Quadra-Fire CUMPGAP-PMH, CUMBGAP-MBK warranty Heat Output Settings Building a Fire, Burn Rates

Page 28

R

Cumberland Gap Wood Stove

F. Heat Output Settings

H. Building A Fire

For maximum operating efficiency with the lowest emissions, follow these operating procedures:

1.Regardless of desired heat output, when loading stove, burn it with both air controls wide open for 5 to 15 min- utes.

2.Regulate burn rate (heat output) by using the Primary Air Slide Control (center under ashcatcher). The Start-Up Air Control (on the right) is used for initial start-up and reloading.

3.Heat output settings are listed below, following 5 to 15 minutes of burning with controls wide open (see #1 above):

4.Burn dry, well-seasoned wood.

G.Burn Rates

1. High Burn Rate - Maximum Heat* - 30,000+ BTU/hr

•Close Start-Up Air Control after 5 to 15 minutes, fully open (slide all the way to the left) the Primary Air Slide Control.

2. Medium-High Burn Rate* - 15,000 to 30,000 BTU/hr

•Close Start-Up Air Control after 5 to 15 minutes, open the Primary Air Control 1/4 inch to 1 inch.

3. Medium-Low Burn Rate* - 10,000 to 15,000 BTU/hr

•Close Start-Up Air Control after 5 to 15 minutes, open the Primary Air Control 1/8 inch to 1/4 inch.

4. Low Burn Rate* - Below 10,000 BTU/hr

•Close Start-Up Air Control after 5 to 15 minutes. Gradu- ally close down (sliding to the right) the Primary Air Slide Control making sure to maintain flames in the stove. You must maintain flames during the first few hours of a low burn to avoid excessive air pollution.

*NOTE: These are approximate settings, and will vary with type of wood or chimney draft. Due to altitude and other environmental circumstances, this operational information is a guideline only.

WARNING

Risk of extreme temperatures!

•Do not operate with Start-Up Air Control in the open position in excess of 15 minutes!

•Prolonged operation with the Start-Up Air Control in the open position may cause the combustible materials around the stove to exceed safe temperature limits.

Before lighting your first fire make certain that the baffle and blanket are correctly positioned. They should be resting against the rear support.

There are many ways to build a fire. The basic principle is to light easily-ignitable tinder or paper, which ignites the fast burning kindling, which in turn ignites the slow-burning firewood. Here is one method that works well:

1. Place several wads of crushed paper on the firebox floor.

Heating the flue with slightly crumpled newspaper before adding kindling keeps smoke to a minimum.

2.Lay small dry sticks of kindling on top of the paper.

3.Open Start-Up Air Control and Primary Air Slide Control fully. After 5 to 15 minutes, when the fire is well established, gently pull Start-Up Air Control forward until resistance is felt. Do not allow control to "spring back" into the open position.

4.Make sure that no matches or other combustibles are in the immediate area of the stove. Be sure the room is adequately ventilated and the flue unobstructed.

5.Light the paper in the stove. NEVER light or rekindle stove with kerosene, gasoline, or charcoal lighter fluid; the results can be fatal.

6.Once the kindling is burning quickly, add several full-length logs 3 inches (76mm) or 4 inches (102mm) in diameter. Be careful not to smother the fire. Stack the pieces of wood carefully: near enough to keep each other hot, but far enough away from each other to allow adequate air flow between them.

7.When ready to reload the stove, add more logs. Large logs burn slowly, holding a fire longer. Small logs burn fast and hot, giving quick heat.

8.Adjust the Start-Up Air Control and Primary Air Slide Con- trol; the more you close down (slide right) the Primary Air Slide Control, the lower and slower the fire will burn. The more you open (slide left) the Primary Air Slide Control, the more heat will be produced. The Start-Up Air Control is only used for the first 5 to 15 minutes.

9.As long as there are hot coals, repeating steps 7 and 8 will maintain a continuous fire throughout the season.

NOTE: The special high temperature paint that your stove is finished with will cure as your stove heats. You will notice an odor and perhaps see some vapor rise from the stove surface; this is normal. We recommend that you open a window until the odor dissipates and paint is cured.

NOTE: Stove should be run full open for 15 minutes a day to keep air passages clean.

