Napco Security Technologies GEM-K2AS manual R nO n / C h i me Y e s / N o

Page 19

FUNCTION MENU

A C O N

T u r nO n / C h i me Y e s / N o

Activate Chime? "MONITOR ON" will be displayed and the Chime Mode will sound a tone at the keypad when the programmed zone is opened while disarmed. To deactivate the Chime Mode, execute the "TurnOff Chime" function. Note: The Chime Mode is disabled while armed.

A C O N

T u r nO n / W a t c h Y e s / N o

Activate Watch Mode? (Watch Mode programmed? !YES !NO). This optional feature si- multaneously turns on all zones designated as Day Zones. When activated, “MONITOR ON” will display at the keypad. To deactivate the Watch Mode, arm, then disarm. All Day Zones will re- vert to regular Burglary Zones. Note: The Watch Mode is disabled while armed.

T R O U B L E

R e s e t/ S ys T b l /

A C O N

Y e s / N o

 

 

 

Reset System Trouble? System troubles display and sound at the keypad. Correcting the trouble will clear most indications, however the following error codes will require manual reset: E11; E13; E19; E20 and E22. (See SYSTEM TROUBLE ERROR CODES for a description of error codes).

A C O N

S t ar t / E xi t T m / Y e s / N o

Start Exit Time? (OPTIONAL) (Start Exit Time programmed? !YES !NO). In Commercial Burglary systems, exit delay may have been programmed to start after a central-station “ringback” (verification) signal has been received. If the ringback tone has not been received within about 30 seconds after arming, a communication problem may exist. Use the “START EXIT TIME” Function to start exit delay manually, then exit the premises immediately. Be sure to have your alarm specialist check communications with the central station as soon as possible.

A C O N

T u r nO n / T e l T s t/ Y e s / N o

Activate Telephone Test? (OPTIONAL) (Telephone Test programmed? !YES !NO). Sends a communicator test to the central station. A communication failure will be indicated at the keypad by an “E03-00 COMMFL” display. Repeat the test to attempt to correct a communication failure, as any successful communication will clear this display.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents AC on Ready Operating Guide for yourImportant Test Your System Weekly IntroductionTest your sounding device Test your telephone line Table of Contents AC on Keypad Controls & IndicatorsEnter ResetStay Arming AW AY Setting the Alarm When Leaving Armrst CantARM ArmznfCANT/ARM SystblEXX-XX READY1Arming Stay Protecting Yourself AT Home Arming in Stay ModeSystem Armed Instant Protection Disarm Turning OFF the AL ARM Disarming When ReturningXxxsec Hour Zone 24-Hour Zones programmed? !YES !NO Day Zone Day Zones programmed? !YES !NOTrbl Fire ProtectionFire ZonexxFamily Rehearsal Preparing a Fire Escape PlanImportant! Read Carefully Floorplan FloorplanLimitations of Fire Alarm Warning System Function Menu For user? !YES !NO R nO n / C h i me Y e s / N o L a y / Ar m 1 4/ / N o On Zone 1 has not been received Central Station Monitoring Communicator FeaturesWait Advanced FeaturesZONE02 BypassPage Introduction Programming OptionalProgramming User Codes User Programming Example Select the Program Mode as followsExitxx Keypad MessagesARMED1 Armsnd AlarmCancel ArmsilCode WrongArea TimeOvrr AcfailLobatt CommflClosing Window Optional. a GlossaryGlossary Priority Zone a zone that System Trouble Error Codes Following Statement is Required by the FCC Napco Limited Warranty
Top Page Image Contents