Quadra-Fire CUMBGAP-MBK, CUMPGAP-PMH warranty Baffle Removal & Installation

Page 35

R

Cumberland Gap Wood Stove

E. Baffle Removal & Installation

1.Remove all ash from firebox, and extinguish all hot embers before disposal into a metal container.

2.Remove ceramic blanket & baffle together

3.With a 3/16” Allen wrench, remove the front manifold tube retainer bolts on the air channel under the end of the front tube. Figure 35.1.

NOTE: Soak the bolts with penetrating oil for at least 15 minutes before trying to remove them.

4.To remove manifold tube, slide the tube to one side until one end is out of its hole. Then, while lifting that end of the fiber board baffle, pull tube up over the air channel and out of hole at the other end.

5.Slide fiber board baffle forward to front of stove and straight out through door. Figure 35.2.

6.To install the fiber board baffle, repeat steps 2 through 4 in reverse.

7.The front manifold tube is shorter than the back two. It is IMPORTANT that they are replaced in the correct position or your stove will not operate properly.

8.Be sure the fiber board baffle and ceramic blanket are fully pushed back into position and the blanket is down flat. The front of the blanket should be flush with the front of the baffle.

Baffle Board

Push baffle board up slightly to allow room to turn the handle

Figure 35.1

Ceramic Blanket

Baffle Board

Figure 35.2

November 5, 2010

7006-188G

Page 35

Image 35
Contents Non-Catalytic, Front/Side Load, Wood Heater Cumberland GapModel Name Testing LabCumberland Gap Wood Stove Serial NumberTable of Contents Mobile Home Approved Cumberland Gap Wood Stove Listing and Code ApprovalsAppliance Certification BTU & Efficiency SpecificationsAsphyxiation Risk Fire SafetyDesign, Installation & Location Considerations Getting Started Cumberland Gap Wood StoveWindward Negative PressureInspect Appliance & Components and Pre-Burn Check List Flue Draft ConsiderationsVenting Systems Tools And Supplies NeededStove system with masonry chimney consists of Figure Typical Stove SystemsAppliance Dimensions Dimensions and ClearancesDouble Wall-USA Clearances To Combustibles UL And ULCSingle Wall-USA Hearth Protection Requirements Installation ConsiderationsUSA Required Canada Recommended Calculating Alternate Floor Protection MaterialCompleted View Reversible Flue Collar and Horizontal Flue Heat ShieldSlanted corner Straight end to the back Baffle DiverterBaffle Diverter Fire RiskCut Ends Hand Bend #1 Hand bend #2 Straight End Baffle Diverter Is shipped Inside fireboxCumberland Gap Wood Stove Instructions To Unlock Side Fuel Door Leg Leveling SystemSide Fuel-Loading-Door Locking Mechanism Outside Air Kit Installation Installation Of Optional Blower Chimney Systems Cumberland Gap Wood Stove Chimney RequirementsVenting Components Instructions ComponentsAir Clearances Chimney Height / Rise and Run Masonry Chimney LinerMasonry Chimney Liner Contd Installing Chimney ComponentsRule Chimney Termination Requirements629M, Standard for Factory Built Chimneys Cumberland Gap Wood Stove Mobile Home InstallationNeeds to move smoothly Adjusting The Blower Speed ControlCumberland Gap Wood Stove Appliance Set-Up Door Handle AssembliesProcessed Solid Fuel Fire Logs Cumberland Gap Wood Stove Operating InstructionsOver-Firing Your Appliance Wood Selection and Storage Hardwood vs SoftwoodStoring Wood Burning ProcessMoisture Seasoned WoodStart-Up Air System Air ControlsCombustible/Non-Combustible Materials Final StageMedium-Low Burn Rate* 10,000 to 15,000 BTU/hr Heat Output Settings Building a FireBurn Rates High Burn Rate Maximum Heat* 30,000+ BTU/hrOpacity Smoke Optional Blower Operating InstructionsClear Space Frequently Asked QuestionsIncorrect Positions Correct Baffle & Blanket PlacementInjury Risk General MaintenanceCreosote Chimney Cleaning Ash Removal System ARS Operating and CleaningDisposal of Ashes Glass Cleaning Frequency As desiredCleaning Plated Surfaces When cleaning glassFire Risk Injury Risk Inspect Firebrick & Replacement InstructionsGlass Replacement Appliance Inspection RoutineBaffle Removal & Installation Monthly Quick Reference Maintenance GuideStart Fire Problems Possible Cause Solution Cumberland Gap Wood Stove Troubleshooting GuideService Parts At Depot Service PartsStocked #20 Brick Set Stocked at DepotCumberland Gap Warranty Policy November 5 7006-188G Contact Information

CUMBGAP-MBK, CUMPGAP-PMH specifications

The Quadra-Fire CUMPGAP-PMH and CUMBGAP-MBK are established models in the realm of high-efficiency wood stoves, combining modern technology with traditional heating methods to provide an effective and environmentally friendly heating solution.

One of the standout features of the CUMPGAP-PMH and CUMBGAP-MBK models is their impressive heating efficiency. Both stoves exceed industry standards, ensuring that more heat is produced from less fuel, which not only helps in saving on heating costs but also reduces the environmental impact. Their efficient combustion technology means that these stoves produce minimal emissions, making them a responsible choice for eco-conscious consumers.

The construction of these stoves is designed with durability and robustness in mind. Made from high-quality materials, they assure longevity and reliability, which are crucial elements in heating appliances. The intelligently engineered airflow dynamics facilitate efficient burning, allowing these models to maintain optimal performance under various conditions.

Another significant feature of both models is the incorporation of advanced catalytic combustors. These catalysts improve the combustion process, resulting in cleaner burning and enhancing overall efficiency. The catalytic technology functions by allowing smoke and gases to pass through the catalyst, where they undergo additional burning before being released into the atmosphere. This process not only maximizes heat generation but also significantly lowers the emissions of harmful pollutants.

User convenience is also a top priority with these wood stoves. They feature large ash pans and simple loading mechanisms, making it easy to maintain and use them regularly. Their stylish design allows them to fit seamlessly into any home décor, and with variable heating capacities, they can effectively warm spaces of different sizes.

Safety features are another vital characteristic of the CUMPGAP-PMH and CUMBGAP-MBK models. With built-in heat shields and thermal protection, they provide peace of mind to homeowners while promoting safer operation. Additionally, they comply with various safety and efficiency standards set by regulatory bodies.

In conclusion, the Quadra-Fire CUMPGAP-PMH and CUMBGAP-MBK models stand out for their efficiency, design, advanced combustion technology, and safety features. They offer a modern solution to traditional wood heating, ensuring warmth and comfort while taking care of the environment. These stoves represent the perfect synergy of innovation and effectiveness in home heating solutions.