Quadra-Fire QUADRA-FIRE CONTOUR warranty Component Information, Power Supply

Page 15

Contour Pellet Stove

COMPONENT INFORMATION

1.POWER SUPPLY

a.Check the wall receptacle for 120 volt, 60 Hz (standard current). Make sure the outlet is grounded and has the correct polarity.

2.FUSE

a.The fuse is on the front of the junction box, located on the right side of the stove. To access fuse, open the right side panel. To inspect the fuse, push the fuse holder in and turn the holder cap counterclockwise, then pull out. Replace with a standard 7 amp 120 volt fuse, if necessary. If the fuse continues to blow, contact your local dealer.

3.RED CALL LIGHT

a.The red call light is located on the right side next to the fuse. The function of the red call light is to indicate that the thermostat is calling for heat.

b.If the thermostat is calling for heat, the stove is burning, and the light is not on, check the bulb. Replace with a 28 volt AC (#85 lamp) bulb.

4.RESET BUTTON

a.The reset button is located on the back of the stove in the upper right hand corner just below the heat output switch (see Fig. A on page 12). The function of the button is to momentarily open the thermostat circuit, which restarts the system. However, this will only work when the thermostat is calling for heat and the red light is on.

b.If the light is on, there is no fire, and there is fuel in the firepot, push the reset button and wait for ignition. You should have a fire within five minutes.

c.If the light does not go out when the reset button is pushed, the reset button switch may be faulty. Contact your local dealer.

5.VACUUM SWITCH

a.The vacuum switch is located on the right side of the stove. This switch turns the feed system on when vacuum is present in the firebox. Check the rubber hose for leaks or cracks if the feed system fails to start. Also, be sure there is no restriction in the exhaust system and the exhaust blower is running. The vacuum switch is a safety device to shut off the feed motor under the conditions below.

b.If the exhaust or the heat exchanger system is dirty or plugged, the vacuum switch will keep the feed system from starting.

c.If the firebox door is open, the vacuum switch will keep the feed system from starting.

6.JUNCTION BOX AND WIRING HARNESS

a.The junction box is located on the right side of the stove. It contains the heat output controls, reset button, call light and fuse holder.

b.The junction box and the wiring harness are replaced as one component.

7.THERMOSTAT

a.The stove is designed to run on a 24 volt AC thermostat.

NOTE: The heat anticipator should be set on the lowest setting available. Also, check the wire leads at the terminal block located at the back of the stove for loose connections.

8.CONTROL BOX

a.The control box plugs into the side of the junction box. It is secured by a retainer bracket for shipping purposes only. To access the control box, simply bend the retainer bracket out of the way.

Note: After 2 or 3 bends, the bracket will break off. Discard the broken piece.

If the stove has just been plugged in and the combustion blower does not start, check snap disc #3, then check to make sure the stove is plugged in. Next, check the control box to see that it is securely plugged in. Also check the fuse to see that it is not blown. If this does not solve the problem, consult your local dealer.

NOTE: To see the temperature indicator lights, the right side panel must be open.

b.The green light located on the top of the control box notifies you that the stove has reached a temperature of 200°F (93°C) in the firepot. After the stove is lit, if this light does not light in the first four minutes of operation, the stove will shut down. Check the thermocouple.

c.The red light located in front of the green light is to indicate that the stove has reached operating

October 10, 2001

15

250-5583

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Important Safety Notes INSTALLATION, OPERATION, and Maintenance InstructionsContour Pellet Stove Table of Contents Label Location Behind Left Side Curtain on Outside of Hopper Safety LabelDimensions Listings and SpecificationsClearances to Combustibles Venting Pipe Table Chimney and Exhaust ConnectionVent Termination Requirements Venting GraphVenting Systems AlcoveThrough the Wall Masonry Venting SYSTEMS, ContdVertical Through the Wall & VerticalTOP Vent Flue Adapter Installation Feed AdjustmentFuel Adjustment Rod Wing Nut LOG SET Placement Instructions Piece LOG SET InstallationOptional Firepot Twig Installation Fuel Size and Material Wood Pellets Mobile Home InstallationThermostat Installation Operating InstructionsGeneral Operation Information Operating InstructionsStart Your First Fire Heat Output ControlsCleaning and Maintenance FirepotFirebox ASH Removal Soot and FLY ASH Formation and Need for Removal Cleaning and Maintenance ContdReading the Fire and Adjustment Procedures BlowersComponent Information Power SupplyThermocouple Component INFORMATION, ContdIgniter Component Information ContdTroubleshooting Troubleshooting Contd Wiring Harness Large FIRE, ASH Buildup and Dirty GlassUnit BURNING, no Call Light Hose Clamp Collar Assembly See FigFlex Hose 811-0820 Trim Ring Installation InstructionsPlace. See Fig Trim Ring INSTRUCTIONS, ContdBlower Remove Wires from Lower Rear Screen Exhaust Blower Replacement Instructions 812-4400See Figure TOP Baffle Removal InstructionsService Parts AccessoriesLifetime Warranty Division of Hearth Technologies Inc

QUADRA-FIRE CONTOUR specifications

The Quadra-Fire Contour is a remarkable addition to the realm of contemporary heating solutions, marrying elegant design with cutting-edge technology to deliver an efficient and user-friendly experience. Designed for versatility, the Contour is a superb choice for homeowners seeking efficient heating options that also enhance the beauty of their living spaces.

One of the standout features of the Quadra-Fire Contour is its impressive heating capacity. It can deliver up to 2,000 square feet of warmth, making it ideal for both smaller and larger areas. This flexibility allows homeowners to reduce their reliance on traditional heating systems, potentially lowering energy costs during colder months.

The Contour is equipped with Quadra-Fire’s renowned Advanced Combustion Technology, which optimizes fuel efficiency and reduces emissions. This technology ensures a clean burn while extracting maximum heat from the fuel, allowing users to enjoy extended burn times with minimal refueling. With its ability to operate with different fuel options, including wood and pellets, the Contour caters to various preferences and needs.

A key characteristic of the Contour is its stylish aesthetic. With a sleek and modern appearance, this stove seamlessly fits into any decor. The large viewing window provides an inviting view of the flames, adding a cozy ambiance to any setting. This not only enhances the atmosphere but also provides a functional heating source without compromising on style.

Featuring a user-friendly control system, the Quadra-Fire Contour allows for easy operation. The intuitive controls enable users to adjust the heat output and air control settings with ease. This ensures a customizable experience, as one can easily modify the stove's performance to suit their specific heating requirements.

In terms of installation, the Contour offers flexible venting options, allowing for both direct venting and conventional chimney setups. This versatility ensures that homeowners can easily integrate the stove into their existing infrastructure without significant modifications.

In conclusion, the Quadra-Fire Contour stands out as a leading choice for efficient and stylish home heating. Its advanced technology, impressive heating capabilities, and aesthetic appeal make it a valuable addition to any home. Whether you're looking to enhance your living space or invest in an efficient heating solution, the Contour provides an answer that combines form and function seamlessly.
Top Page Image Contents