Vermont Casting 1695 installation instructions Fireplace Chimney Installations Above a Fireplace

Page 7

Thimble

Thimble Sleeve

Chimney

Connector

45° Elbow

Max.

Flue

ST243a

Fig. 5 The thimble, made of either ceramic or metal, must be cemented securely in place.

Without a thimble, a suitable length of chimney con- nector can be extended through the breach to the inner face of the flue liner, and cemented securely in place. Additional pieces of connector are then attached with sheet metal screws.

Fireplace Chimney Installations -

Above a Fireplace

The Intrepid Multi-fuel may be connected to a chimney above a fireplace opening also. In such installations, the stove is positioned on the hearth in front of the fire- place and the chimney connector rises from the stove top and then angles 45° back into the chimney. (Fig. 6)

The chimney liner should extend to the point at which the chimney connector enters the chimney.

If the chimney connector from your installation enters the chimney above a fireplace, follow all the guidelines mentioned above for freestanding installations. In addi- tion, give special consideration to the following points:

•Check the clearance between the stove and the chimney connector, and any combustible trim or the mantel. Use the necessary combination of mantel, trim, and connector heat shields to achieve the required clearances.

•Check the clearance between the chimney con- nector and the ceiling. If no heat shields are used, the clearance should be at least 26” (660 mm). To find out how much this clearance may be reduced with heat shields, see the clearance chart on Page 13.

•The fireplace damper must be sealed to prevent room air from escaping up the flue. However, it must be possible to reopen the damper to inspect or clean the chimney.

Vermont Castings Intrepid Multi-Fuel

 

* Check

*

 

These Clear-

 

 

 

ances

 

 

Chimney Con-

 

 

nector Shield

Mantel

 

 

 

 

*

 

 

Seal the

 

 

Damper

 

 

ST244a

Fig. 6

Chimney connector enters chimney above the fire-

place.

 

 

Fireplace Chimney Installations -

Through a Fireplace

If your fireplace height is at least 25” (635 mm), you may install an Intrepid Multi-fuel with standard legs through the fireplace opening using a 90° Tee kit avail- able from your local dealer. This positive connection kit ensures a tight fit between the stove flue collar and the chimney flue. (Fig. 7)

Fireplace installations, whether connected to the flue above or through the fireplace opening, have special clearance requirements to adjacent trim and the mantel. You will find the required clearances for the Intrepid Multi-fuel fireplace installations on Page 13.

Floor protection requirements also apply to fireplace installations. Floor protection information is on Page 9.

2000970

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Intrepid Welcome Table of ContentsIntrepid Multi-Fuel, Model 1695, 1696 SpecificationsOutside Air InstallationWhat Kind of Chimney to Use Chimney Size Chimney Connector GuidelinesMasonry Chimneys Prefabricated ChimneysFreestanding Chimney Installations Double-wall Chimney ConnectorSingle-wall Chimney Connector Securing the Single-wall Connector to a Masonry ChimneyFireplace Chimney Installations Through a Fireplace Fireplace Chimney Installations Above a FireplaceAn approved wall pass-through for the United States Wall Pass-ThroughsFloor Protection Floor Protection for Fireplace InstallationsWall Shields Chimney Connector Clearance ReductionsReducing Clearances Stove Heat ShieldsMeasured from the top and sides of the stove Fireplace and Mantel Trim ShieldsConstruction Requirements Alcove InstallationsIntrepid Multi-Fuel Clearance Chart Intrepid Multi-fuel Clearance Diagrams Wall Shield Requirements for Common Installations Parallel Installations Assembly Intrepid Multi-fuel’s Controls OperationPrimary Air Control Two Ways to Add Fuel DamperGlass Door Panels Front GrateDamper must be open when starting a fire or when refueling Use the Air Control Settings that Work Best for YouAdd larger pieces of wood as the fire begins to burn well Refuel While the Embers Are Still HotIndoor/Outdoor location Ash DisposalDraft Management Steel ChimneyFuel Pipe & Chimney LayoutSingle Venting CreosoteNegative Pressure Draft TestingConclusion Maintenance Replace the Stove Gaskets as Needed How to Adjust the Door LatchDamper Adjustment Tighten the Damper Handle as NeededPermanent Gaskets Adjust the Door if NecessaryChimney System Annual MaintenanceIntrepid Multi-Fuel Heater Intrepid Multi-Fuel Heater Intrepid Multi-Fuel Heater Warranty

1695 specifications

The Vermont Castings 1695 is a stellar model in the realm of wood stoves, noted for its blend of traditional craftsmanship and modern efficiency. This timeless piece not only serves as a functional heating solution but also as a stylish addition to home décor, making it a popular choice for homeowners seeking both utility and aesthetics.

One of the standout features of the Vermont Castings 1695 is its impressive heating capacity. With the ability to heat areas up to 2,000 square feet, this stove is ideal for larger living spaces or for providing supplementary heat in smaller homes. Its robust construction, crafted from heavy-duty cast iron, ensures that heat is evenly distributed throughout the room, creating a cozy atmosphere.

The 1695’s primary innovation lies in its advanced combustion technology. With a patented secondary combustion process, this wood stove maximizes efficiency by re-burning gases and particulates that would typically escape through the flue. This not only results in cleaner emissions, which is beneficial for the environment, but also means longer burn times and less frequent reloading of wood, allowing users to enjoy their fire without constant maintenance.

Moreover, the Vermont Castings 1695 features a smooth-operating air control system. This system enables users to easily adjust the burn rate, which helps to manage heat output and fuel consumption. This level of control ensures that the stove operates at peak efficiency, reducing waste and optimizing performance.

In terms of design, the Vermont Castings 1695 boasts an elegant look with a classic cast-iron façade and an attractive firebox window. The large viewing window allows users to enjoy the mesmerizing flames while providing a source of warmth. The design is not just visually appealing; the cast iron surface also retains heat well, radiating warmth long after the fire has died down.

Durability is another hallmark of the Vermont Castings brand, and the 1695 model is no exception. Built to last, it withstands the rigors of regular use, making it a wise investment for homeowners. Additionally, the stove is available in various finishes, allowing for customization to fit different home styles.

In summary, the Vermont Castings 1695 is a well-rounded wood stove that combines traditional aesthetics with modern technologies. Its efficiency, effective heating capability, and attractive design make it a favored choice among wood stove enthusiasts and environmentally conscious consumers alike. Whether used as a primary heating source or a supplemental one, this stove delivers warmth, comfort, and style.
Top Page Image Contents