Vermont Casting 1695 installation instructions Refuel While the Embers Are Still Hot

Page 21

 

ST263

Fig. 36

Start the fire with newspaper and dry kindling.

During the break-in fires, keep the stove temperature under 500°F (260°C) as measured on an optional stove-top thermometer. Adjust the air control lever as necessary to control the fire.

Some odor from the stove’s hot metal, the paint and the cement is normal for the first few fires.

NOTE: Some chimneys need to be “primed,” or warmed up, before they will draw sufficiently to start a fire. To correct this situation, roll up a couple pieces of newspaper, place them on top of the kindling and toward the back of the stove, light them, and close the doors. This should heat the chimney enough to initiate a draft.

Once the draft is established, open the front door and light the rest of the fuel from the bottom. Do not light the main bed of fuel until the chimney begins drawing, and repeat the procedure as often as necessary if the initial attempt is unsuccessful.

4.If your stove has been broken-in previously using Steps 1-3, continue to build the fire gradually. Add larger wood with a diameter of 3-4”(76-102 mm), as in Figure 37.

Continue adding split logs of this size to the briskly- burning fire until there is a glowing ember bed at least 3” (75 mm) deep. A good ember bed is necessary for proper functioning of the catalytic system and may take an hour or more to establish.

5.Close the damper when the griddle temperature reaches 450° F. (230°C).

6.Adjust the air control for your desired heat output.

Refuel While the Embers Are Still Hot

Reload the Intrepid Multi-Fuel while it is still hot and there are plenty of glowing embers to rekindle the fire. Include some smaller pieces of wood in the new load of fuel to help the stove rebuild its operating temperature quickly.

Vermont Castings Intrepid Multi-Fuel

ST264

Fig. 37 Add larger pieces of wood as the fire begins to burn well.

Wear stove gloves, and follow this procedure when you reload your stove:

1.Open the thermostat lever.

2.Open the damper.

3.Check the ash level in the ash pan; empty, if neces- sary, and replace the pan.

4.Use the slicer/poker to freshen the coals. Position the coals in the middle of the firebox.

5.Add fuel.

NOTE: If the remaining charcoal bed is relatively thick and if your fuel is well seasoned, it is possible to add fresh fuel (smaller pieces first), close the door and damper, and reset the primary air thermostat for the desired heat output.

Do not break the charcoal into very small pieces or pound or compress the charcoal bed. It is important that air can circulate under the wood for the fire to be quickly revived.

WARNING: Operate your Intrepid Multi-fuel only with the doors either fully open or fully closed.

CAUTION: The stove will be hot while in operation. Keep children, clothing and furniture away. Contact may cause skin burns.

DO NOT OVERFIRE THIS HEATER. Overfiring may cause a house fire, or can result in permanent dam- age to the stove. If any part of the stove glows, you are overfiring.

ST264a

Fig. 38 Add full size logs when the ember bed is 3” (75mm) deep.

2000970

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Intrepid Welcome Table of ContentsIntrepid Multi-Fuel, Model 1695, 1696 SpecificationsInstallation Outside AirWhat Kind of Chimney to Use Masonry Chimneys Chimney Connector GuidelinesPrefabricated Chimneys Chimney SizeSingle-wall Chimney Connector Double-wall Chimney ConnectorSecuring the Single-wall Connector to a Masonry Chimney Freestanding Chimney InstallationsFireplace Chimney Installations Through a Fireplace Fireplace Chimney Installations Above a FireplaceAn approved wall pass-through for the United States Wall Pass-ThroughsFloor Protection Floor Protection for Fireplace InstallationsReducing Clearances Chimney Connector Clearance ReductionsStove Heat Shields Wall ShieldsMeasured from the top and sides of the stove Fireplace and Mantel Trim ShieldsConstruction Requirements Alcove InstallationsIntrepid Multi-Fuel Clearance Chart Intrepid Multi-fuel Clearance Diagrams Wall Shield Requirements for Common Installations Parallel Installations Assembly Operation Intrepid Multi-fuel’s ControlsPrimary Air Control Glass Door Panels DamperFront Grate Two Ways to Add FuelDamper must be open when starting a fire or when refueling Use the Air Control Settings that Work Best for YouAdd larger pieces of wood as the fire begins to burn well Refuel While the Embers Are Still HotDraft Management Ash DisposalSteel Chimney Indoor/Outdoor locationSingle Venting Pipe & Chimney LayoutCreosote FuelDraft Testing Negative PressureConclusion Maintenance Damper Adjustment How to Adjust the Door LatchTighten the Damper Handle as Needed Replace the Stove Gaskets as NeededPermanent Gaskets Adjust the Door if NecessaryChimney System Annual MaintenanceIntrepid Multi-Fuel Heater Intrepid Multi-Fuel Heater Intrepid Multi-Fuel Heater Warranty

1695 specifications

The Vermont Castings 1695 is a stellar model in the realm of wood stoves, noted for its blend of traditional craftsmanship and modern efficiency. This timeless piece not only serves as a functional heating solution but also as a stylish addition to home décor, making it a popular choice for homeowners seeking both utility and aesthetics.

One of the standout features of the Vermont Castings 1695 is its impressive heating capacity. With the ability to heat areas up to 2,000 square feet, this stove is ideal for larger living spaces or for providing supplementary heat in smaller homes. Its robust construction, crafted from heavy-duty cast iron, ensures that heat is evenly distributed throughout the room, creating a cozy atmosphere.

The 1695’s primary innovation lies in its advanced combustion technology. With a patented secondary combustion process, this wood stove maximizes efficiency by re-burning gases and particulates that would typically escape through the flue. This not only results in cleaner emissions, which is beneficial for the environment, but also means longer burn times and less frequent reloading of wood, allowing users to enjoy their fire without constant maintenance.

Moreover, the Vermont Castings 1695 features a smooth-operating air control system. This system enables users to easily adjust the burn rate, which helps to manage heat output and fuel consumption. This level of control ensures that the stove operates at peak efficiency, reducing waste and optimizing performance.

In terms of design, the Vermont Castings 1695 boasts an elegant look with a classic cast-iron façade and an attractive firebox window. The large viewing window allows users to enjoy the mesmerizing flames while providing a source of warmth. The design is not just visually appealing; the cast iron surface also retains heat well, radiating warmth long after the fire has died down.

Durability is another hallmark of the Vermont Castings brand, and the 1695 model is no exception. Built to last, it withstands the rigors of regular use, making it a wise investment for homeowners. Additionally, the stove is available in various finishes, allowing for customization to fit different home styles.

In summary, the Vermont Castings 1695 is a well-rounded wood stove that combines traditional aesthetics with modern technologies. Its efficiency, effective heating capability, and attractive design make it a favored choice among wood stove enthusiasts and environmentally conscious consumers alike. Whether used as a primary heating source or a supplemental one, this stove delivers warmth, comfort, and style.
Top Page Image Contents