Desa CCL3924NR Installing Wireless Remote Control Accessory, Installing Logs CGD3924NRA

Page 13

OWNER’S MANUAL

INSTALLATION

Continued

INSTALLING WIRELESS REMOTE CONTROL ACCESSORY

Two 9-volt alkaline batteries (not included) are required to operate this heater with the wireless hand-held remote control set. One battery must be installed in the receiver and one in the hand-held remote control unit. Note: Only use alkaline batteries.

Remote

Control

Unit

Figure 21 - Installing Battery in Hand-Held Remote Control Unit (CGHRCTA Series)

Back Log (#1)

Peg

Hole in

Grate Base

Installing 9-Volt Battery in Receiver

1.Locate back of receiver under front burner of heater.

2.Locate the battery clip mounted on the back of the receiver.

3.Slide a 9-volt battery through the clip.

4.Attach the terminal wires to the battery.

INSTALLING LOGS (CGD3924NRA)

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury.

Burner

Figure 22 - Installing Back Log (#1)

Middle Log (#2)

Tab

Receiver

Battery Clip

9-Volt Battery

Terminal Wires

CAUTION: After installation and periodically thereafter, check to ensure that no flame comes in contact with any log. With the heater set to HIGH, check to see if flames contact any log. If so, reposition logs according to the log installation instructions in this

Burner

Cutout

Figure 19 - Installing Receiver on the Back of the Base

Installing 9-Volt Battery (Not

Included) in Hand-Held Remote

Control Unit

1.Remove battery cover on back of re- mote control unit.

2.Attach terminal wires to the battery. Place battery into the battery housing.

3.Replace battery cover onto remote con- trol unit.

manual. Flames contacting logs will create soot.

Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with heater.

1. Locate pegs on the bottom of back log (#1).

Slide these pegs into the holes in the grate

base behind the burner (see Figure 22).

2. Place the base of the middle log (#2) in

“U” Bend

U-Shaped

Slot

Figure 23 - Installing Middle Log (#2)

Front Log (#3)

Recess

Terminal

Wires

9-Volt Battery

Battery Cover

Remote

Control

Unit

Battery Housing

the U-shaped slots of the grate base in

front of the back log. The cutout on the

right of the middle log should fit over the

burner (see Figure 23). Make sure the

front of the middle log is resting on the

tabs of the grate base and the cutout area

is centered over the burner “U” bend.

3. Locate the recesses on the back of the

front log (#3). Fit these recesses between

Post

Post

Figure 24 - Installing Front Log (#3)

Figure 20 - Installing Battery in Hand- Held Remote Control Unit

the posts of the grate base (see Figure 24).

Continued

107553

13

For more information, visit www.desatech.com

Page 12 Page 14
Image 13
Page 12 Page 14
Contents What to do if YOU Smell GAS Remote ReadyUnvented Natural GAS LOG Heater Safety Information Product Features Safety InformationLocal Codes UnpackingAIR for Combustion and Ventilation Unvented Natural GAS LOG Heater Remote Control AccessoriesProviding Adequate Ventilation Unusually Tight ConstructionDetermining FRESH-AIR Flow for Heater Location AIR for Combustion VentilationDetermining if You Have a Confined or Unconfined Space Ventilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Check GAS Type InstallationLOG Sizing Requirements Minimum Fireplace Clearance to Combustible MaterialsMinimum Noncombustible Material Clearances Unvented Natural GAS LOG Heater InstallationMantel Clearances Determining Minimum Mantel Clearances When Using a HoodFloor Clearances Determining Minimum Mantel ClearancesInstalling Heater Base Assembly Installing Damper Clamp Accessory for Vented OperationInstallation Items Needed Attaching Flexible Gas Hose to Heater Connecting to GAS SupplyPressure Testing gas Supply Piping system Installing Remote Receiver UnitPressure Testing Heater Gas Connections Checking GAS ConnectionsInstalling Logs CGD3924NRA Installing Wireless Remote Control AccessoryInstalling 9-Volt Battery in Receiver Installing Crossover Log #4 Installing Logs CCL3924NR and CCL3930NROperating Heater For Your Safety Read Before LightingLighting Instructions Unvented Natural GAS LOG Heater Operating Manual Lighting ProcedureTo Turn OFF GAS To Appliance Optional Remote OperationPilot Flame Pattern Inspecting BurnersMain Burner Cghrcta Series OperationService Hints Unvented Natural GAS LOG Heater Cleaning and MaintenanceTechnical Service Cleaning Burner Injector Holder and Pilot AIR Inlet HoleObserved Problem Possible Cause Remedy TroubleshootingMaintenance, Unvented Natural GAS LOG Heater TroubleshootingGas leak. See Warning statement at CGD3924NRA Unvented Natural GAS LOG Heater Illustrated Parts BreakdownKEY Part Number Description QTY Parts ListCCL3924NR CCL3930NR KEY CCL3924NR CCL3930NR Part Number Description QTY Parts not Under Warranty Parts Under WarrantySpecifications AccessoriesWiring Diagram Warranty Information

CCL3924NR, CCL3930NR specifications

The Desa CCL3930NR and CCL3924NR are advanced heating solutions known for their efficiency and innovative features. These models stand out in the market due to their commitment to both performance and user convenience.

One of the defining characteristics of both models is their energy efficiency. They utilize cutting-edge technology that optimizes fuel consumption while delivering robust heating output. The CCL3930NR, in particular, is designed for larger spaces, providing up to 30,000 BTUs, making it an excellent choice for garages, workshops, or any sizable area requiring reliable warmth. On the other hand, the CCL3924NR is geared toward medium-sized spaces, offering a maximum of 24,000 BTUs, making it suitable for residential settings or smaller commercial environments.

Both units feature a user-friendly thermostat that enables easy temperature control, contributing to user comfort and convenience. This digital thermostat allows for precise temperature settings, ensuring the environment remains consistent and cozy. The programmable features also provide flexibility, allowing users to set schedules according to their needs.

Another significant aspect of these models is their safety technologies. Equipped with robust safety mechanisms, both the CCL3930NR and the CCL3924NR automatically shut off in case of overheating or if the flame goes out unexpectedly. This ensures peace of mind for users, especially in settings where safety is paramount.

The construction of these heaters reflects durability and intention. They are built with high-quality materials designed to withstand the test of time, ensuring longevity and consistent performance. The sleek design also offers aesthetic appeal, allowing them to fit seamlessly into various environments.

In terms of fuel types, both models are versatile, accommodating a variety of fuels such as propane and kerosene, making them adaptable to different user preferences and availability of fuel sources. This flexibility is further enhanced by the portability of the units, enabling easy relocation as spaces or heating needs change.

In conclusion, the Desa CCL3930NR and CCL3924NR represent cutting-edge heating solutions that combine efficiency, safety, and user-friendly features. Whether for personal or professional use, these models offer an effective way to ensure comfort in various environments.
Top Page Image Contents