Desa VF-24P-PJD,VF-24N-PJD, VF-18N-PJD, VF-18P-PJD Local Codes, Unpacking, Product Features

Page 5
LOCAL CODES

LOCAL CODES

Install and use heater with care. Follow all local codes. In the absence of local codes, use the lat- est edition of The National Fuel Gas Code ANSI Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

UNPACKING

UNPACKINGCAUTION: Do not remove the data plates from the grate as- sembly. The data plates contain important warranty and safety information.

1.Remove log set assembly from carton. Note: Do not pick up assembly by logs. This could damage heater. Always handle assembly by grate.

2.Remove control cover floor media components.

3.Remove all protective packaging applied to log set for shipment.

3.Check all items for any shipping damage. If damaged, promptly inform dealer where you bought heater.

PRODUCT FEATURES

OPERATION

This heater is clean burning. It requires no outside venting. There is no heat loss out a vent or up a chimney. Heat is generated by realistic flames and glowing ceramic logs/coals. This heater is designed for vent-free operation with flue damper closed. It has been tested and approved toANSI Z21.11.2 standard for unvented heaters. State and local codes in some areas prohibit the use of vent-free heaters.

SAFETY PILOT

This heater has a pilot with an Oxygen Deple- tion Sensing (ODS) safety shutoff system. The ODS/pilot is a required feature for vent-free room heaters. The ODS/pilot shuts off the heater if there is not enough fresh air.

REMOTE IGNITION AND CONTROL

This gas log set has a battery powered electronic remote ignition and control. This system requires no matches or other source to light log set.

AIR FOR COMBUSTION

AND VENTILATION

PRODUCT FEATURES WARNING: This heater shall not be installed in a confined space or unusually tight con- struction unless provisions are provided for adequate combus- tion and ventilation air. Read the following instructions to insure proper fresh air for this and other fuel-burning appliances in your home.

Todayʼs homes are built more energy efficient than ever. New materials, increased insulation and new construction methods help reduce heat loss in homes. Home owners weather strip and caulk around windows and doors to keep the cold air out and the warm air in. During heating months, home owners want their homes as airtight as possible.

While it is good to make your home energy efficient, your home needs to breathe. Fresh air must enter your home. All fuel-burning appliances need fresh air for proper combustion and ventilation.

Exhaust fans, fireplaces, clothes dryers and fuel burning appliances draw air from the house to operate. You must provide adequate fresh air for these appliances. This will insure proper venting of vented fuel-burning appliances.

PROVIDING ADEQUATE

VENTILATION

The following are excerpts from National Fuel Gas Code, ANSI Z223.1/NFPA 54, Section 5.3, Air for Combustion and Ventilation.

All spaces in homes fall into one of the three fol- lowing ventilation classifications:

1.Unusually Tight Construction

2.Unconfined Space

3.Confined Space

The information on pages 5 through 7 will help you classify your space and provide adequate ventilation.

Unusually Tight Construction

The air that leaks around doors and windows may provide enough fresh air for combustion and ven- tilation. However, in buildings of unusually tight construction, you must provide additional fresh air.

111826-04A

www.desatech.com

5

Image 5
Contents WHAT TO DO IF YOU SMELL GAS TABLE OF CONTENTS SAFETY INFORMATION PRODUCT IDENTIFICATION SAFETY INFORMATIONContinued Figure 1 - Product IdentificationSAFETY PILOT PRODUCT FEATURESLOCAL CODES UNPACKINGContinued AIR FOR COMBUSTION AND VENTILATIONDETERMINING FRESH-AIRFLOW FOR HEATER LOCATION Confined and Unconfined SpaceContinued AIR FOR COMBUSTION AND VENTILATIONVentilation Air From Inside Building Ventilation Air From OutdoorsWARNING Never install the heater INSTALLATIONin a bedroom or bathroom in a recreational vehicleIf Not Using Mantel INSTALLATIONIf Using Mantel ContinuedSafe Installation INSTALLATIONContinued Materialoperate the logs only with the flue damper open INSTALLATIONraise the mantel to an accept- able height remove the mantelCONNECTING TO GAS SUPPLY INSTALLATIONPRESSURE TESTING GAS SUPPLY PIPING SYSTEM INSTALLATIONCHECKING GAS CONNECTIONS Natural GasPRESSURE TESTING HEATER GAS CONNECTIONS INSTALLATIONOPERATING HEATER ContinuedREMOTE LIGHTING INSTRUCTIONS OPERATING HEATERContinued Setting The Display C/24h and F /12h Shut-offProcedureSetting The Time Battery Replacement1.STOP! Read the safety information on page Set Timer5.Make sure ON/OFF switch is in -ON position 2.STOP! Read safety information on pagesee Troubleshooting, page see Troubleshooting, pageOPERATING HEATER INSPECTING BURNERSCLEANING AND MAINTENANCE OBSERVED PROBLEM TROUBLESHOOTINGPOSSIBLE CAUSE REMEDYsee Cleaning and Mainte TROUBLESHOOTINGContinued Burner backfiring during comWARNING If you smell gas Shut off gas supply TROUBLESHOOTINGWIRING DIAGRAM TROUBLESHOOTINGIDENTIFYING ERROR SIGNALS FROM RECIEVER OBSERVED PROBLEMTECHNICAL SERVICE SERVICE HINTSREPLACEMENT PARTS PARTS UNDER WARRANTYACCESSORIES SPECIFICATIONSVF-18N-PJD VF-24N-PJDMODELS VF-18N-PJDAND VF-18P-PJD ILLUSTRATED PARTS BREAKDOWNPARTS LIST MODELS VF-24N-PJDAND VF-24P-PJD ILLUSTRATED PARTS BREAKDOWNChassis PARTS LIST111826-04A 111826-04A LIMITED WARRANTY VENT-FREEGAS LOG HEATERS WARRANTY INFORMATIONKEEP THIS WARRANTY