Master Lock XR20 manual Area System Disarming, Disarming an Area System

Page 12

Area System Disarming

Disarming: While the system is armed, you can only enter the premises through an exit/entry delay door without causing an alarm. After opening the door, the Security Command keypad sounds a prewarn tone to remind you to disarm the system. You must disarm the system before the delay time expires or an alarm will occur.

During the prewarn tone, the keypad displays ENTER CODE: Enter your user code to disarm the system. Only those areas authorized for your user code will disarm.

All or Selective Arming: After entering your user code, the system allows you to disarm either all of the areas to which you have access or just selected areas. If you choose to disarm all areas, the system automatically disarms them. If you choose to disarm selected areas, the names of those areas will be displayed on the keypad.

Alarm Display: After disarming, the keypad displays any zones that went into alarm or any communication problems that occurred during the armed period. All burglary zones are then disarmed and any bypassed zones are automatically reset.

Disarmed Message: The keypad displays ALL SYSTEM OFF after the system disarms.

Central Station Report: A report of the disarming can be sent to the central station. If your system does not have this feature, it can be programmed for you at any time.

Disarming an Area System

1.Press the COMMAND key until ARM DISARM is displayed. During entry delay this process starts at step 3 below.

2.Select DISARM to disarm areas.

3.The keypad displays ENTER CODE: . Enter your user code. The keypad displays ALL? NO YES.

4.Select YES to disarm all areas authorized for your user code.

4a. Select NO to disarm only certain areas individually. The keypad then displays the name of each area authorized for your code followed by the NO YES display.

4b. Choose YES to disarm the area displayed.

4c. Choose NO to not disarm and to display the next area.

Note: You can also just press the area numbers you want to disarm while at the ALL? NO YES display. This changes the display to AREAS: . The area numbers you select appear in the display. For example: AREAS: 2 4.

To remove an area number from the display, press its corresponding number on the keypad.

Press COMMAND when done.

5.After all areas have been displayed, any alarms or communication problems that occurred during the armed period are shown.

6.If all areas have been disarmed, the keypad displays ALL SYSTEM OFF.

8

XR20 Arming and Disarming

Page 11 Page 13
Image 12
Page 11 Page 13
Contents XR20 All/Perimeter and Home/Away Systems Area SystemsSecurity Command Users Guide Decide where to meet Draw a floorplan of your home or businessDevelop escape routes Practice your escape plansSecurity Command keypad About Your Security SystemParts of the System Test Your System WeeklySecurity Command Keypad Character Keypad User Options MenuSelect keys Special Security Command Messages Special Security Command TonesSystem Trouble or Service Required Understanding Security System Terms Exit Error Central Station MonitoringStatus Armed StatusHow your System Operates Arming FunctionsArea System Arming Arming the SystemExample Office no YES Area System Disarming Disarming an Area SystemAll/Perimeter System Arming System Ready/System Not Ready Keypad DisplaysInstant Arming Arming an All/Perimeter SystemDisarming During an Alarm All/Perimeter System DisarmingDisarming an All/Perimeter System Home/Away System Arming Arming a Home/Away SystemEasy Exit Feature Home/Away System DisarmingDisarming a Home/Away System Security Command User Menu To access the User MenuUser Menu Options Menu Option DescriptionUser Check-in Zone Activity CheckSending a Check-in Report Selecting Zone Activity CheckSensor Reset Resetting the SensorsEnter your user code to reset sensors Outputs On OffUsing the Bypass Zones Function Bypass ZonesZone Monitor Using the Zone Monitor Function Using the System Test FunctionSystem Test User Codes User Code Authority LevelsAdding User codes Changing User codes 6a. Temp Code no YES6c. ARM only no YES Setting an Arming and Disarming Schedule Ambush CodesSchedules Deleting User codesSetting the Date and Time Extended SchedulesDate and Time Extending a Closing ScheduleUsing the Display Events Function Display EventsZone Activity Check Event Display BYP Bypass RST Restore Zone Bypass Event DisplaysZone Event Displays Arming and Disarming Event Displays User Check-in Event DisplaysUser Code Change Event Displays Supervisory Event DisplaysTest report was sent on Oct Station at the date and time shownService Request? System Monitor Event DisplaysAn AC failure occurred at 105 AM System Monitor Event Types There are 2 event typesSystem Setup Protection AreasOutputs HOW to Fill in this HOW to Fill in this Appendix Easy Entry Users GuideArming and Disarming AN ALL/PERIMETER System Using the Alert Buttons FA113 Users GuideArming a Home/Away or All/Perimeter System Disarming a Home/Away or All/Perimeter SystemPager Direct Users Guide Area NamesPager Direct Area NameNumeric Pager Display Alphanumeric Pager DisplayPhoneAccess Users Guide You will hearPress To do this You will hear Voice Module Message Meaning Possible Solutions Common Keypad DisplaysIndex This page has been intentionally left blank LT-0303 5/02
Top Page Image Contents