Napco Security Technologies GEM-K2AS manual Limitations of Fire Alarm Warning System

Page 16

FIRE PROTECTION

LIMITATIONS OF FIRE ALARM WARNING SYSTEM

Although a fire alarm system may be of a reliable and state-of- the-art design, neither it nor its peripheral detection devices can offer guaranteed protection against fire. Any such equipment may fail to warn for a variety of reasons:

Control panels, communicators, dialers, smoke detectors, and many other sensing devices will not work without power. Battery- operated devices will not work without batteries, with dead batteries, or with improperly-installed batteries. Devices powered solely by AC will not work if their power source is cut off for any reason.

Fires often cause a failure of electrical power. If the system does not contain a working battery backup power supply, and if the electrical circuit feeding the devices is cut or is not providing power for any reason, the system will not detect heat or smoke or provide any warning of a possible fire.

Telephone lines needed to transmit alarm signals to a central monitoring station may be out of service.

Smoke detectors, though highly effective

in reducing fire deaths, may not activate or provide early-enough warning for a variety of reasons: (a) they may not sense fires that start where smoke cannot reach them, such as in chimneys, walls, roofs, behind closed doors, etc.; (b) they may not sense a fire on a different level of the residence or building; (c) they have sensing limitations; no smoke detector can sense every kind of fire every time.

Thermostatic heat detectors do not always detect fires because the fire may be a slow smoldering low-heat type (producing smoke); because they may not be near the fire; or because the heat of the fire may bypass them. These detectors will not detect oxygen levels, smoke, toxic gases, or flames. Therefore, they may only be used as part of

acomprehensive fire-detection system in conjunction with other devices. Under no circumstances should thermostatic heat detectors be relied upon as the sole measure to ensure fire safety.

Alarm warning devices such as sirens, bells, or horns may not alert someone behind

aclosed or partially-opened door. Warning devices located on one level are less likely to

alert those on a different level. Even those who are awake may not hear the warning if the alarm is obscured by noise from a stereo, radio, air conditioner, or other appliance, or by passing traffic, etc. Alarm warning devices, however loud, may fail to warn the hearing impaired.

Alarm products, as all electrical devices, are subject to component failure. Even though the equipment is designed for many years of trouble-free performance, electronic components could fail at any time.

Above are some of the reasons that fire alarm equipment could fail. The most common cause of an alarm system not functioning when a fire occurs is inadequate testing and maintenance. The system should be tested at least weekly to ensure that all the equipment is working properly.

While an alarm system may make one eligible for lower insurance rates, it is not a substitute for insurance. Homeowners, property owners, and renters are therefore urged to maintain adequate insurance coverage of life and property.

16

Image 16
Contents Operating Guide for your AC on ReadyImportant Test Your System Weekly IntroductionTest your sounding device Test your telephone line Table of Contents Keypad Controls & Indicators AC onEnter ResetStay Arming AW AY Setting the Alarm When Leaving Cant ARMArmznf ArmrstSystbl EXX-XXREADY1 CANT/ARMArming Stay Protecting Yourself AT Home Arming in Stay ModeSystem Armed Instant Protection Disarm Turning OFF the AL ARM Disarming When ReturningXxxsec Day Zone Day Zones programmed? !YES !NO Hour Zone 24-Hour Zones programmed? !YES !NOFire Protection FireZonexx TrblFamily Rehearsal Preparing a Fire Escape PlanImportant! Read Carefully Floorplan FloorplanLimitations of Fire Alarm Warning System Function Menu For user? !YES !NO R nO n / C h i me Y e s / N o L a y / Ar m 1 4/ / N o On Zone 1 has not been received Communicator Features Central Station MonitoringAdvanced Features ZONE02Bypass WaitPage Introduction Programming OptionalProgramming User Codes User Select the Program Mode as follows Programming ExampleExitxx Keypad MessagesARMED1 Alarm CancelArmsil ArmsndWrong AreaTime CodeAcfail LobattCommfl OvrrGlossary Closing Window Optional. aGlossary Priority Zone a zone that System Trouble Error Codes Napco Limited Warranty Following Statement is Required by the FCC