Quadra-Fire QUADRA-FIRE CONTOUR warranty TOP Vent Flue Adapter Installation, Feed Adjustment

Page 9

Contour Pellet Stove

TOP VENT FLUE ADAPTER INSTALLATION

Part #811-0860, 3"-3" Top Vent Adapter or Part #812-3570, 3"-6" Offset Collar

1)Put a layer of silicone on the 3" (76mm) exhaust outlet.

2)Slide the flue adapter onto the rear exhaust outlet.

3)Adjust the assembly to a vertical position.

4)Drill four holes with #26 drill bit (provided) into the back of the stove using the outer shield as a pattern (make sure the assembly is vertical).

5)Install the four mounting screws.

6)Drill two holes with #26 drill bit through the Rear Exhaust Outlet using the two holes already in the short horizontal pipe in the Top Vent Adapter as a guide. Install the two screws

7)Install the stove pipe into the adapter (be sure to silicone all joints).

8)To clean adapter, remove cleanout cover.

Use hole on each

side as drilling guide

Rear Exhaust

Outlet

FEED ADJUSTMENT

Mount with four screws

NOTES:

The feed adjustment rod is factory set, and should be adequate for most fuels. However, if the flame height is too high or too low, follow the instructions below.

Loosen the set screw (Fig. 1) 1/4 to 1/2 turn during set-up of stove. This will allow movement of the Fuel Adjustment Rod. Do not re-tighten set screw.

Adjust fuel adjustment rod after the stove has been burning for 10-15 minutes. The flames should be approximately 4"(102mm) above the firepot at high heat output setting.

Cleanout Cover

1)Loosen the wing nut.

2)Adjust the fuel adjustment rod upward towards the "+" symbol, to increase the feed rate and flame height, or down towards the "-" symbol, to decrease the feed rate and flame height.

3)Re-tighten the wing nut.

FIGURE 1

FIGURE 2

Fuel Adjustment Rod

Wing Nut

October 10, 2001

9

250-5583

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Important Safety Notes INSTALLATION, OPERATION, and Maintenance InstructionsContour Pellet Stove Table of Contents Label Location Behind Left Side Curtain on Outside of Hopper Safety LabelDimensions Listings and SpecificationsClearances to Combustibles Vent Termination Requirements Chimney and Exhaust ConnectionVenting Graph Venting Pipe TableVenting Systems AlcoveThrough the Wall Vertical Venting SYSTEMS, ContdThrough the Wall & Vertical MasonryTOP Vent Flue Adapter Installation Feed AdjustmentFuel Adjustment Rod Wing Nut LOG SET Placement Instructions Piece LOG SET InstallationOptional Firepot Twig Installation Thermostat Installation Mobile Home InstallationOperating Instructions Fuel Size and Material Wood PelletsStart Your First Fire Operating InstructionsHeat Output Controls General Operation InformationCleaning and Maintenance FirepotFirebox ASH Removal Reading the Fire and Adjustment Procedures Cleaning and Maintenance ContdBlowers Soot and FLY ASH Formation and Need for RemovalComponent Information Power SupplyThermocouple Component INFORMATION, ContdIgniter Component Information ContdTroubleshooting Troubleshooting Contd Wiring Harness Large FIRE, ASH Buildup and Dirty GlassUnit BURNING, no Call Light Hose Clamp Collar Assembly See FigFlex Hose 811-0820 Trim Ring Installation InstructionsPlace. See Fig Trim Ring INSTRUCTIONS, ContdBlower Remove Wires from Lower Rear Screen Exhaust Blower Replacement Instructions 812-4400See Figure TOP Baffle Removal InstructionsService Parts AccessoriesLifetime Warranty Division of Hearth Technologies Inc

QUADRA-FIRE CONTOUR specifications

The Quadra-Fire Contour is a remarkable addition to the realm of contemporary heating solutions, marrying elegant design with cutting-edge technology to deliver an efficient and user-friendly experience. Designed for versatility, the Contour is a superb choice for homeowners seeking efficient heating options that also enhance the beauty of their living spaces.

One of the standout features of the Quadra-Fire Contour is its impressive heating capacity. It can deliver up to 2,000 square feet of warmth, making it ideal for both smaller and larger areas. This flexibility allows homeowners to reduce their reliance on traditional heating systems, potentially lowering energy costs during colder months.

The Contour is equipped with Quadra-Fire’s renowned Advanced Combustion Technology, which optimizes fuel efficiency and reduces emissions. This technology ensures a clean burn while extracting maximum heat from the fuel, allowing users to enjoy extended burn times with minimal refueling. With its ability to operate with different fuel options, including wood and pellets, the Contour caters to various preferences and needs.

A key characteristic of the Contour is its stylish aesthetic. With a sleek and modern appearance, this stove seamlessly fits into any decor. The large viewing window provides an inviting view of the flames, adding a cozy ambiance to any setting. This not only enhances the atmosphere but also provides a functional heating source without compromising on style.

Featuring a user-friendly control system, the Quadra-Fire Contour allows for easy operation. The intuitive controls enable users to adjust the heat output and air control settings with ease. This ensures a customizable experience, as one can easily modify the stove's performance to suit their specific heating requirements.

In terms of installation, the Contour offers flexible venting options, allowing for both direct venting and conventional chimney setups. This versatility ensures that homeowners can easily integrate the stove into their existing infrastructure without significant modifications.

In conclusion, the Quadra-Fire Contour stands out as a leading choice for efficient and stylish home heating. Its advanced technology, impressive heating capabilities, and aesthetic appeal make it a valuable addition to any home. Whether you're looking to enhance your living space or invest in an efficient heating solution, the Contour provides an answer that combines form and function seamlessly.
Top Page Image Contents