Desa CCL3924N, CRL3124N, CRL2718N Installing Logs, Pressure Testing Heater Gas Connections

Page 13

INSTALLATION

Checking Gas Connections (Cont.) Installing Logs

13

INSTALLATION

Continued

Pressure Testing Heater Gas Connections

1.Open equipment shutoff valve (see Figure 16, page 12).

2.Open main gas valve located on or near gas meter.

3.Make sure control knob of heater is in the OFF position.

4.Check all joints from equipment shutoff valve to control valve (see Figure 17). Apply a noncorrosive leak detection fluid to gas joints. Bubbles forming show a leak.

5.Correct all leaks at once.

6.Light heater (see Operating Heater, pages 17 and 18 [manu- ally-controlled models] or pages 18 through 20 [thermostati- cally-controlled models]). Check all other internal joints for leaks.

7.Turn off heater (see To Turn Off Gas to Appliance, page 18 [manually-controlled models] or page 19 [thermostatically-con- trolled models]).

1.

Locate pins on the bottom of back log (#1). Slide these pins into

 

the holes in the grate base behind the burner (see Figure 18).

2.

Place the base of the middle log (#2) in the U-shaped slots of

 

the grate base in front of the back log. The cutout on the right

 

of the middle log should fit over the burner (see Figure 19).

 

Make sure the front of the middle log is resting on the tabs of

 

the grate base and the cutout area is centered over the burner

 

“U” bend.

3.

Locate the recesses on the back of the front log (#3). Fit these

 

recesses between the posts of the grate base (see Figure 20).

4.

Locate the notches in the bottom of the crossover log (#4).

 

Place the crossover log on top of the middle log and front log.

 

Make sure the notches of the crossover log lines up with rectan-

 

gular knobs on top of the middle and front logs (see Figure 21).

5.

Place lava rock around base of heater if desired. Do not put

Equipment Shutoff Valve

Gas Meter

Thermostat Gas Valve or

Control Valve Location

lava rock on logs on burner.

Middle Log (#2)

 

Back

Pin

Log (#1)

 

 

Cutout

Hole in

 

Grate

Tab

Base

 

Figure 17 - Checking Gas Joints

INSTALLING LOGS

CAUTION: After installation and periodically there- after, check to ensure that no flame comes in contact with any log. With the heater set to high, check to see if flames contact any log. If so, reposition logs ac- cording to the log installation instructions in this manual. Flames contacting logs will create soot.

Dual Burner Smoky Mountain Oak Models

WARNING: Failure to position the parts in accor- dance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury.

Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with heater.

 

Burner

 

Burner

U-Shaped Slot

“U” Bend

 

 

 

Figure 18 - Installing Back Log

Figure 19 - Installing Middle Log

(#1)

(#2)

 

Front Log (#3)

Notches

Crossover

 

Log (#1)

 

 

Recess

 

 

Post

Rectangular

 

Knobs

Figure 20 - Installing Front Log

Figure 21 - Installing

(#3)

Crossover Log (#4)

For morevisit www..com

107123-01E

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Unvented VENT-FREE Natural GAS LOG Heaters OWNER’S Operation Installation ManualBiltmore Split OAK, Seasonal OAK, Smoky Mountain OAK Logs What to do if YOU Smell GASSafety Information Table of ContentsProduct Identification Unpacking Product FeaturesLocal Codes AIR for Combustion and VentilationConfined and Unconfined Space Determining FRESH-AIR Flow for Heater LocationDetermining if You Have a Confined or Unconfined Space Ventilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Installation InstallationCheck GAS Type Minimum Firebox Size Log Front Rear Height Depth WidthMinimum Noncombustible Material Clearances If Not Using MantelMantel Clearances Determining Minimum Mantel Clearance When Using a HoodFloor Clearances Determining Minimum Mantel ClearanceInstalling Heater Base Assembly Installing Damper Clamp Accessory for Vented OperationInstallation Items Needed Area of Various Standard Round FluesAttaching Flexible Gas Hose to Heater Gas Regulator Connecting to GAS SupplyChecking GAS Connections Pressure Testing Gas Supply Piping systemPressure Testing Heater Gas Connections Installing LogsDual Burner Smoky Mountain Oak Models Dual Burner Biltmore Split Oak Models Dual Burner Premium Aged Split Oak ModelsInstalling Rear Log Single Burner Seasonal Oak Models Installing Crossover LogOperating Heater For Your Safety Read Before LightingLighting Instructions Variable Control Operation Manual Lighting ProcedureTo Turn OFF GAS to Appliance Shutting Off HeaterIgnitor Button Inspecting Burners Cleaning and MaintenanceLogs SpecificationsModel Models ModelObserved Problem Possible Cause Remedy TroubleshootingMaintenance, Gas leak. See Warning statement at top TopFor Masonry and Factory-built Metal Fireplace Optional Positioning of Thermostat Sensing BulbBreakdown Illustrated PartsDescription QTY Parts ListCGD3018NT CGD3924NT CGD3930NT Illustrated Parts BreakdownCGD3018NT CGD3924NT CGD3930NT Thermostatically-Controlled Biltmore Split Oak Model CCL3018NTCCL3018NT CCL3924NT, CCL3930NTA CCL3924NT CCL3930NTA Variable Manually-Controlled Seasonal Oak Models CRL2718N CRL3124N Variable Manually-Controlled Mountain Oak ModelsService Hints Replacement PartsTechnical Service AccessoriesOwners Registration Form Postage Required Parts Central Warranty Information
Top Page Image Contents