Napoleon Fireplaces GDS25N GDS25P manual Location & Clearances, Stove Dimensions

Page 6

6

LOCATION & CLEARANCES

Provide adequate accessibility clearance for

servicing and operating the stove.

Never obstruct the front opening of the stove.

*AT A DISTANCE OF 2" FROM THE WALL, INSTALLATION OR SERVICE TO THE BLOWER MAY NOT BE PRACTICAL. A MINIMUM OF 5" WILL BE REQUIRED IN ORDER TO INSTALL THE BLOWER.

As long as clearance to combustibles is kept within the re- quired distances, the most desirable and beneficial location for a Napoleon stove is in the centre of a building, thereby allowing the most efficient use of the heat created. The loca- tion of windows, doors and the traffic flow in the room where the stove is to be located should be considered. If possible, you should choose a location where the vent will pass through the house without cutting a floor or roof joist.

STOVE DIMENSIONS

FIGURE 1

17 1/2"

7" DIA.

4" DIA.

25 5/8"

23 5/8"

12 3/4"

23 1/2"

MAINTAIN THESE MINIMUM CLEARANCES MANTEL OR SHELF CLEARANCES: TO COMBUSTIBLES:

COMBUSTIBLE

12”

MANTEL OR TRIM

MAX. MANTEL WIDTH

MATERIAL

 

8”

 

MIN.

 

A. 4"

B. 2"*

C. 2"

FIGURE 2

STOVE SHOULD NOT BE INSTALLED DIRECTLY ON CARPETING. MINIMUM 48" FROM STOVE TOP TO CEILING

TO CEILING FROM STOVE TOP

48"

HORIZONTAL VENT

1"

SIDES AND BOTTOM

TOP

2"

VERTICAL VENT

1"

ALL SIDES

*AT A DISTANCE OF 2" FROM THE WALL, INSTALLATION OR SERVICE TO THE BLOWER MAY NOT BE PRACTICAL. A MINIMUM OF 5" WILL BE REQUIRED IN ORDER TO INSTALL THE BLOWER.

If less than 5" clearance is maintained between the back of the stove and the back wall, it will be necessary to disconnect the venting and gas pipe to move the stove out for installation or service of the blower.

When the

 

fireplace is rear

 

vented, a mantel

 

or shelf may be

 

installed above

 

the GDS25 at a

 

minimum

2

distance of 8".

COMBUSTIBLE MATERIALS

W415-0547 / B / 05.08.06

Image 6
Contents W415-0547 / B What to do if YOU Smell GAS Table of Contents Napoleon GAS Fireplace Presidents Lifetime Limited Warranty General Instructions General InformationCare of GLASS, and Plated Parts Stove Dimensions Location & ClearancesBlower Installation Accent Lite ReplacementAIR Terminal Locations Venting Lengths AIR Terminal Locations Typical Corner Install With Zero RiseVenting Part SupplierTypical Vent Installations Special Vent InstallationsElbow Vent Length Values Horizontal TerminationDefinitions Required Vertical R I S E I N Feet VTFormula 2 HT + VT 24.75 feet HT + VTVertical Termination HT VT3VT + VT =HR + HO = 8 + 5.4 = 13.4 ft = 13.4 + 2.5 = 15.9 ftInstallation Vertical Through Existing ChimneyVertical Installation Horizontal InstallationWall and Ceiling Protection Vertical Venting Installation PER Foot¼ Inch Rise PER Foot Stove Vent Connection Mobile Home InstallationGAS Installation Restricting Vertical VentsFinishing Cast Front InstallationSwitch Functions Door LatchesLogo Placement LOG PlacementOptional Switch / Wiring Diagram Wire Size MAX. LengthOperating Instructions To Turn OFF GASPilot Injector and Orifice Replacement AdjustmentsMaintenance Venturi AdjustmentReplacements Page Trouble Shooting Guide Symptom Problem Test SolutionSymptom Do not Clean Glass When HOTFireplace Service History