Vermont Casting 1695 Ash Disposal, Draft Management, Steel Chimney, Indoor/Outdoor location

Page 22

Vermont Castings Intrepid Multi-Fuel

Ash Disposal

Remove ash before it reaches the top of the ash pan. Check the level at least once a day, and before each refueling. If the ash is close to the top edge of the pan, empty it according to this procedure:

1.Open the damper.

2.Open the front doors fully.

3.Using stove gloves, pull the ash pan out of the stove by its handle.

4.Remove the ash pan and properly dispose of the ashes. Be sure to keep the pan level during dispos- al.

5.Return the ash pan to the stove.

Empty the ash pan regularly, typically every one to three days. The frequency will vary depending on how you operate your stove; if you burn more wood at higher heat output settings, ash will accumulate rapidly.

Remove ash frequently and place it outdoors in a metal container with a tight-fitting lid. Put the closed container of ash on a noncombustible floor or on the ground, well away from all combustible materials, pending final disposal. If the ash is disposed of by burial in soil or otherwise locally dispersed, keep it in the closed con- tainer until all cinders have thoroughly cooled. You can use wood ash as a garden fertilizer.

CAUTION: Never use your household or shop vacuum cleaner to remove ash from the stove; always remove and dispose of the ash properly.

Draft Management

A stove is part of a system, which includes the chimney, the operator, the fuel, and the home. The other parts of the system will affect how well the stove works. When there is a good match between all the parts, the system works well.

Wood stove operation depends on natural (unforced) draft. Natural draft occurs when the smoke is hotter (and therefore lighter) than the outdoor air at the top of the chimney. The bigger the temperature difference, the stronger the draft. As the smoke rises from the chimney it provides suction or ‘draw’ that pulls air into the stove for combustion. A slow, lazy fire with the stove’s air inlet fully open indicates a weak draft. A brisk fire, supported only by air entering the stove through the normal inlet, indicates a good draft. The stove’s air inlet is passive; it regulates how much air can enter the stove, but it doesn’t move air into it.

Depending on the features of your installation - steel or masonry chimney, inside or outside the house, matched to the stove’s outlet or oversized - your system may warm up quickly, or it may take a while to warm up and operate well. With an ‘airtight’ stove, one which restricts the amount of air getting into the firebox, the chimney

must keep the smoke warm all the way to the outdoors. Some chimneys do this better than others. Here’s a list of features and their effects.

Masonry Chimney

Masonry is a traditional material for chimneys, but it can perform poorly when it serves an ‘airtight’ stove. Masonry is a very effective ‘heat sink’ - it absorbs a lot of heat. It can cool the smoke enough to diminish draft. The bigger the chimney, the longer it takes to warm up. It’s often very difficult to warm up an outdoor masonry chimney, especially an oversized one, and keep it warm enough to maintain an adequate draft.

Steel Chimney

Most factory-made steel chimneys have a layer of in- sulation around the inner flue. This insulation keeps the smoke warm. The insulation is less dense than mason- ry, so the inner steel liner warms up more quickly than a masonry chimney. Steel doesn’t have the good looks of masonry, but it performs much better.

Indoor/Outdoor location

Because the chimney must keep the smoke warm, it’s best to locate it inside the house. This uses the house as insulation for the flue and allows a little heat release into the home. An indoor chimney won’t lose its heat to the outdoors, so it takes less heat from the stove to get it warm and keep it warm.

Flue sizing

The inside size of a chimney for an ‘airtight’ stove should match the size of the stove’s flue outlet. When a chimney serves an airtight stove, more is not better; in fact, it can be a disadvantage. Hot gases cool off through expansion; if we vent a stove with a six-inch flue collar (28 square inch area) into a 10 x 10” flue, the gases expand to over three times their original size. This cools the gases, which weakens draft strength. If an oversized flue is also outside the house, the heat it absorbs gets transferred to the outdoor air and the flue usually stays cool.

It’s common for a masonry flue, especially one built for a fireplace, to be oversized for an airtight stove. It can take quite a while to warm up such a flue, and the re- sults can be disappointing. The best solution to an over- sized flue is an insulated steel chimney liner, the same diameter as the stove or insert’s flue outlet; the liner keeps the smoke at its original volume, and the result is a stronger draft. An uninsulated liner is a second choice

-the liner keeps the smoke restricted to its original size, but the smoke still must warm up the air around the liner. This makes the warm-up process take longer.

