Quadra-Fire QUADRA-FIRE CONTOUR warranty Exhaust Blower Replacement Instructions 812-4400

Page 24

Contour Pellet Stove

Exhaust Blower Replacement Instructions

Part #812-4400

Included in Kit: (1) Blower; (1) Gasket

FIG.1

CONTOUR SHOWN WITH TOP REAR SCREEN AND VACUUM SWITCH

REMOVED.Exhaust

Blower

Remove

wires from

Blower

Lower Rear Screen

1. Unplug stove.

2.Remove both side curtains by opening halfway, then lifting up and pulling back.

3.Disconnect vacuum hose and both wires (orange and red) from the vacuum switch so you can remove the top rear screen.

4.Unscrew and remove top rear screen.

5.Unscrew lower rear screen, and lay it on it's back as shown in Fig. 1.

Tools Required: Phillips Screwdriver; Flathead Screwdriver or 1/4" Nutdriver.

FIG. 2

6.Remove both wires from exhaust blower (blue and double white).

7.Remove 6 screws using a flathead screwdriver or a 1/4" nutdriver. Retain screws for use on replacement blower. See Fig 2.

8.Remove exhaust blower and gasket.

9.Install new gasket and blower by reversing steps 1-8.

FEED MOTOR Replacement Instructions

Part #812-4420 Feed motor

FIG. 1

FIG. 2

Molex Connectors

Feed Motor Mount Screws

mounting

Auger shaft set screw

Rectangular nylon bearing

1.UNPLUG THE STOVE.

2.Open the right Side Curtain to expose the Feed Motor.

3.Disconnect the Molex connectors. Remove the two screws from the Feed Motor Mount. (Figure 1)

4.Pull the Feed Motor/Auger assembly straight out towards you, being careful not to hit the Control Box.

5.Loosen set screw that secures Auger Shaft to Feed Motor Shaft. (See Figure 2), Remove 4 screws attaching Feed Motor to mount. Lift off old motor and replace with new. Secure with screws. Ensure Auger Shaft set screw aligns with flat side of Feed Motor Shaft.

6.Re-assemble in reverse order.

October 10, 2001

24

250-5583

Page 23 Page 25
Image 24
Page 23 Page 25
Contents INSTALLATION, OPERATION, and Maintenance Instructions Important Safety NotesContour Pellet Stove Table of Contents Safety Label Label Location Behind Left Side Curtain on Outside of HopperDimensions Listings and SpecificationsClearances to Combustibles Chimney and Exhaust Connection Vent Termination RequirementsVenting Graph Venting Pipe TableVenting Systems AlcoveThrough the Wall Venting SYSTEMS, Contd VerticalThrough the Wall & Vertical MasonryTOP Vent Flue Adapter Installation Feed AdjustmentFuel Adjustment Rod Wing Nut LOG SET Placement Instructions Piece LOG SET InstallationOptional Firepot Twig Installation Mobile Home Installation Thermostat InstallationOperating Instructions Fuel Size and Material Wood PelletsOperating Instructions Start Your First FireHeat Output Controls General Operation InformationCleaning and Maintenance FirepotFirebox ASH Removal Cleaning and Maintenance Contd Reading the Fire and Adjustment ProceduresBlowers Soot and FLY ASH Formation and Need for RemovalPower Supply Component InformationComponent INFORMATION, Contd ThermocoupleComponent Information Contd IgniterTroubleshooting Troubleshooting Contd Wiring Harness Large FIRE, ASH Buildup and Dirty GlassUnit BURNING, no Call Light Hose Clamp Collar Assembly See FigFlex Hose Trim Ring Installation Instructions 811-0820Trim Ring INSTRUCTIONS, Contd Place. See FigExhaust Blower Replacement Instructions 812-4400 Blower Remove Wires from Lower Rear ScreenTOP Baffle Removal Instructions See FigureAccessories Service PartsLifetime Warranty Division of Hearth Technologies Inc

QUADRA-FIRE CONTOUR specifications

The Quadra-Fire Contour is a remarkable addition to the realm of contemporary heating solutions, marrying elegant design with cutting-edge technology to deliver an efficient and user-friendly experience. Designed for versatility, the Contour is a superb choice for homeowners seeking efficient heating options that also enhance the beauty of their living spaces.

One of the standout features of the Quadra-Fire Contour is its impressive heating capacity. It can deliver up to 2,000 square feet of warmth, making it ideal for both smaller and larger areas. This flexibility allows homeowners to reduce their reliance on traditional heating systems, potentially lowering energy costs during colder months.

The Contour is equipped with Quadra-Fire’s renowned Advanced Combustion Technology, which optimizes fuel efficiency and reduces emissions. This technology ensures a clean burn while extracting maximum heat from the fuel, allowing users to enjoy extended burn times with minimal refueling. With its ability to operate with different fuel options, including wood and pellets, the Contour caters to various preferences and needs.

A key characteristic of the Contour is its stylish aesthetic. With a sleek and modern appearance, this stove seamlessly fits into any decor. The large viewing window provides an inviting view of the flames, adding a cozy ambiance to any setting. This not only enhances the atmosphere but also provides a functional heating source without compromising on style.

Featuring a user-friendly control system, the Quadra-Fire Contour allows for easy operation. The intuitive controls enable users to adjust the heat output and air control settings with ease. This ensures a customizable experience, as one can easily modify the stove's performance to suit their specific heating requirements.

In terms of installation, the Contour offers flexible venting options, allowing for both direct venting and conventional chimney setups. This versatility ensures that homeowners can easily integrate the stove into their existing infrastructure without significant modifications.

In conclusion, the Quadra-Fire Contour stands out as a leading choice for efficient and stylish home heating. Its advanced technology, impressive heating capabilities, and aesthetic appeal make it a valuable addition to any home. Whether you're looking to enhance your living space or invest in an efficient heating solution, the Contour provides an answer that combines form and function seamlessly.
Top Page Image Contents