Texas Instruments TMS320DM357 DVEVM v2.05 manual About the Decode Demo

Page 27

Running the Standalone Demos

3.3.4About the Decode Demo

Note: You must run the Encode demo before you can run the Decode demo unless you have placed appropriately-named audio and video files on the EVM’s NAND flash storage device. If you see a message that says "File Not Found", please run the Encode demo.

The Decode demo plays audio/speech and video files you select. You can select a source video file and a source audio or speech file. Use the left and right arrow buttons to choose from the demo files and the files created by the Encode demo, which are stored on the EVM’s NAND flash. The decoded signals are sent to your video display and speakers.

The supported video algorithms are H.264 (.264 extension) and MPEG4 (.mpeg4 file extension). The supported speech algorithm is G.711 (.g711 file extension).

Table 3–3 IR Remote Buttons for Decode Demo

IR Remote Button

Mode

Action Performed

 

 

 

Up/Down

--

-- no action --

Left/Right

Setup

Select a different file combination

Play or OK

Setup

Begin decode demo

Record

--

-- no action --

Info/Select

Setup

Show / hide block diagram for demo

Info/Select

Run

Toggle information display

Left/Right

Run

Change information transparency level

Pause

Run

Pause demo (press Play to resume)

Stop

Setup / Run

Return to previous screen

 

 

 

The application runs on the ARM using Linux. The video and audio signals are passed to decoders by the Codec Engine.

To use this demo from the command line, see Section 3.4, Running the

Demos from the Command Line.

Running the Demonstration Software

3-9

Image 27
Contents TMS320DM357 Dvevm Getting Started Guide Important Notice Evaluation BOARD/KIT Important Notice FCC Warning About This Guide PrefaceTrademarks Contents Contents Dvevm Overview What’s in this Kit? DM357 What’s on the Board?What’s Next? EVM Hardware Setup Setting Up the Hardware Audio In P3 Audio Out P5 Composite Video Out J8 Uart P6 Connecting to a Console Window Running the Demonstration Software Starting the Standalone Demos Default Boot ConfigurationStarting the Standalone Demos Starting the Standalone Demos Running the Standalone Demos Shutting Down the Demos About the Encode Demo About the Encode + Decode DemoIR Remote Buttons for Encode Demo IR Remote Buttons for Decode Demo About the Decode DemoRunning the Demos from the Command Line Running the Network Demo Page Dvevm Software Setup Software Overview Command Prompts in This Guide Software Components ApplicationPreparing to Install Installing the Target Linux Software Installing the SoftwareInstalling the Dvsdk Software Exporting a Shared File System for Target Access Installing the A/V Demo FilesSwitch user to root on the host Linux workstation EVM # setenv nfshost ip address of nfs host Testing the Shared File SystemInstalling the Software Writing a Simple Program and Running it on the EVM Setting Up the Build/Development EnvironmentBuilding a New Linux Kernel Compile the kernel using the following commandRebuilding the Dvevm Software for the Target Building with DSPLink EVM # setenv serverip tftp server ip address Booting the New Linux KernelUsing the Digital Video Test Bench Dvtb Page Additional Procedures Ntsc Changing the Video Input/Output MethodsPutting Demo Applications in the Third-Party Menu File filename.tar.gz You should see the following output Setting Up a Tftp ServerBooting from Flash Using Board’s Nand Flash File System Alternate Boot MethodsBooting from Flash Using NFS File System Booting via Tftp Using Board’s Nand Flash File SystemBooting via Tftp Using NFS File System Updating U-Boot Using U-Boot Updating/Restoring the BootloadersTo assign a dynamic address, use the following Updating/Restoring the Bootloaders Updating the Kernel Restoring the Nand FlashRestoring the Nand Flash Using NFS Restoring the Nand Flash Using RAM Disk and a 2 GB SD Card EVM # tar xf /mnt/mmc/dm357flashimage####.tar EVM # cd Page NFS IndexIndex--2 Index--3 Spectrum Digital, Inc 511458-0001B