Quadra-Fire CUMPGAP-PMH, CUMBGAP-MBK General Maintenance, Creosote Chimney Cleaning, Injury Risk

Page 32

R

Cumberland Gap Wood Stove

9

Maintaining & Servicing Your Appliance

A. General Maintenance

1.Creosote (Chimney) Cleaning

•Frequency: Every 2 months during heating season or as recommended by a certified chimney sweep; more frequently if chimney exceeds or is under 12-14 ft. (measured from base of appliance).

•By: Certified Chimney Sweep

1.Remove all ash from the firebox and extinguish all hot embers before disposal. Allow the appliance to cool completely. It is also recommended that before each heating season the entire system be professionally inspected, cleaned and repaired if necessary.

2.Close the door tightly and proceed with sweeping the chimney.

3.Sweep the collected ashes into the ash removal box, and empty. Clean out the remaining ashes from firebox.

4.Open top-loading door and vacuum out.

Inspection: Inspect the system at the appliance connection and at the chimney top. Cooler surfaces tend to build creosote deposits quicker, so it is important to check the chimney from the top as well as from the bottom.

Formation and Need For Removal: When wood is burned slowly, it produces tar and other organic vapors which combine with expelled moisture to form creosote.

The creosote vapors condense in the relatively cool chimney flue of a newly-started or a slow-burning fire. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote creates an extremely hot fire which may damage the chimney or even destroy the house.

The chimney connector and chimney should be inspected once every 2 months during the heating season to determine if a creosote or soot buildup has occurred. If creosote or soot has accumulated, it should be removed to reduce the risk of a chimney fire.

WARNING

Fire Risk.

Prevent creosote buildup.

•Inspect chimney connector and chimney once every two months during heating season.

•Remove creosote to reduce risk of chimney fire.

•Ignited creosote is extremely HOT.

WARNING

Fire Risk.

•Do not use chimney cleaners or flame colorants in your appliance.

Will corrode pipe.

2.Ash Removal System (ARS) Operating and Cleaning

•Frequency: Weekly when in constant operation or as needed.

•By: Homeowner

CAUTION

Injury Risk.

•Gloves recommended

•Ash coals can remain extremely hot for several days.

1.The stove and ashes must be completely cooled down before using the Ash Removal System. The hinged door will open from the right hand side. Pull ash pan out carefully.

2.Clean ash down through the ash removal system grate into the drawer below. If there are large pieces in the ashes, you can remove the grate before brushing the ash into the drawer.

3.Be sure to replace the grate before operating the stove. Remember to leave 1/4 to 1/2 inch (6-13mm) of ash on the firebox floor to act as a natural grate, allowing air to flow freely underneath wood

4.Replace ash pan and close ash door handle. Dispose of the ashes following the directions on page 33.

 

Ash Door

Swings Open

Handle

 

Figure 32.1

Do not allow ashes to build up in the ashpan until they reach the grate. This will lead to premature deterioration of the grate and make it difficult to empty the ash pan.

WARNING

Fire risk

Injury risk

Make sure ash removal system door

Air leakage may cause:

•Over-fire condition.

•Flame and/or smoke spillage.

•Wood to burn too fast.