22

2000970

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Intrepid Table of Contents WelcomeSpecifications Intrepid Multi-Fuel, Model 1695, 1696Outside Air InstallationWhat Kind of Chimney to Use Prefabricated Chimneys Chimney Connector GuidelinesMasonry Chimneys Chimney SizeSecuring the Single-wall Connector to a Masonry Chimney Double-wall Chimney ConnectorSingle-wall Chimney Connector Freestanding Chimney InstallationsFireplace Chimney Installations Above a Fireplace Fireplace Chimney Installations Through a FireplaceWall Pass-Throughs An approved wall pass-through for the United StatesFloor Protection for Fireplace Installations Floor ProtectionStove Heat Shields Chimney Connector Clearance ReductionsReducing Clearances Wall ShieldsFireplace and Mantel Trim Shields Measured from the top and sides of the stoveAlcove Installations Construction RequirementsIntrepid Multi-Fuel Clearance Chart Intrepid Multi-fuel Clearance Diagrams Wall Shield Requirements for Common Installations Parallel Installations Assembly Intrepid Multi-fuel’s Controls OperationPrimary Air Control Front Grate DamperGlass Door Panels Two Ways to Add FuelUse the Air Control Settings that Work Best for You Damper must be open when starting a fire or when refuelingRefuel While the Embers Are Still Hot Add larger pieces of wood as the fire begins to burn wellSteel Chimney Ash DisposalDraft Management Indoor/Outdoor locationCreosote Pipe & Chimney LayoutSingle Venting FuelNegative Pressure Draft TestingConclusion Maintenance Tighten the Damper Handle as Needed How to Adjust the Door LatchDamper Adjustment Replace the Stove Gaskets as NeededAdjust the Door if Necessary Permanent GasketsAnnual Maintenance Chimney SystemIntrepid Multi-Fuel Heater Intrepid Multi-Fuel Heater Intrepid Multi-Fuel Heater Warranty

1695 specifications

The Vermont Castings 1695 is a stellar model in the realm of wood stoves, noted for its blend of traditional craftsmanship and modern efficiency. This timeless piece not only serves as a functional heating solution but also as a stylish addition to home décor, making it a popular choice for homeowners seeking both utility and aesthetics.

One of the standout features of the Vermont Castings 1695 is its impressive heating capacity. With the ability to heat areas up to 2,000 square feet, this stove is ideal for larger living spaces or for providing supplementary heat in smaller homes. Its robust construction, crafted from heavy-duty cast iron, ensures that heat is evenly distributed throughout the room, creating a cozy atmosphere.

The 1695’s primary innovation lies in its advanced combustion technology. With a patented secondary combustion process, this wood stove maximizes efficiency by re-burning gases and particulates that would typically escape through the flue. This not only results in cleaner emissions, which is beneficial for the environment, but also means longer burn times and less frequent reloading of wood, allowing users to enjoy their fire without constant maintenance.

Moreover, the Vermont Castings 1695 features a smooth-operating air control system. This system enables users to easily adjust the burn rate, which helps to manage heat output and fuel consumption. This level of control ensures that the stove operates at peak efficiency, reducing waste and optimizing performance.

In terms of design, the Vermont Castings 1695 boasts an elegant look with a classic cast-iron façade and an attractive firebox window. The large viewing window allows users to enjoy the mesmerizing flames while providing a source of warmth. The design is not just visually appealing; the cast iron surface also retains heat well, radiating warmth long after the fire has died down.

Durability is another hallmark of the Vermont Castings brand, and the 1695 model is no exception. Built to last, it withstands the rigors of regular use, making it a wise investment for homeowners. Additionally, the stove is available in various finishes, allowing for customization to fit different home styles.

In summary, the Vermont Castings 1695 is a well-rounded wood stove that combines traditional aesthetics with modern technologies. Its efficiency, effective heating capability, and attractive design make it a favored choice among wood stove enthusiasts and environmentally conscious consumers alike. Whether used as a primary heating source or a supplemental one, this stove delivers warmth, comfort, and style.
Top Page Image Contents