Vermont Casting 1695 Installation, Outside Air, What Kind of Chimney to Use

Page 4

Vermont Castings Intrepid Multi-Fuel

Installation

SAFETY NOTICE: IF YOUR STOVE IS NOT PROP- ERLY INSTALLED, A HOUSE FIRE MAY RESULT. TO REDUCE THE RISK OF FIRE, FOLLOW THE INSTALLATION INSTRUCTIONS. CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRIC- TIONS AND INSTALLATION INSPECTION REQUIRE- MENTS IN YOUR AREA.

Before you begin an installation, review your plans to see that:

•Your stove and chimney connector will be far enough from combustible material to meet all clearance requirements.

•The floor protector is large enough and is con- structed properly to meet all requirements.

•You have all necessary permits from local author- ities.

Your local building official is the final authority for ap- proving your installation as safe and determining that it meets local and state codes.

The metal label permanently attached to the back of every Vermont Castings stove indicates that the stove has been tested to current ULC standards, and gives the name of the testing laboratory. Clearance and in- stallation information also is printed on the label. When the stove is installed according to the information both on the label and in this manual, local authorities in most cases will accept the label as evidence that the installa- tion meets codes and can be approved.

However, codes vary in different areas. Before starting the installation, review your plans with the local building authority. You local dealer can provide any additional information needed.

For any unresolved installation issues, refer to CSA CAN-B365 Installation Code for Solid Fuel Burning Appliances and Equipment. These standards are the basis for many national codes. They are nationally recognized and are accepted by most local authorities. Your local dealer or your local building official may have a copy of these regulations.

IMPORTANT: FAILURE TO FOLLOW THESE IN- STALLATION INSTRUCTIONS MAY RESULT IN A DANGEROUS SITUATION, INCLUDING A CHIMNEY OR HOUSE FIRE. FOLLOW ALL INSTRUCTIONS EXACTLY, AND DO NOT ALLOW MAKESHIFT COM- PROMISES TO ENDANGER PROPERTY AND PER- SONAL SAFETY.

Outside Air

In some modern, super-insulated homes, there is not enough air for combustion because of insufficient air infiltration into the building. Such air enters a home through unsealed cracks and openings. Kitchen or bath exhaust fans can compete with the stove for available air and compound the problem.

When poor draft is caused by a low infiltration rate, opening a ground floor window on the windward side of the house and in the vicinity of the stove will usually alleviate the problem.

Another solution is to install a permanent outside air supply to the stove and/or room. In some areas, in fact, bringing air for combustion from outside the home directly to the air inlet of the stove is required for new construction.

An outside air supply is not affected by pressure varia- tions within the house, and improved stove perfor- mance often results. An Outside Air Adapter Kit #33258 for the Intrepid II is available from your local Vermont Castings dealer.

What Kind of Chimney to Use

Your Intrepid Multi-fuel must be connected to a code- approved masonry chimney with a flue liner, to a relined masonry chimney that meets local codes, or to a prefabricated metal chimney that complies with the requirements for Type HT chimneys in the Standard for Chimneys, Factory-Built, Residential Type and Building Heating Appliance, UL 103, or the High Temperature (650°C) Standard ULC S-629 for Canada. Whatever kind you use, the chimney and chimney connector must be in good condition and kept clean. Figure 2 shows the two chimney types.

Aprefabricated double-wall insu-

lated chimney

A tile-lined ma- sonry chimney

ST241

Fig. 2 Standard chimney types.

4

2000970

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Intrepid Table of Contents WelcomeSpecifications Intrepid Multi-Fuel, Model 1695, 1696Outside Air InstallationWhat Kind of Chimney to Use Chimney Connector Guidelines Masonry ChimneysPrefabricated Chimneys Chimney SizeDouble-wall Chimney Connector Single-wall Chimney ConnectorSecuring the Single-wall Connector to a Masonry Chimney Freestanding Chimney InstallationsFireplace Chimney Installations Above a Fireplace Fireplace Chimney Installations Through a FireplaceWall Pass-Throughs An approved wall pass-through for the United StatesFloor Protection for Fireplace Installations Floor ProtectionChimney Connector Clearance Reductions Reducing ClearancesStove Heat Shields Wall ShieldsFireplace and Mantel Trim Shields Measured from the top and sides of the stoveAlcove Installations Construction RequirementsIntrepid Multi-Fuel Clearance Chart Intrepid Multi-fuel Clearance Diagrams Wall Shield Requirements for Common Installations Parallel Installations Assembly Intrepid Multi-fuel’s Controls OperationPrimary Air Control Damper Glass Door PanelsFront Grate Two Ways to Add FuelUse the Air Control Settings that Work Best for You Damper must be open when starting a fire or when refuelingRefuel While the Embers Are Still Hot Add larger pieces of wood as the fire begins to burn wellAsh Disposal Draft ManagementSteel Chimney Indoor/Outdoor locationPipe & Chimney Layout Single VentingCreosote FuelNegative Pressure Draft TestingConclusion Maintenance How to Adjust the Door Latch Damper AdjustmentTighten the Damper Handle as Needed Replace the Stove Gaskets as NeededAdjust the Door if Necessary Permanent GasketsAnnual Maintenance Chimney SystemIntrepid Multi-Fuel Heater Intrepid Multi-Fuel Heater Intrepid Multi-Fuel Heater Warranty

1695 specifications

The Vermont Castings 1695 is a stellar model in the realm of wood stoves, noted for its blend of traditional craftsmanship and modern efficiency. This timeless piece not only serves as a functional heating solution but also as a stylish addition to home décor, making it a popular choice for homeowners seeking both utility and aesthetics.

One of the standout features of the Vermont Castings 1695 is its impressive heating capacity. With the ability to heat areas up to 2,000 square feet, this stove is ideal for larger living spaces or for providing supplementary heat in smaller homes. Its robust construction, crafted from heavy-duty cast iron, ensures that heat is evenly distributed throughout the room, creating a cozy atmosphere.

The 1695’s primary innovation lies in its advanced combustion technology. With a patented secondary combustion process, this wood stove maximizes efficiency by re-burning gases and particulates that would typically escape through the flue. This not only results in cleaner emissions, which is beneficial for the environment, but also means longer burn times and less frequent reloading of wood, allowing users to enjoy their fire without constant maintenance.

Moreover, the Vermont Castings 1695 features a smooth-operating air control system. This system enables users to easily adjust the burn rate, which helps to manage heat output and fuel consumption. This level of control ensures that the stove operates at peak efficiency, reducing waste and optimizing performance.

In terms of design, the Vermont Castings 1695 boasts an elegant look with a classic cast-iron façade and an attractive firebox window. The large viewing window allows users to enjoy the mesmerizing flames while providing a source of warmth. The design is not just visually appealing; the cast iron surface also retains heat well, radiating warmth long after the fire has died down.

Durability is another hallmark of the Vermont Castings brand, and the 1695 model is no exception. Built to last, it withstands the rigors of regular use, making it a wise investment for homeowners. Additionally, the stove is available in various finishes, allowing for customization to fit different home styles.

In summary, the Vermont Castings 1695 is a well-rounded wood stove that combines traditional aesthetics with modern technologies. Its efficiency, effective heating capability, and attractive design make it a favored choice among wood stove enthusiasts and environmentally conscious consumers alike. Whether used as a primary heating source or a supplemental one, this stove delivers warmth, comfort, and style.
Top Page Image Contents