Do not operate with ash pan door open or with ash pan removed

Page 32

7006-188G

November 5, 2010

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Cumberland Gap Non-Catalytic, Front/Side Load, Wood HeaterTesting Lab Cumberland Gap Wood StoveSerial Number Model NameTable of Contents Cumberland Gap Wood Stove Listing and Code Approvals Appliance CertificationBTU & Efficiency Specifications Mobile Home ApprovedFire Safety Design, Installation & Location ConsiderationsGetting Started Cumberland Gap Wood Stove Asphyxiation RiskNegative Pressure WindwardFlue Draft Considerations Venting SystemsTools And Supplies Needed Inspect Appliance & Components and Pre-Burn Check ListTypical Stove Systems Stove system with masonry chimney consists of FigureDimensions and Clearances Appliance DimensionsDouble Wall-USA Clearances To Combustibles UL And ULCSingle Wall-USA Installation Considerations Hearth Protection RequirementsCalculating Alternate Floor Protection Material USA Required Canada RecommendedReversible Flue Collar and Horizontal Flue Heat Shield Completed ViewBaffle Diverter Baffle DiverterFire Risk Slanted corner Straight end to the backCut Ends Hand Bend #1 Hand bend #2 Straight End Baffle Diverter Is shipped Inside fireboxCumberland Gap Wood Stove Instructions To Unlock Side Fuel Door Leg Leveling SystemSide Fuel-Loading-Door Locking Mechanism Outside Air Kit Installation Installation Of Optional Blower Chimney Systems Cumberland Gap Wood Stove Chimney RequirementsVenting Components Instructions ComponentsAir Clearances Masonry Chimney Liner Chimney Height / Rise and RunInstalling Chimney Components Masonry Chimney Liner ContdChimney Termination Requirements RuleCumberland Gap Wood Stove Mobile Home Installation 629M, Standard for Factory Built ChimneysAdjusting The Blower Speed Control Cumberland Gap Wood Stove Appliance Set-UpDoor Handle Assemblies Needs to move smoothlyCumberland Gap Wood Stove Operating Instructions Over-Firing Your Appliance Wood Selection and StorageHardwood vs Softwood Processed Solid Fuel Fire LogsBurning Process MoistureSeasoned Wood Storing WoodAir Controls Combustible/Non-Combustible MaterialsFinal Stage Start-Up Air SystemHeat Output Settings Building a Fire Burn RatesHigh Burn Rate Maximum Heat* 30,000+ BTU/hr Medium-Low Burn Rate* 10,000 to 15,000 BTU/hrOptional Blower Operating Instructions Opacity SmokeFrequently Asked Questions Clear SpaceCorrect Baffle & Blanket Placement Incorrect PositionsGeneral Maintenance Creosote Chimney CleaningAsh Removal System ARS Operating and Cleaning Injury RiskGlass Cleaning Frequency As desired Cleaning Plated SurfacesWhen cleaning glass Disposal of AshesInspect Firebrick & Replacement Instructions Glass ReplacementAppliance Inspection Routine Fire Risk Injury RiskBaffle Removal & Installation Quick Reference Maintenance Guide MonthlyCumberland Gap Wood Stove Troubleshooting Guide Start Fire Problems Possible Cause SolutionService Parts At Depot Service PartsStocked Stocked at Depot #20 Brick SetCumberland Gap Warranty Policy November 5 7006-188G Contact Information

CUMBGAP-MBK, CUMPGAP-PMH specifications

The Quadra-Fire CUMPGAP-PMH and CUMBGAP-MBK are established models in the realm of high-efficiency wood stoves, combining modern technology with traditional heating methods to provide an effective and environmentally friendly heating solution.

One of the standout features of the CUMPGAP-PMH and CUMBGAP-MBK models is their impressive heating efficiency. Both stoves exceed industry standards, ensuring that more heat is produced from less fuel, which not only helps in saving on heating costs but also reduces the environmental impact. Their efficient combustion technology means that these stoves produce minimal emissions, making them a responsible choice for eco-conscious consumers.

The construction of these stoves is designed with durability and robustness in mind. Made from high-quality materials, they assure longevity and reliability, which are crucial elements in heating appliances. The intelligently engineered airflow dynamics facilitate efficient burning, allowing these models to maintain optimal performance under various conditions.

Another significant feature of both models is the incorporation of advanced catalytic combustors. These catalysts improve the combustion process, resulting in cleaner burning and enhancing overall efficiency. The catalytic technology functions by allowing smoke and gases to pass through the catalyst, where they undergo additional burning before being released into the atmosphere. This process not only maximizes heat generation but also significantly lowers the emissions of harmful pollutants.

User convenience is also a top priority with these wood stoves. They feature large ash pans and simple loading mechanisms, making it easy to maintain and use them regularly. Their stylish design allows them to fit seamlessly into any home décor, and with variable heating capacities, they can effectively warm spaces of different sizes.

Safety features are another vital characteristic of the CUMPGAP-PMH and CUMBGAP-MBK models. With built-in heat shields and thermal protection, they provide peace of mind to homeowners while promoting safer operation. Additionally, they comply with various safety and efficiency standards set by regulatory bodies.

In conclusion, the Quadra-Fire CUMPGAP-PMH and CUMBGAP-MBK models stand out for their efficiency, design, advanced combustion technology, and safety features. They offer a modern solution to traditional wood heating, ensuring warmth and comfort while taking care of the environment. These stoves represent the perfect synergy of innovation and effectiveness in home heating solutions.
Top Page Image Contents