative filtration technologies that ensure optimal air quality. With multi-layer filtration systems, it effectively removes allergens, dust, and other pollutants, making it a significant asset for health-conscious users. This feature is particularly beneficial in urban areas where air quality can be a concern.

In summary, the Desa RLP100 embodies modern technology with its impressive features, user-friendly design, and a strong focus on safety and efficiency. Its ability to adapt to varying needs, coupled with its smart integration capabilities, positions it as a leader in the market, appealing to anyone seeking a reliable and advanced solution for enhancing their living or working environment.