Page 28

7006-188G

November 5, 2010

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Cumberland Gap Non-Catalytic, Front/Side Load, Wood HeaterTesting Lab Cumberland Gap Wood StoveSerial Number Model NameTable of Contents Cumberland Gap Wood Stove Listing and Code Approvals Appliance CertificationBTU & Efficiency Specifications Mobile Home ApprovedFire Safety Design, Installation & Location ConsiderationsGetting Started Cumberland Gap Wood Stove Asphyxiation RiskNegative Pressure WindwardFlue Draft Considerations Venting SystemsTools And Supplies Needed Inspect Appliance & Components and Pre-Burn Check ListTypical Stove Systems Stove system with masonry chimney consists of FigureDimensions and Clearances Appliance DimensionsSingle Wall-USA Clearances To Combustibles UL And ULCDouble Wall-USA Installation Considerations Hearth Protection RequirementsCalculating Alternate Floor Protection Material USA Required Canada RecommendedReversible Flue Collar and Horizontal Flue Heat Shield Completed ViewBaffle Diverter Baffle DiverterFire Risk Slanted corner Straight end to the backCumberland Gap Wood Stove Baffle Diverter Is shipped Inside fireboxCut Ends Hand Bend #1 Hand bend #2 Straight End Side Fuel-Loading-Door Locking Mechanism Leg Leveling SystemInstructions To Unlock Side Fuel Door Outside Air Kit Installation Installation Of Optional Blower Venting Components Cumberland Gap Wood Stove Chimney RequirementsChimney Systems Air Clearances ComponentsInstructions Masonry Chimney Liner Chimney Height / Rise and RunInstalling Chimney Components Masonry Chimney Liner ContdChimney Termination Requirements RuleCumberland Gap Wood Stove Mobile Home Installation 629M, Standard for Factory Built ChimneysAdjusting The Blower Speed Control Cumberland Gap Wood Stove Appliance Set-UpDoor Handle Assemblies Needs to move smoothlyCumberland Gap Wood Stove Operating Instructions Over-Firing Your Appliance Wood Selection and StorageHardwood vs Softwood Processed Solid Fuel Fire LogsBurning Process MoistureSeasoned Wood Storing WoodAir Controls Combustible/Non-Combustible MaterialsFinal Stage Start-Up Air SystemHeat Output Settings Building a Fire Burn RatesHigh Burn Rate Maximum Heat* 30,000+ BTU/hr Medium-Low Burn Rate* 10,000 to 15,000 BTU/hrOptional Blower Operating Instructions Opacity SmokeFrequently Asked Questions Clear SpaceCorrect Baffle & Blanket Placement Incorrect PositionsGeneral Maintenance Creosote Chimney CleaningAsh Removal System ARS Operating and Cleaning Injury RiskGlass Cleaning Frequency As desired Cleaning Plated SurfacesWhen cleaning glass Disposal of AshesInspect Firebrick & Replacement Instructions Glass ReplacementAppliance Inspection Routine Fire Risk Injury RiskBaffle Removal & Installation Quick Reference Maintenance Guide MonthlyCumberland Gap Wood Stove Troubleshooting Guide Start Fire Problems Possible Cause SolutionService Parts Stocked Service PartsAt Depot Stocked at Depot #20 Brick SetCumberland Gap Warranty Policy November 5 7006-188G Contact Information

CUMBGAP-MBK, CUMPGAP-PMH specifications

The Quadra-Fire CUMPGAP-PMH and CUMBGAP-MBK are established models in the realm of high-efficiency wood stoves, combining modern technology with traditional heating methods to provide an effective and environmentally friendly heating solution.

One of the standout features of the CUMPGAP-PMH and CUMBGAP-MBK models is their impressive heating efficiency. Both stoves exceed industry standards, ensuring that more heat is produced from less fuel, which not only helps in saving on heating costs but also reduces the environmental impact. Their efficient combustion technology means that these stoves produce minimal emissions, making them a responsible choice for eco-conscious consumers.

The construction of these stoves is designed with durability and robustness in mind. Made from high-quality materials, they assure longevity and reliability, which are crucial elements in heating appliances. The intelligently engineered airflow dynamics facilitate efficient burning, allowing these models to maintain optimal performance under various conditions.

Another significant feature of both models is the incorporation of advanced catalytic combustors. These catalysts improve the combustion process, resulting in cleaner burning and enhancing overall efficiency. The catalytic technology functions by allowing smoke and gases to pass through the catalyst, where they undergo additional burning before being released into the atmosphere. This process not only maximizes heat generation but also significantly lowers the emissions of harmful pollutants.

User convenience is also a top priority with these wood stoves. They feature large ash pans and simple loading mechanisms, making it easy to maintain and use them regularly. Their stylish design allows them to fit seamlessly into any home décor, and with variable heating capacities, they can effectively warm spaces of different sizes.

Safety features are another vital characteristic of the CUMPGAP-PMH and CUMBGAP-MBK models. With built-in heat shields and thermal protection, they provide peace of mind to homeowners while promoting safer operation. Additionally, they comply with various safety and efficiency standards set by regulatory bodies.

In conclusion, the Quadra-Fire CUMPGAP-PMH and CUMBGAP-MBK models stand out for their efficiency, design, advanced combustion technology, and safety features. They offer a modern solution to traditional wood heating, ensuring warmth and comfort while taking care of the environment. These stoves represent the perfect synergy of innovation and effectiveness in home heating solutions.
Top Page Image Contents