Liebert AC4 user manual View Output Status

Page 66

View Status Menus

A.4.5 View Output Status

For details on this feature, see 5.5 - View Output Status.

View Output Status


OUTPUT STATUS
Output status to device
OUTPUT	STATE	MODE	ZONE	*****************************************
				OPERATING	= OPERATING/ON
DEVICE_1	ON	ALARM	1	STANDBY	= IN STANDBY MODE
DEVICE_2	ON	OPERATING	1	ALARM	= IN ALARM
DEVICE_3	OFF	STANDBY	1	FORCE ON	= FORCE ON BY OPERATOR
DEVICE_4	OFF	ALARM	1	FORCE OFF	= FORCE OFF BY OPERATOR
				HW FORCE ON	= FORCE ON BY HARDWARE SWITCH
1=REFRESH OUTPUT		STATUS		PENDING	= PENDING DELAY TIMER
2=RETURN TO MAIN		MENU		NOT USED	= DEVICE NOT USED
				*****************************************
SELECT A NUMBER:

Image 66

Contents AC4 MonitoringPage Table of Contents Setup System Setup Common Alarm 7.5 Setup System Setup Zones Appendix a Service Terminal Interface Setup MenuFigures Data Logs Methods of Viewing and Configuring the AC4Available Alarms IntroductionLCD for configuration Outside Enclosure OverviewOperation Typical Configuration Device Liebert ChallengerDevice RS232 Liebert Himod Controller Board Overview Controller board componentsLCD connector Connector RS232DIP switch 24VAC powerLED Indicators LED indicators summaryOutput LEDs Status LEDs Input LEDs Typical Sequence Packing Contents Installation ConsiderationsInstallation Unpacking and Preliminary InspectionSurface-Mounting the AC4 Required toolsMounting the Panel Flush-Mounting the AC4 Connect Power to the AC4 Electrical connections to panelWiring Specifications Wiring and ConnectionsWiring specifications Connecting Digital Inputs Connecting Digital Inputs and OutputsConnecting Liebert Environmental Units Connecting Digital OutputsSetting the Digital Output Jumpers Connecting Common Alarm OutputsRS232 Connector Digital output jumper settingsOverview of Menus Guide to AC4 functionsOpening Screen Overview Main Menu OverviewLCD Menu Overview View Status Options Clearing Active Alarms View Active AlarmsActive Alarms Active AlarmsAlarm log conditions View Alarm LogAlarm Log Alarm LogEvent log conditions View Event LogEvent Log Event LogViewing Additional Input Data View Input StatusInput Status Digital input statesViewing Additional Output Data View Output StatusOutput Status Digital output statesSilence Alarm & Backup LOG Files Service Terminal Interface Silence Alarm Service Terminal Interface onlyBack Up Log Files Service Terminal Interface only Silence Alarm & Backup Log Files Service Terminal Interface System and Control Options LoginLogin Valid characters for data entrySetup System menu Login ScreenSystem & Control menu Clear Alarms&Logs selected Clear Alarms/Logs menuSetup System Overview Setup System Setup InputsDefine Input as Alarmable or Event Change Label Name of InputDefine Input as Normally Open or Normally Closed Delay Time Set Up Alarmable Inputs in Latched or Unlatched ModeSet Up Delay Time Latched / UnlatchedSetup System Setup Common Alarm Change to Reset Y or Not Reset NReset Common Alarm Message if too few devices entered Setup System Setup ZonesSet Up a Zone Message if too many devices enteredSetup System Setup Outputs Define Output as Normally Open or Normally ClosedConfigure Output for Loss of Power Fail-Safe Define Operating or Standby ModeEnable or Disable an Output Device in Alarm Status Set ModeChange the Password Setup System Setup System InfoChange Password Reset Password to the Factory Default AaaaSet Date & Time/Automatic Daylight Saving Time Setup Site IDSetup Site ID Set Date & TimeBackup and Upload Configuration File Back Up the Configuration File Upload the Configuration File Factory Defaults Factory DefaultsFirmware Update Service Terminal Interface only System and Control Options Setup Operation Menu Setup OperationSelect Setup Operation Setup System Menu Default settings operation featuresSet Interval & Start Time 1- to 99-Day Interval Turn Automatic Sequencing On or OffActivate / Deactivate Set Start Time Hour IntervalSpecify Failed Standby Response Turn Standby Testing On or OffChange Standby Testing Failed Standby responseSetup Operation Menu Specify Hold Delay TimeHold Delay Time Restart Delay TimeOverride Output Clear the Alarm Log Clear Alarms & LogsClear Active Alarms Clear the Event LogAC4 Specifications SpecificationsAppendix a Service Terminal Interface Comparison of Functions LCD and Service Terminal InterfaceConnecting to the Service Terminal Interface COM1 Port Setup Create a ConnectionSpecify COM Port Connection Settings tab Properties SetupAscii Setup Ascii Setup buttonConnect to the Service Terminal Interface Click on the file name for example, AC4.htView Status Overview Silence Alarm and Backup Log FilesSetup Menu Overview Main Menu For sample screens, seeView Status Menus Main MenuMain Menu View Active Alarms View Active Alarms View Alarm Log View Alarm LogView Event Log View Event LogView Input Status View Input StatusView Output Status View Output StatusSilence Alarm Section A.5.1 Section A.5.2Backup Log Files Event Log File Back Up Alarm Log FileBackup Log Files Alarm Log File Back Up Event Log FileSetup Menu Login MenuLogin Tips on Using the Service Terminal Interface Setup MenuSetup Menu See DescriptionSetup Inputs Setup InputsSetup Common Alarm Setup Common AlarmSetup Zones Setup ZonesSetup Outputs Setup OutputsSetup System Info Setup System InfoChange Password Setup Site ID Set Date & TimeBackup & Upload Configuration File Backup Backup & Upload Configuration File Upload Factory DefaultsFirmware Update Service Terminal Interface only Firmware UpdateSetup Operation Setup Operation Auto SequencingAuto Sequencing Standby Testing Setup Operation Standby TestingSetup Operation Hold Delay Hold DelaySetup Operation Failed Standby Failed StandbyRestart Delay Setup Operation Restart DelayOverride Output Override OutputClear Alarms & Logs Clear Alarms & Logs Clear Active AlarmsClear Alarms & Logs Clear the Alarm Log Clear Alarms & Logs Clear the Event Log Page Locations Technical Support/ServiceCompany Behind the Products Asia 23F, Allied Kajima Bldg

Related manuals

Manual 4 pages 49.53 Kb